power-state
FUTURESMART-MIB ·
.1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.65
Object
scalar
optional
r/w
Enumeration
This object is used to inquire about and to control the 'power state' of the device. The exact meaning of each enumeration may vary from device to device, but the general interpretation is as follows: ePowerStateAwake: The device is idle (immediately ready to process a job) or processing a job. ePowerStatePowerSave: The device is in a low power state and will not be immediately available to process an incoming job. A 'warm-up time' of several seconds can be expected. ePowerStateSleep: The device is in a sleep state. It uses less power than when in the power save state. It can also be expected to need a substantially longer warm-up time than when in the power save state. ePowerStateOff: The device is powered off. Note that when the device is powered off then SNMP/PML requests obviously cannot be honored. Therefore ePowerStateOff will likely never be returned from a PML get operation. However, ePowerStateOff could potentially be used in a PML set operation to power down the device if it has a software/firmware controllable power switch. For a given product it may not be possible to have the device enter the requested state due to the current state of the device. E.g., it may not be possible to enter the power save state if the device currently is in the sleep state. In this case a set operation will have an execution outcome of <ErrorActionCanNotBePerformedNow>. The same execution outcome can be expected if the device is processing a job and an attempt is made to e.g. bring the device into the power save state or the sleep state. A get operation on the object returns the current power state of the device. While the device is transitioning from one state to another one of the values ePowerStateTransitioningToAwake, ePowerStateTransitioningToPowerSave, ePowerStateTransitioningToSleep or ePowerStateTransitioningToOff will be returned from a PML get operation. An attempt to perform a PML set with any of these four values will yield <ErrorInvalidOrUnsupportedValue>
Context
- MIB
- FUTURESMART-MIB
- OID
.1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.65- Type
- scalar
- Access
- readwrite
- Status
- optional
- Parent
- settings-system
- Siblings
- 12
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | ePowerStateAwake |
2 | ePowerStatePowerSave |
3 | ePowerStateSleep |
4 | ePowerStateOff |
5 | ePowerStateTransitioningToAwake |
6 | ePowerStateTransitioningToPowerSave |
7 | ePowerStateTransitioningToSleep |
8 | ePowerStateTransitioningToOff |
9 | ePowerStateReboot |
10 | ePowerStateAutoOff |
11 | ePowerState1Watt |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| energy-star optional Returns or changes the Energy Star sleep value. If the value
is greater than zero, then the device will go into energy
saving sleep mode after the print engine has been idle for t… | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.1 |
| enable-engine-early-warmup optional This PML object is used by HP SW to enable/disable the printer
to send the signal of warm-up process early to engine. The
effect of warming up early will reduce the First Page Out… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.101 |
| sleep-mode optional Returns eTrue if the device is in energy saving sleep mode,
otherwise returns eFalse. Setting SLEEP-MODE to eFalse causes
the device to wake up, if it is in sleep mode. Setting
SL… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.2 |
| date-display optional Controls front-panel date display format. | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.22 |
| mono-color-switching-mode optional This object allows the user to view/change the color/mono
switching mode for a device | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.31 |
| device-configure | node | - | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.32 |
| direct-connect-ports-enable optional This object specifies whether all direct connect ports
(parallel and USB) are available or ignored. JetDirect,
embedded network connectivity, and third party add-on cards
(such as… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.43 |
| factory-reset optional writing an INTEGER 0 will do factory reset on system variables,
MFP Settings and the .NET database without a reboot. | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.68 |
| order-cartridge optional Used to enable/disable the supplies status message that is
shown when the supply reaches low | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.71 |
| powersave-enable-type optional ePowerSaveOff - printer stays awake all the time, can only
sleep if sleep button is hit. ePowerSaveUseSleepDelay - use
sleep delay the old way, sleep schedule is ignored .
ePowerS… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.89 |
| large-size-media-default-grain-direction optional This object identifies default grain direction for large size
media (B/A3) only. Default value is eShortGrain | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.97 |
| start-engine-early-warmup mandatory This PML object is used by HP SW drivers to signal the printer
that a job is coming, and to start the warm-up process
early.The effect of warming up early will reduce the First Pa… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.99 |