energy-star
FUTURESMART-MIB ·
.1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.1
Object
scalar
optional
r/w
Integer32
Returns or changes the Energy Star sleep value. If the value is greater than zero, then the device will go into energy saving sleep mode after the print engine has been idle for the number of seconds specified by this object. A value of zero means Energy Star is disabled and the device will not go to sleep based on print engine idle time. The value must be non-negative.
Context
- MIB
- FUTURESMART-MIB
- OID
.1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.1- Type
- scalar
- Access
- readwrite
- Status
- optional
- Parent
- settings-system
- Siblings
- 12
Syntax
Integer32
- Source
- COPS-PR-SPPIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| enable-engine-early-warmup optional This PML object is used by HP SW to enable/disable the printer
to send the signal of warm-up process early to engine. The
effect of warming up early will reduce the First Page Out… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.101 |
| sleep-mode optional Returns eTrue if the device is in energy saving sleep mode,
otherwise returns eFalse. Setting SLEEP-MODE to eFalse causes
the device to wake up, if it is in sleep mode. Setting
SL… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.2 |
| date-display optional Controls front-panel date display format. | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.22 |
| mono-color-switching-mode optional This object allows the user to view/change the color/mono
switching mode for a device | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.31 |
| device-configure | node | - | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.32 |
| direct-connect-ports-enable optional This object specifies whether all direct connect ports
(parallel and USB) are available or ignored. JetDirect,
embedded network connectivity, and third party add-on cards
(such as… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.43 |
| power-state optional This object is used to inquire about and to control the 'power
state' of the device. The exact meaning of each enumeration may
vary from device to device, but the general interpre… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.65 |
| factory-reset optional writing an INTEGER 0 will do factory reset on system variables,
MFP Settings and the .NET database without a reboot. | scalar | Integer32 | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.68 |
| order-cartridge optional Used to enable/disable the supplies status message that is
shown when the supply reaches low | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.71 |
| powersave-enable-type optional ePowerSaveOff - printer stays awake all the time, can only
sleep if sleep button is hit. ePowerSaveUseSleepDelay - use
sleep delay the old way, sleep schedule is ignored .
ePowerS… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.89 |
| large-size-media-default-grain-direction optional This object identifies default grain direction for large size
media (B/A3) only. Default value is eShortGrain | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.97 |
| start-engine-early-warmup mandatory This PML object is used by HP SW drivers to signal the printer
that a job is coming, and to start the warm-up process
early.The effect of warming up early will reduce the First Pa… | scalar | Enumeration | .1.3.6.1.4.1.11.2.3.9.4.2.1.1.1.99 |