flWorkWlanIf1ScbManMacMode

FL-MGD-INFRASTRUCT-MIB · .1.3.6.1.4.1.4346.11.11.22.20.1.14

MIB view Table view

Object

scalar r/w Enumeration

Mac-Address assignment method in SCB Mode
disable(0) = Automatic mode. The device adopts the Mac-Address from the connected ethernet device.
enable(1) = Manual mode. Mac-Address is configured by flWorkWlanIf1ScbManMacMode

Context

MIB: FL-MGD-INFRASTRUCT-MIB
OID: .1.3.6.1.4.1.4346.11.11.22.20.1.14
Type: scalar
Access: readwrite
Status: current
Parent: flWorkWlanIf1Parameter
Siblings: 15

Syntax

Enumeration

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects

Object	Type	Syntax	OID
flWorkWlanIf1ParamState State of this interface. It may be enabled or disabled.	scalar	EnabledDisabledStatus	`.1.3.6.1.4.1.4346.11.11.22.20.1.1`
flWorkWlanIf1Fragmentation Set fragmentation thresholds.	scalar	Integer32	`.1.3.6.1.4.1.4346.11.11.22.20.1.10`
flWorkWlanIf1RtsCts Set RTS/CTS values.	scalar	Integer32	`.1.3.6.1.4.1.4346.11.11.22.20.1.11`
flWorkWlanIf1LongDistance Set Parameters for long distance link (meter). This Parameter must be equal at master and station. Normal mode: 3000 meters.	scalar	Integer32	`.1.3.6.1.4.1.4346.11.11.22.20.1.12`
flWorkWlanIf1ScbMacAddress Mac address of the Device in SCB Mode.	scalar	SNMPv2-TCMacAddress	`.1.3.6.1.4.1.4346.11.11.22.20.1.13`
flWorkWlanIf1IAPP 802.11f Inter Accesspoint Protocol (IAPP) disable(0) = IAPP disabled enable(1) = IAPP enabled	scalar	Enumeration	`.1.3.6.1.4.1.4346.11.11.22.20.1.15`
flWorkWlanIf1MachineAdmin	node	-	`.1.3.6.1.4.1.4346.11.11.22.20.1.16`
flWorkWlanIf1ParamOpMode This textual convention is used to distinguish the WIFI operation mode of a device. station: 0 access point (master): 1 single client bridge (scb): 2 multi client bridge (mcb): 3 …	scalar	OpModeType	`.1.3.6.1.4.1.4346.11.11.22.20.1.2`
flWorkWlanIf1ParamSSID SSID (Service Set Identifier) for this interface. An SSID can be up to 32 characters long. Only letters, digits and the special characters: '@!$%&/()=?{}[]+*~#-_.:,;<>' are allowe…	scalar	OctetString	`.1.3.6.1.4.1.4346.11.11.22.20.1.3`
flWorkWlanIf1ParamMode Operation mode of this interface. 1=802.11a, 2=802.11b. 3=802.11b/g, 4=802.11a/n and 5=802.11g/n for master only.	scalar	Enumeration	`.1.3.6.1.4.1.4346.11.11.22.20.1.4`
flWorkWlanIf1ParamChannel Channel of this interface. This depends on your regional limitations and selected wlanMode. -2.4GHz Band ------ Auto (0) Channel-1 (1) Channel-2 (2) Channel…	scalar	Integer32	`.1.3.6.1.4.1.4346.11.11.22.20.1.5`
flWorkWlanIf1ParamOutdoor If this interface is operating in 802.11a mode it must be distinguished between outdoor or indoor operation.	scalar	EnabledDisabledStatus	`.1.3.6.1.4.1.4346.11.11.22.20.1.6`
flWorkWlanIf1AntennaOutput Mask for rx/tx-Antenna X5(1),X6(2),X7(4). e.g. Set (6) to enable x6 and x7 for rx and tx.	scalar	Integer32	`.1.3.6.1.4.1.4346.11.11.22.20.1.7`
flWorkWlanIf1OutputPower Set output power of WLAN interface. Current output power can be lower as defined due to regulatory limitations.	scalar	Integer32	`.1.3.6.1.4.1.4346.11.11.22.20.1.8`
flWorkWlanIf1STBC Set output power of WLAN interface. Current output power can be lower as defined due to regulatory limitations.	scalar	Enumeration	`.1.3.6.1.4.1.4346.11.11.22.20.1.9`