flWorkWlanIf1IAPP
FL-MGD-INFRASTRUCT-MIB ·
.1.3.6.1.4.1.4346.11.11.22.20.1.15
Object
scalar
r/w
Enumeration
802.11f Inter Accesspoint Protocol (IAPP) disable(0) = IAPP disabled enable(1) = IAPP enabled
Context
- MIB
- FL-MGD-INFRASTRUCT-MIB
- OID
.1.3.6.1.4.1.4346.11.11.22.20.1.15- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- flWorkWlanIf1Parameter
- Siblings
- 15
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| flWorkWlanIf1ParamState State of this interface. It may be enabled or disabled. | scalar | EnabledDisabledStatus | .1.3.6.1.4.1.4346.11.11.22.20.1.1 |
| flWorkWlanIf1Fragmentation Set fragmentation thresholds. | scalar | Integer32 | .1.3.6.1.4.1.4346.11.11.22.20.1.10 |
| flWorkWlanIf1RtsCts Set RTS/CTS values. | scalar | Integer32 | .1.3.6.1.4.1.4346.11.11.22.20.1.11 |
| flWorkWlanIf1LongDistance Set Parameters for long distance link (meter). This Parameter must be equal at
master and station. Normal mode: 3000 meters. | scalar | Integer32 | .1.3.6.1.4.1.4346.11.11.22.20.1.12 |
| flWorkWlanIf1ScbMacAddress Mac address of the Device in SCB Mode. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.4346.11.11.22.20.1.13 |
| flWorkWlanIf1ScbManMacMode Mac-Address assignment method in SCB Mode
disable(0) = Automatic mode. The device adopts the Mac-Address from the connected ethernet device.
enable(1) = Manual mode. Mac-Address… | scalar | Enumeration | .1.3.6.1.4.1.4346.11.11.22.20.1.14 |
| flWorkWlanIf1MachineAdmin | node | - | .1.3.6.1.4.1.4346.11.11.22.20.1.16 |
| flWorkWlanIf1ParamOpMode This textual convention is used to distinguish the WIFI operation mode of a device.
station: 0
access point (master): 1
single client bridge (scb): 2
multi client bridge (mcb): 3
… | scalar | OpModeType | .1.3.6.1.4.1.4346.11.11.22.20.1.2 |
| flWorkWlanIf1ParamSSID SSID (Service Set Identifier) for this interface. An SSID can be up to 32 characters long. Only letters, digits and the special characters: '@!$%&/()=?{}[]+*~#-_.:,;<>' are allowe… | scalar | OctetString | .1.3.6.1.4.1.4346.11.11.22.20.1.3 |
| flWorkWlanIf1ParamMode Operation mode of this interface. 1=802.11a, 2=802.11b. 3=802.11b/g, 4=802.11a/n and 5=802.11g/n for master only. | scalar | Enumeration | .1.3.6.1.4.1.4346.11.11.22.20.1.4 |
| flWorkWlanIf1ParamChannel Channel of this interface. This depends on your regional limitations and selected wlanMode.
-2.4GHz Band ------
Auto (0)
Channel-1 (1)
Channel-2 (2)
Channel… | scalar | Integer32 | .1.3.6.1.4.1.4346.11.11.22.20.1.5 |
| flWorkWlanIf1ParamOutdoor If this interface is operating in 802.11a mode it must be distinguished between outdoor or indoor operation. | scalar | EnabledDisabledStatus | .1.3.6.1.4.1.4346.11.11.22.20.1.6 |
| flWorkWlanIf1AntennaOutput Mask for rx/tx-Antenna X5(1),X6(2),X7(4). e.g. Set (6) to enable x6 and x7 for rx and tx. | scalar | Integer32 | .1.3.6.1.4.1.4346.11.11.22.20.1.7 |
| flWorkWlanIf1OutputPower Set output power of WLAN interface. Current output power can be lower as defined due to regulatory limitations. | scalar | Integer32 | .1.3.6.1.4.1.4346.11.11.22.20.1.8 |
| flWorkWlanIf1STBC Set output power of WLAN interface. Current output power can be lower as defined due to regulatory limitations. | scalar | Enumeration | .1.3.6.1.4.1.4346.11.11.22.20.1.9 |