qDeviceVersion

ES-RACKTIVITY-MIB · .1.3.6.1.4.1.34097.9.81.1.1.10151
MIB view Table view

Object

column Version 
The version of the device.

Context

MIB
ES-RACKTIVITY-MIB
OID
.1.3.6.1.4.1.34097.9.81.1.1.10151
Type
column
Access
readonly
Status
current
Parent
eMeasuring3PhaseEntry
Table
eMeasuring3PhaseTable
Siblings
42

Syntax

Version
Source
Version
Base type
OctetString

Values & Constraints

Type Constraints
range: 4

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
qGeneralModuleStatus
General status of a module.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.34097.9.81.1.1.1
qApparentEnergy
Gets the apparent energy used by an outlet. (unit: 0.001kVAh)
columnkVAh Uthousandth.1.3.6.1.4.1.34097.9.81.1.1.10
qStatus
status of a module
columnUnsigned32.1.3.6.1.4.1.34097.9.81.1.1.1000
qModuleName
Gets, sets or defaults the module name.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.81.1.1.10001
qFirmwareVersion
Gets the version of the module's firmware.
columnVersion.1.3.6.1.4.1.34097.9.81.1.1.10002
qHardwareVersion
Gets the version of a module's hardware.
columnVersion.1.3.6.1.4.1.34097.9.81.1.1.10003
qFirmwareID
Gets the ID of the module's firmware.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.81.1.1.10004
qHardwareID
Gets the ID of a module's hardware.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.81.1.1.10005
qPortState
Sets the state of an outlet: 0=OFF, 1=ON, 2=POWER CYCLE. To get the state of an outlet use CPORTSTAT (CLI) or pStatePortCur (SNMP) (GUID 8) instead.
columnUnsigned32.1.3.6.1.4.1.34097.9.81.1.1.10035
qMaxVoltageWarning
Gets, sets or defaults the maximum voltage warning level. (unit: 0.01V)
columnV Unsigned32.1.3.6.1.4.1.34097.9.81.1.1.10047
qMinVoltageWarning
Gets, sets or defaults the minimum voltage warning level. (unit: 0.01V)
columnV Unsigned32.1.3.6.1.4.1.34097.9.81.1.1.10049
qMinTemperatureWarning
Gets, sets or defaults the minimum temperature warning level (use DEF accessor to reset). (unit: 0.1K)
columnK Unsigned32.1.3.6.1.4.1.34097.9.81.1.1.10052
qMaxTemperatureWarning
Gets, sets or defaults the maximum temperature warning level (use DEF accessor to reset). (unit: 0.1K)
columnK Unsigned32.1.3.6.1.4.1.34097.9.81.1.1.10053
qPortStateEvent
Enables or disables the SNMP trap if the state of an outlet is changed.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.81.1.1.10076
qCurrentWarningEvent
Enables or disables the SNMP trap if the outlet current warning level is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.81.1.1.10078
qPowerWarningEvent
Enables or disables the SNMP trap if the power warning level is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.81.1.1.10080
qVoltageWarningEvent
Enables or disables the SNMP trap if the voltage warning level is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.81.1.1.10086
qTemperatureWarningEvent
Enables or disables the SNMP trap if the temperature warning level is exceeded.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.81.1.1.10087
qMicroIntTimeThreshold
The minimum time the voltage must be interrupted before it is seen as a micro interruption (unit: 0.1ms)
columnms Unsigned32.1.3.6.1.4.1.34097.9.81.1.1.10135
qMicroIntEvent
Enables or disables the SNMP trap if a microinterruption on the voltage is detected.
columnEVENTFLAGS.1.3.6.1.4.1.34097.9.81.1.1.10136
qDeviceID
The ID of the device.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.34097.9.81.1.1.10150
qMaxBigCurrentWarning
Gets, sets or defaults the maximum current warning level of an outlet. (unit: 0.0001A)
columnA Unsigned32.1.3.6.1.4.1.34097.9.81.1.1.10193
qMaxBigPowerWarning
Gets, sets or defaults the maximum power warning level of an outlet. (unit: 0.001W)
columnW Unsigned32.1.3.6.1.4.1.34097.9.81.1.1.10194
qCurrentSensorSelector
Selection of the currentsensor connected to port. To enter your own value you need to use 255 and fill in guid 10190.
columnUnsigned32.1.3.6.1.4.1.34097.9.81.1.1.10197
qMinBigCurrentWarning
Gets, sets or defaults the minimum current warning level of a port. (unit: 0.0001A)
columnA Unsigned32.1.3.6.1.4.1.34097.9.81.1.1.10209
qkWhMode
Set the mode when to count kWh, 0 = always, 1 = only positive, 2= only negative
columnUnsigned32.1.3.6.1.4.1.34097.9.81.1.1.10234
qTemperature
Gets the current temperature of a temperature sensor. (unit: 0.1K)
columnK Utenth.1.3.6.1.4.1.34097.9.81.1.1.11
qPowerFactor
Gets the power factor of an outlet. (unit: %)
column% SNMPv2-SMIUnsigned32.1.3.6.1.4.1.34097.9.81.1.1.16
qSpecificModuleStatus
Specific status of a module.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.34097.9.81.1.1.2
qTimeOnline
Gets the amount of seconds since the last reset. (unit: s)
columns SNMPv2-SMIUnsigned32.1.3.6.1.4.1.34097.9.81.1.1.24
qCurrentTime
Gets or sets the current time (not possible when NTP is enabled). (unit: UNIX)
columnUNIX SNMPv2-SMITimeTicks.1.3.6.1.4.1.34097.9.81.1.1.3
qIOPort
Gets the state of a digital input.
columnUnsigned32.1.3.6.1.4.1.34097.9.81.1.1.30
qVoltage
Gets the voltage of a power module. (unit: 0.01V)
columnV Uhundredth.1.3.6.1.4.1.34097.9.81.1.1.4
qFrequency
Gets the frequency of the input voltage of a power module. (unit: 0.001Hz)
columnHz Uthousandth.1.3.6.1.4.1.34097.9.81.1.1.5
qTotalHarmonicDistortion
total harmonic distortion - outlet (unit: 0.1%)
column% Unsigned32.1.3.6.1.4.1.34097.9.81.1.1.50
qPhase
the phase between 2 waves (unit: degr)
columndegr Unsigned32.1.3.6.1.4.1.34097.9.81.1.1.51
qBigCurrent
Gets the current of an outlet. (unit: 0.0001A)
columnA SNMPv2-SMIUnsigned32.1.3.6.1.4.1.34097.9.81.1.1.52
qBigPower
Gets the power of an outlet. (unit: 0.001W)
columnW Uthousandth.1.3.6.1.4.1.34097.9.81.1.1.53
qBigApparentPower
Gets the apparent power of an outlet. (unit: 0.001VA)
columnVA Uthousandth.1.3.6.1.4.1.34097.9.81.1.1.54
measuring3phaseIndex
Index for the selected Measuring3Phase Module
columnInteger32.1.3.6.1.4.1.34097.9.81.1.1.65537
measuring3phaseModuleIndex
Selected Measuring3Phase Module
columnInteger32.1.3.6.1.4.1.34097.9.81.1.1.65538
qActiveEnergy
Gets the energy used by an outlet. (unit: 0.001kWh)
columnkWh Uthousandth.1.3.6.1.4.1.34097.9.81.1.1.9