npInputAnalogStatus – DKSF-PWR-MIB – Observium MIB Browser

Object

column Enumeration

Status of Current Loop Signal,
failure1w = no reply from the adapter on 1wire bus,
failureAnalog = signal is beyond it's Working Range,
belowSafe, safe, aboveSafe - status of the signal 
relative to the Safe Range margins

Context

MIB: DKSF-PWR-MIB
OID: .1.3.6.1.4.1.25728.8200.1.1.2
Type: column
Access: readonly
Status: current
Parent: npInputAnalogEntry
Table: npInputAnalogTable
Siblings: 11

Syntax

Enumeration

Values & Constraints

Enumerated Values

`0`	failure1w
`1`	belowSafe
`2`	safe
`3`	aboveSafe
`5`	failureAnalog

Related Objects

Sibling Objects

Object	Type	Syntax	OID
npInputAnalogSensorN The id of 1Wire Current Loop Adapter, 1 to 5	column	Integer32	`.1.3.6.1.4.1.25728.8200.1.1.1`
npInputAnalogWorkRangeHigh Top marging of Working Range, uA or mV or Ohm. If monitored value is outide of Working Range, Analog Failure take place. If not specified, value is -32768	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.25728.8200.1.1.11`
npInputAnalogSafeRangeHigh Top marging of Safe Range, uA or mV or Ohm. If not specified, value is -32768	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.25728.8200.1.1.12`
npInputAnalogSafeRangeLow Bottom marging of Safe Range, uA or mV or Ohm. If not specified, value is -32768	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.25728.8200.1.1.13`
npInputAnalogWorkRangeLow Bottom marging of Working Range, uA or mV or Ohm. If monitored value is outide of Working Range, Analog Failure take place. If not specified, value is -32768	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.25728.8200.1.1.14`
npInputAnalogCurrent Current via RS_P, RS_N contacts of Current Loop Adapter, uA (microamperes)	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.25728.8200.1.1.3`
npInputAnalogVoltage Voltage on RS_P contact of Current Loop Adapter Vs Ground, mV	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.25728.8200.1.1.4`
npInputAnalogResistance Resistance of the Current Loop, Ohm	column	SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.25728.8200.1.1.5`
npInputAnalogMemo Current Loop memo, what's connected	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.25728.8200.1.1.6`
npInputAnalogPower Controls power on Current Loop Adapter outputs +24V, +12V	column	Enumeration	`.1.3.6.1.4.1.25728.8200.1.1.7`
npInputAnalogReset Write duration 1..25s to temporary switch off +12V, +24V outputs to reset sensor on the current loop by cycling it's power	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.25728.8200.1.1.8`