npInputAnalogPower
DKSF-PWR-MIB ·
.1.3.6.1.4.1.25728.8200.1.1.7
Object
column
r/w
Enumeration
Controls power on Current Loop Adapter outputs +24V, +12V
Context
- MIB
- DKSF-PWR-MIB
- OID
.1.3.6.1.4.1.25728.8200.1.1.7- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- npInputAnalogEntry
- Table
- npInputAnalogTable
- Siblings
- 11
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | off |
1 | on |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| npInputAnalogSensorN The id of 1Wire Current Loop Adapter, 1 to 5 | column | Integer32 | .1.3.6.1.4.1.25728.8200.1.1.1 |
| npInputAnalogWorkRangeHigh Top marging of Working Range, uA or mV or Ohm.
If monitored value is outide of Working Range, Analog Failure take place.
If not specified, value is -32768 | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.25728.8200.1.1.11 |
| npInputAnalogSafeRangeHigh Top marging of Safe Range, uA or mV or Ohm.
If not specified, value is -32768 | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.25728.8200.1.1.12 |
| npInputAnalogSafeRangeLow Bottom marging of Safe Range, uA or mV or Ohm.
If not specified, value is -32768 | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.25728.8200.1.1.13 |
| npInputAnalogWorkRangeLow Bottom marging of Working Range, uA or mV or Ohm.
If monitored value is outide of Working Range, Analog Failure take place.
If not specified, value is -32768 | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.25728.8200.1.1.14 |
| npInputAnalogStatus Status of Current Loop Signal,
failure1w = no reply from the adapter on 1wire bus,
failureAnalog = signal is beyond it's Working Range,
belowSafe, safe, aboveSafe - status of the … | column | Enumeration | .1.3.6.1.4.1.25728.8200.1.1.2 |
| npInputAnalogCurrent Current via RS_P, RS_N contacts of Current Loop
Adapter, uA (microamperes) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.25728.8200.1.1.3 |
| npInputAnalogVoltage Voltage on RS_P contact of Current Loop
Adapter Vs Ground, mV | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.25728.8200.1.1.4 |
| npInputAnalogResistance Resistance of the Current Loop, Ohm | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.25728.8200.1.1.5 |
| npInputAnalogMemo Current Loop memo, what's connected | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.25728.8200.1.1.6 |
| npInputAnalogReset Write duration 1..25s to temporary switch off
+12V, +24V outputs to reset sensor on the
current loop by cycling it's power | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.25728.8200.1.1.8 |