wtSeriNetPckDelay
Com-Server-Intern-MIB ·
.1.3.6.1.4.1.5040.1.1.1.3.4.1.10
Object
column
mandatory
r/w
Integer32
This value indicates the minimum wait time in 10ms ticks of the Com-Server after the arrival of serial data. After this time has expired, it packs the data into a network packet and sends them to the respective communication partner. Default setting 0 means an attempt is made to send the data as quickly as possible. The resulting high time transparency comes with the drawback of a higher number of network packets. If the serial transmission is done in predictable block sizes, adjusting this value will optimize the network load. In addition, there is the advantage that the serial blocks are sent within a network packet and thus reach the recipient at the same time. Please refer also to the Com-Server manual.
Context
- MIB
- Com-Server-Intern-MIB
- OID
.1.3.6.1.4.1.5040.1.1.1.3.4.1.10- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- wtSeriPortEntry
- Table
- wtSeriPortTable
- Siblings
- 8
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-65535
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| wtSeriLocalPort mandatory Local TCP/UDP port number of the Com-Server port on which the Com-Server
accepts a TCP connection or which it used in TCP client mode or UDP mode as a
local port. | column | Integer32 | .1.3.6.1.4.1.5040.1.1.1.3.4.1.1 |
| wtSeriFlushBuf mandatory If this switch is active (2), the serial buffer is flushed each time a
new connection is opened; any residual data which could not be sent (e.g.,
handshake stop of the serial te… | column | Enumeration | .1.3.6.1.4.1.5040.1.1.1.3.4.1.11 |
| wtSeriTelnetEcho mandatory When opening a Telnet connection, there is negotiation on the network
side to determine who generates the echo of the characters sent by the
client. Either the client application … | column | Enumeration | .1.3.6.1.4.1.5040.1.1.1.3.4.1.12 |
| wtSeriPortMode mandatory This parameter specifies the mode of the Com-Server port. Depending
on which mode is set, the corresponding list of the relevant parameters
is available. If for example Upd mode … | column | Enumeration | .1.3.6.1.4.1.5040.1.1.1.3.4.1.2 |
| wtSeriControlPort mandatory TCP port number of the Com-Server's control port. In TCP client or TCP server
mode this port allows to change settings like baud rate, parity etc. of the serial
interface. The c… | column | Integer32 | .1.3.6.1.4.1.5040.1.1.1.3.4.1.3 |
| wtSeriPortState mandatory This value specifies the the connection state of the serial port.
0=Server mode, no connection
1=Server mode, active connection
2=Special mode, attempting to establish a connectio… | column | Enumeration | .1.3.6.1.4.1.5040.1.1.1.3.4.1.4 |
| wtSeriRemotePort mandatory If the serial port has an active TCP or UDP connection, this value shows
the port number of the remote host. | column | Integer32 | .1.3.6.1.4.1.5040.1.1.1.3.4.1.5 |
| wtSeriRemoteIP mandatory If the serial port has an active TCP or UDP connection, this value shows
the IP address of the remote host. | column | RFC1155-SMIIpAddress | .1.3.6.1.4.1.5040.1.1.1.3.4.1.6 |