primarySecondaryMode
CAMBIUM-PTP800-MIB ·
.1.3.6.1.4.1.17713.8.25.3
Object
scalar
r/w
Enumeration
At a given end of a 1+1 Hot Standby configuration, one CMU must be configured as Primary, the other CMU as Secondary. When a Protected Link initialises with no faults, the CMUs configured as Primary will become the Active CMUs, that is, the Primary CMUs are the preferred CMUs. When RFUs are connected to the antenna via an Asymmetric Coupler, the RFU which is connected to the Primary CMU should be connected to the Main path of the coupler. This is the path with the lowest loss.
Context
- MIB
- CAMBIUM-PTP800-MIB
- OID
.1.3.6.1.4.1.17713.8.25.3- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- protectionConfig
- Siblings
- 11
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | primary |
1 | secondary |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| protection PTP 800 supports a 1+1 Hot Standby configuration where
the wireless link is protected against hardware failure.
This requires the installation of redundant equipment at
each en… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.1 |
| fiberY One or both ends of a 1+1 Hot Standby system can be
connected to the network using an 'Optical-Y Splitter Kit
per end'. This end configuration provides a single fiber
interface… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.12 |
| rxDiversityVlanTpid When Receive Diversity is enabled, the Inactive CMU
sends Rx Diversity Ethernet Frames to the Active CMU.
These Ethernet Frames must be VLAN tagged and this
attribute controls … | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.14 |
| rxDiversityVid When Receive Diversity is enabled, the Inactive CMU
sends Rx Diversity Ethernet Frames to the Active CMU.
These Ethernet Frames must be VLAN tagged and this
attribute controls … | scalar | Integer32 | .1.3.6.1.4.1.17713.8.25.15 |
| faultProtectionSwitching In a 1+1 Hot Standby configuration, protection switching
on detection of a fault can be enabled/disabled using
this attribute. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.2 |
| numberOfAntennas This must be configured to match the number of antennas
installed at this end of the link. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.4 |
| primaryRecovery At a given end of a 1+1 Hot Standby configuration, the
CMU configured as Primary is the preferred unit to take
the Active role. If the Primary Recovery attribute is set
to Enab… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.5 |
| primaryRecoveryPeriod At a given end of a 1+1 Hot Standby configuration, the
CMU configured as Primary is the preferred unit to take
the Active role. If the Primary Recovery attribute is set
to Enab… | scalar | Integer32 | .1.3.6.1.4.1.17713.8.25.6 |
| requestedProtectionState In a 1+1 Hot Standby configuration, only one CMU / RFU
at a given end of the link is Active at any one time, the
neighbor CMU / RFU being Inactive. Use the Requested
Protection… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.7 |
| antennaReceiveLevelDeltaThreshold At a given end of a 1+1 Hot Standby configuration, a CMU
will raise an alarm to the management system when the
measured receive level adjusted by antenna gain and
feeder loss i… | scalar | Integer32 | .1.3.6.1.4.1.17713.8.25.8 |
| antennaReceiveLevelMeasurementWindow At a given end of a 1+1 Hot Standby configuration, a CMU
will raise an alarm to the management system when the
measured receive level adjusted by antenna gain and
feeder loss i… | scalar | Integer32 | .1.3.6.1.4.1.17713.8.25.9 |