protectionConfig
CAMBIUM-PTP800-MIB ·
.1.3.6.1.4.1.17713.8.25
Object
node
No description available.
Context
- MIB
- CAMBIUM-PTP800-MIB
- OID
.1.3.6.1.4.1.17713.8.25- Type
- node
- Parent
- ptp800
- Siblings
- 24
- Children
- 12
Syntax
No syntax metadata recorded.
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| phyControl | node | - | .1.3.6.1.4.1.17713.8.10 |
| phyStatus | node | - | .1.3.6.1.4.1.17713.8.12 |
| alarms | node | - | .1.3.6.1.4.1.17713.8.13 |
| smtp | node | - | .1.3.6.1.4.1.17713.8.15 |
| snmpControl | node | - | .1.3.6.1.4.1.17713.8.16 |
| sntp | node | - | .1.3.6.1.4.1.17713.8.17 |
| reset | node | - | .1.3.6.1.4.1.17713.8.18 |
| versions | node | - | .1.3.6.1.4.1.17713.8.19 |
| pubStats | node | - | .1.3.6.1.4.1.17713.8.20 |
| encryption | node | - | .1.3.6.1.4.1.17713.8.22 |
| rfu | node | - | .1.3.6.1.4.1.17713.8.23 |
| radioLicense | node | - | .1.3.6.1.4.1.17713.8.24 |
| protectionStatus | node | - | .1.3.6.1.4.1.17713.8.26 |
| protectionStats | node | - | .1.3.6.1.4.1.17713.8.27 |
| syslogControl | node | - | .1.3.6.1.4.1.17713.8.28 |
| aAAControl | node | - | .1.3.6.1.4.1.17713.8.29 |
| bridge | node | - | .1.3.6.1.4.1.17713.8.4 |
| configuration | node | - | .1.3.6.1.4.1.17713.8.5 |
| ethernet | node | - | .1.3.6.1.4.1.17713.8.6 |
| licence | node | - | .1.3.6.1.4.1.17713.8.8 |
| management | node | - | .1.3.6.1.4.1.17713.8.9 |
| supplementary | node | - | .1.3.6.1.4.1.17713.8.96 |
| ptpGroups | node | - | .1.3.6.1.4.1.17713.8.98 |
| ptpTraps | node | - | .1.3.6.1.4.1.17713.8.99 |
Child Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| protection PTP 800 supports a 1+1 Hot Standby configuration where
the wireless link is protected against hardware failure.
This requires the installation of redundant equipment at
each en… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.1 |
| fiberY One or both ends of a 1+1 Hot Standby system can be
connected to the network using an 'Optical-Y Splitter Kit
per end'. This end configuration provides a single fiber
interface… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.12 |
| rxDiversityVlanTpid When Receive Diversity is enabled, the Inactive CMU
sends Rx Diversity Ethernet Frames to the Active CMU.
These Ethernet Frames must be VLAN tagged and this
attribute controls … | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.14 |
| rxDiversityVid When Receive Diversity is enabled, the Inactive CMU
sends Rx Diversity Ethernet Frames to the Active CMU.
These Ethernet Frames must be VLAN tagged and this
attribute controls … | scalar | Integer32 | .1.3.6.1.4.1.17713.8.25.15 |
| faultProtectionSwitching In a 1+1 Hot Standby configuration, protection switching
on detection of a fault can be enabled/disabled using
this attribute. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.2 |
| primarySecondaryMode At a given end of a 1+1 Hot Standby configuration, one
CMU must be configured as Primary, the other CMU as
Secondary. When a Protected Link initialises with no
faults, the CMUs… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.3 |
| numberOfAntennas This must be configured to match the number of antennas
installed at this end of the link. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.4 |
| primaryRecovery At a given end of a 1+1 Hot Standby configuration, the
CMU configured as Primary is the preferred unit to take
the Active role. If the Primary Recovery attribute is set
to Enab… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.5 |
| primaryRecoveryPeriod At a given end of a 1+1 Hot Standby configuration, the
CMU configured as Primary is the preferred unit to take
the Active role. If the Primary Recovery attribute is set
to Enab… | scalar | Integer32 | .1.3.6.1.4.1.17713.8.25.6 |
| requestedProtectionState In a 1+1 Hot Standby configuration, only one CMU / RFU
at a given end of the link is Active at any one time, the
neighbor CMU / RFU being Inactive. Use the Requested
Protection… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.25.7 |
| antennaReceiveLevelDeltaThreshold At a given end of a 1+1 Hot Standby configuration, a CMU
will raise an alarm to the management system when the
measured receive level adjusted by antenna gain and
feeder loss i… | scalar | Integer32 | .1.3.6.1.4.1.17713.8.25.8 |
| antennaReceiveLevelMeasurementWindow At a given end of a 1+1 Hot Standby configuration, a CMU
will raise an alarm to the management system when the
measured receive level adjusted by antenna gain and
feeder loss i… | scalar | Integer32 | .1.3.6.1.4.1.17713.8.25.9 |