channelALoopbackTrap
CAMBIUM-PTP600-MIB ·
.1.3.6.1.4.1.17713.6.99.0.6
Object
notification
The loopback status of telecoms channel A. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Context
- MIB
- CAMBIUM-PTP600-MIB
- OID
.1.3.6.1.4.1.17713.6.99.0.6- Type
- notification
- Status
- current
- Parent
- ptpTrapPrefix
- Siblings
- 29
Syntax
No syntax metadata recorded.
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| channelChangeTrap The PTP radio has changed wireless channel.
This has been caused by either
i) mandatory radar avoidance,
a DFS impulsive interference event will also be
detected,
or
ii) Dyn… | notification | - | .1.3.6.1.4.1.17713.6.99.0.1 |
| installArmStateTrap Indicates if the unit is being installed. NB: a change
of state may generate an SNMP trap and/or SMTP email
alert | notification | - | .1.3.6.1.4.1.17713.6.99.0.10 |
| unitOutOfCalibrationTrap The unit is out of calibration | notification | - | .1.3.6.1.4.1.17713.6.99.0.11 |
| incompatibleRegionCodesTrap The master and slave units have incompatible region
codes. NB: Both units must have compatible license keys | notification | - | .1.3.6.1.4.1.17713.6.99.0.14 |
| noWirelessChannelAvailableTrap Spectrum Management was unable to locate a suitable
wireless channel to operate on | notification | - | .1.3.6.1.4.1.17713.6.99.0.15 |
| wirelessLinkDisabledWarningTrap The SNMP ifAdminStatus of the wireless interface has
disabled wireless traffic | notification | - | .1.3.6.1.4.1.17713.6.99.0.16 |
| dataPortDisabledWarningTrap The SNMP ifAdminStatus of the Ethernet interface has
disabled Ethernet traffic | notification | - | .1.3.6.1.4.1.17713.6.99.0.17 |
| dataPortFiberStatusTrap If the fiber link is not OK, there are three possible
causes: Either the fiber link has been installed but
disabled (because the license key does not include fiber
support), th… | notification | - | .1.3.6.1.4.1.17713.6.99.0.18 |
| dataPortConfigurationMismatchTrap The detection of Ethernet fragments (runt packets) when
the link is in full duplex is an indication of an
auto-negotiation or forced configuration mismatch | notification | - | .1.3.6.1.4.1.17713.6.99.0.19 |
| dfsImpulsiveInterferenceTrap DFS impulsive interference detected event | notification | - | .1.3.6.1.4.1.17713.6.99.0.2 |
| incompatibleMasterAndSlaveTrap A non-zero value indicates that the master and slave
ends of a link are different hardware products, or have
different software versions. NB: It is very unusual to
detect this,… | notification | - | .1.3.6.1.4.1.17713.6.99.0.20 |
| sNTPSyncTrap If SNTP Sync fails then check the server settings in the
Remote Management page, or disable SNTP | notification | - | .1.3.6.1.4.1.17713.6.99.0.21 |
| tDDSynchronizationAlarmTrap Not Synchronized indicates failure of the external
timing system for a period greater than the holdover
timer. TDD frame timing will have drifted, and this link
may cause inter… | notification | - | .1.3.6.1.4.1.17713.6.99.0.22 |
| managementPortStatusTrap Current status of the out-of-band management link. NB: a
change of state may generate an SNMP trap and/or SMTP
email alert | notification | - | .1.3.6.1.4.1.17713.6.99.0.23 |
| managementPortDisabledWarningTrap The SNMP ifAdminStatus of the out-of-band management
interface has disabled Ethernet traffic | notification | - | .1.3.6.1.4.1.17713.6.99.0.24 |
| linkModeOptimizationMismatchTrap The remote node of this link has been configured with a
different link mode optimization | notification | - | .1.3.6.1.4.1.17713.6.99.0.25 |
| managementPortConfigurationMismatchTrap The detection of Ethernet fragments (runt packets) when
the link is in full duplex is an indication of an
auto-negotiation or forced configuration mismatch. This
alarm is only … | notification | - | .1.3.6.1.4.1.17713.6.99.0.28 |
| dataPortStatusTrap Current status of the Ethernet link. NB: a change of
state may generate an SNMP trap and/or SMTP email alert | notification | - | .1.3.6.1.4.1.17713.6.99.0.3 |
| syslogStateTrap The syslog service has been enabled or disabled | notification | - | .1.3.6.1.4.1.17713.6.99.0.30 |
| syslogLocalNearlyFullTrap The syslog local log is nearly full (90%) | notification | - | .1.3.6.1.4.1.17713.6.99.0.31 |
| syslogLocalWrappedTrap The syslog local log has wrapped | notification | - | .1.3.6.1.4.1.17713.6.99.0.32 |
| syslogClientTrap Enable or disable the syslog client | notification | - | .1.3.6.1.4.1.17713.6.99.0.33 |
| secureModeAlarmTrap The secure mode (e.g. FIPS, UC-APL) state of the unit.
The secure mode is not configured(1) state indicates that
the unit is capable of secure mode operation, and one or
more o… | notification | - | .1.3.6.1.4.1.17713.6.99.0.34 |
| ethernetBridgingStatusAlarmTrap Ethernet traffic bridging is disabled because the
wireless link is not operating at the configured Lowest
Ethernet Modulation Mode | notification | - | .1.3.6.1.4.1.17713.6.99.0.35 |
| telecomsChannelAStatusTrap Current status of telecoms channel A. NB: a change of
state may generate an SNMP trap and/or SMTP email alert | notification | - | .1.3.6.1.4.1.17713.6.99.0.4 |
| telecomsChannelBStatusTrap Current status of telecoms channel B. NB: a change of
state may generate an SNMP trap and/or SMTP email alert | notification | - | .1.3.6.1.4.1.17713.6.99.0.5 |
| channelBLoopbackTrap The loopback status of telecoms channel B. This is
intended for installation testing and should be set to
'None' for normal operation. The wire connections to a
unit can be tes… | notification | - | .1.3.6.1.4.1.17713.6.99.0.7 |
| regionCodeTrap The region code prohibits the wireless unit from
operating outside the regulated limits. An invalid region
code indicates a corrupted license key. NB: a change of
state may gen… | notification | - | .1.3.6.1.4.1.17713.6.99.0.8 |
| installStatusTrap A non-zero value indicates that signalling was received
with the wrong MAC address or a mismatched link name. NB:
It is very unusual to detect this, because units with
mis-conf… | notification | - | .1.3.6.1.4.1.17713.6.99.0.9 |
Notification Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| channelALoopback The loopback status of telecoms channel A. This is
intended for installation testing and should be set to
'None' for normal operation. The wire connections to a
unit can be tes… | scalar | Enumeration | .1.3.6.1.4.1.17713.6.7.8 |