aluPortEtherIngressRateCbs
ALU-PORT-MIB ·
.1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.17
Object
column
r/w
bytes Unsigned32
aluPortEtherIngressRateCbs specifies the committed burst size that hard policer can accept while complying
to the ingress rate tmnxPortEtherIngressRate of the port.
aluPortEtherIngressRateCbs is not applicable when tmnxPortEtherIngressRate is -1.
Setting tmnxPortEtherIngressRate to -1 causes aluPortEtherIngressRateCbs of the port
to revert back to its default value.
aluPortEtherIngressRateCbs must be configured in multiples of 256 bytes.
Context
- MIB
- ALU-PORT-MIB
- OID
.1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.17- Type
- column
- Access
- readwrite
- Status
- current
- Units
- bytes
- Parent
- aluExtTmnxPortEtherEntry
- Table
- aluExtTmnxPortEtherTable
- Siblings
- 28
Syntax
bytes Unsigned32
Values & Constraints
Object Constraints
range: 1-130816
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| aluExtPortEtherSfpSyncEStatus The value of aluExtPortEtherSfpSyncEStatus indicates whether or not
the SFP installed in the port is capabable of supporting synchronous
Ethernet (syncE) communications.
… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.1 |
| aluExtPortEtherLoopbackSwapMacAddr This variable indicates if Source and Destination MAC addresses in the packets are to be
interchanged before being loopbacked to the sender. Setting aluExtPortEtherLoopbackSwapMa… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.10 |
| aluExtPortEtherAdminPhyTxClock The value of aluExtPortEtherAdminPhyTxClock indicates the mode
used to establish timing control of a 1000BASE-T port. The
aluExtPortEtherAdminPhyTxClock is used to control the se… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.11 |
| aluExtPortEtherOperPhyTxClock The value of aluExtPortEtherOperPhyTxClock indicates the operational
value of the MASTER-SLAVE Configuration Resolution bit of register 10
from Table 40-3 of IEEE 802.3-2008. When… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.12 |
| aluEthPtpTimestampCapable The aluEthPtpTimestampCapable indicates whether
the hardware is capable of supporting 1588 PTP time stamp
functions. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.13 |
| aluEthPtpTimestampEnable the aluEthPtpTimestampEnable attribute indicate whether
the port is enabled to support 1588 PTP edge time stamp
functions. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.14 |
| aluEthPtpAsymmetry obsolete aluEthPtpAsymmetry is a path asymmetry correction value
that is used to specify the difference in transmission time
between master-to-slave and slave-to-master. The value
can be … | column | nanoseconds Integer32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.15 |
| aluExtPortEtherLoopbackPersist Setting this variable to 'true' indicates the configuration of aluExtPortEtherLoopback,
aluExtPortEtherLoopbackPersist, aluExtPortEtherLoopbackSwapMacAddr can be saved
to persist… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.16 |
| aluPortEtherIngressRateSrcPause aluPortEtherIngressRateSrcPause indicates whether to send a pause frame for every dropped packet
by the hard policer when tmnxPortEtherIngressRate is > 0.
aluPortE… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.18 |
| aluPortEtherXorMode The aluPortEtherXorMode variable specifies the type of physical connector
for MDA ports which support configurable connector type. aluPortEther
must be 'notApplicable' if the MDA … | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.19 |
| aluExtPortEtherLoopback aluExtPortEtherLoopback is used to put an ethernet port into a loopback mode.
Setting aluExtPortEtherLoopback must be accompanied by setting aluExtPortEtherLoopbackTimer
for the s… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.2 |
| aluPortEtherEgrUnshapedSapCir The value of aluPortEtherEgrUnshapedSapCir specifies the egress CIR of all unshaped SAPs,
i.e. all SAPs using this port that have aluSapEgressSchedulerMode in 4-priority-mode. | column | kbps Integer32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.20 |
| aluExtPortEtherVlanFilter aluExtPortEtherVlanFilter specifies the VLAN filter provisioned for bridge ethernet
ports. The value -1 indicates that no VLAN filter is configured. | column | Integer32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.21 |
| aluExtPortEtherCfmLbVlanList The aluExtPortEtherCfmLbVlanList is an OCTET STRING in which a list of Vlan Ids to be enabled for cfm Loopback when
aluExtPortEtherLoopbackCfmLbMode is priority-dot1p.
… | column | OctetString | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.22 |
| aluExtPortEtherAccEgrShaper aluExtPortEtherNetEgrShaper contains the access egress shaper policy if the tmnxPortMode is hybrid.
Otherwise this object has no significance. | column | TIMETRA-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.23 |
| aluExtPortEtherNetEgrShaper aluExtPortEtherNetEgrShaper contains the network egress shaper policy if the tmnxPortMode is hybrid.
Otherwise this object has no significance. | column | TIMETRA-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.24 |
| aluPortEtherEgrUnshapedNwIfCir The value of aluPortEtherEgrUnshapedNwIfCir specifies the egress CIR of all unshaped network interfaces
on this port, i.e. those network interfaces on this port without a network… | column | kbps Integer32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.25 |
| aluExtPortEtherEgrRateIncludeFCS This variable indicates if the value of tmnxPortEtherEgressRate of the port includes 4 bytes
of ethernet frame check sequence (FCS). | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.26 |
| aluPortEtherOperXorMode The aluPortEtherOperXorMode specifies the type of physical connector used
when MDA ports are configured as auto xor mode. aluPortEtherOperXorMode
must be 'notApplicable' if the MD… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.27 |
| aluExtPortEtherBnAllowed The aluExtPortEtherBnAllowed allows the handling of the received ETH-BN to be processed,
and possibly to enforce the bandwidth indicated in the ETH-BN by changing the egress-rate
… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.28 |
| aluExtPortEtherBnHoldTime aluExtPortEtherBnHoldTime is the time interval to hold aluExtPortEtherBnEgressRateInUse
when changed. This guards against excessive rate changes.
aluExtPortEtherBn… | column | seconds Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.29 |
| aluExtPortEtherLoopbackTimer aluExtPortEtherLoopbackTimer is used to specify the time duration, in seconds, to set the ethernet port
into a loopback mode. Setting aluExtPortEtherLoopbackTimer to a non-zero v… | column | Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.3 |
| aluExtPortEtherLoopbackTimeLeft aluExtPortEtherLoopbackTimeLeft is used to specify the number of seconds left since the loopback has started.
0 if aluExtPortEtherLoopbackTimer was assigned 0, or when aluExtPortE… | column | Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.4 |
| aluExtPortEtherNwSchedulerMode The value of aluExtPortEtherNwSchedulerMode indicates the mode that the
egress scheduler is provisioned to operate in.
profile - Basic in/out scheduling
four… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.5 |
| aluExtPortEtherLoopbackCfmLbMode aluExtPortEtherLoopbackCfmLbMode is to enable/disable an ethernet port to reply to an ethernet CFM
Loopback Message (LBM) frame at the port level. If enabled then it indicates th… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.6 |
| aluExtPortEtherCfmLbmRx aluExtPortEtherCfmLbmRx indicates the received number of Ethernet
CFM Loopback messages (ETH-LBM) with destination MAC address matches
tmnxPortMacAddress of this port, while aluE… | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.7 |
| aluExtPortEtherCfmLbmDropped aluExtPortEtherCfmLbmDropped indicates the number of received, but
discarded Ethernet CFM Loopback messages (ETH-LBM) at this port
while its aluExtPortEtherLoopbackCfmLbMode is en… | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.8 |
| aluExtPortEtherCfmLbrTx aluExtPortEtherCfmLbrTx indicates the number of Ethernet CFM
Loopback Replies (ETH-LBR) that were sent back to the sender, in reponding to the
received ETH-LBM at this port while … | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.2.1.9 |