radioEquipLinkId
ALFOPLUS-SIAE-MIB ·
.1.3.6.1.4.1.3373.25.15.2.1.9
Object
column
r/w
Integer32
Link Identification (value 0..255).
Context
- MIB
- ALFOPLUS-SIAE-MIB
- OID
.1.3.6.1.4.1.3373.25.15.2.1.9- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- radioEquipRecord
- Table
- radioEquipTable
- Siblings
- 46
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| radioEquipId It identify the radio in 1+0 or 1+1 configuration. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.1 |
| radioEquipTxPwrThresh Threshold (value +3 , +15 dB) relative to nominal value of the TX power
below wich the related alarm is set. | column | Integer32 | .1.3.6.1.4.1.3373.25.15.2.1.10 |
| radioEquipRxPwrThresh Threshold (value -40, -99 dBm) for RX power below wich the related
alarm is set. | column | Integer32 | .1.3.6.1.4.1.3373.25.15.2.1.11 |
| radioEquipQualityLowRxSw Enable radioBranchRxQualityLowAlarm as switching criterion
(only if 1+1 configuration) | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.13 |
| radioEquipToProtectStatus Radio branch status towards protection ALFO. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.14 |
| radioEquipToProtectForcedStatus Radio branch forced status towards protection ALFO. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.15 |
| radioEquipFromProtectStatus Protection ALFO radio branch acquired status. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.16 |
| radioEquipProtectRealign Protection unit re-provisioning command start. Value automatically cleared after realign. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.17 |
| radioEquipProtectNotRespondingAlarm Protection unit unreachable alarm status and severity. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.18 |
| radioEquipProtectMismatchAlarm Protection unit not provisioned alarm status and severity. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.19 |
| radioEquipLabel ASCII string used to assign a name to the radio side. | column | OctetString | .1.3.6.1.4.1.3373.25.15.2.1.2 |
| radioEquipLinkTelemetryFailAlarm Fail of link telemetry communication channel with associated severity. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.20 |
| radioEquipLinkIdAlarm Link Identification Alarm with associated Severity. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.21 |
| radioEquipReducedCapacityAlarm The equipment works in reduced capacity. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.22 |
| radioEquipAcmRxProfileInUse This object reports the ACM profile number in use in the radio Rx. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.23 |
| radioEquipAcmTxProfileInUse This object reports the ACM profile number in use in the radio Tx. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.24 |
| radioEquipCurrentTxETHCapacity This object reports the transmitted payload capacity used by the Ethernet. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3373.25.15.2.1.25 |
| radioEquipLowerModulation The object is used to limit the TX modulation at the value set. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.26 |
| radioEquipCurrentRxETHCapacity This object reports the received payload capacity used by the Ethernet. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3373.25.15.2.1.27 |
| radioEquipForceLocalTxProfile This object forces the specified Tx profile on the local terminal.
This is a manual operation. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.28 |
| radioEquipForceRemoteTxProfile This object forces the specified Tx profile on the remote terminal.
This is a manual operation. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.29 |
| radioEquipBandwidthAndModulation Link Modulation and Bandwidth (channel spacing).
The value of this object value is computed by:
16*bandwidth+modulation
where bandwidth is:
1 = 7MHz
2 = 14MHz
3 = 28M… | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.3 |
| radioEquipTxPowerMode This object contains the mode of transmission of RF power used on
changes of modulations. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.30 |
| radioEquipDownshiftOffsetAcm The object sets the offset respect the downshift threshold
for ACM profiles in dB/10. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3373.25.15.2.1.31 |
| radioEquipUpshiftOffsetAcm The object shows the offset respect the upshift threshold
for ACM profiles in dB/10. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3373.25.15.2.1.32 |
| radioEquipSyncEnable It enable the synchronization feature | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.33 |
| radioEquipBerStart Stop, Start (resetting errors and counters) the pattern.
This item is linked to a manual operation (ManOpRecord) instance. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.34 |
| radioEquipBerErrorCounterH 64Bit error counter. Bit 32-63. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.3373.25.15.2.1.35 |
| radioEquipBerErrorCounterL 64Bit error counter. Bit 0-31. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.3373.25.15.2.1.36 |
| radioEquipBerDataCounterH 64Bit data counter. Bit 32-63. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.3373.25.15.2.1.37 |
| radioEquipBerDataCounterL 64Bit data counter. Bit 0-31. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.3373.25.15.2.1.38 |
| radioEquipBerSyncLossAlarm BER sync loss alarm. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.39 |
| radioEquipUpperModulation The object is used to limit the TX modulation at the value set. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.4 |
| radioEquipBerSyncLossAlarmCounter BER sync loss events counter. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3373.25.15.2.1.40 |
| radioEquipBerElapsedTime BER measure elapsed time. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3373.25.15.2.1.41 |
| radioEquipRSSIEnable It enable the RSSI feature | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.42 |
| radioEquipRescueConnectionEnable It enable the rescue connection feature | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.43 |
| radioEquipScanningStartCmd It enable the scanning start feature | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.44 |
| radioEquipScanningFreqMin It define the scanning min frequency (KHz) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3373.25.15.2.1.45 |
| radioEquipScanningFreqMax It define the scanning max frequency (KHz) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3373.25.15.2.1.46 |
| radioEquipScanningFreqStep It define the scanning step frequency (KHz) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3373.25.15.2.1.47 |
| radioEquipScanningFreqTime It define the scanning time frequency (sec) | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3373.25.15.2.1.48 |
| radioEquipScanningPercentageProgress It define the percentage of the scanning measurement | column | Integer32 | .1.3.6.1.4.1.3373.25.15.2.1.49 |
| radioEquipAcmEngineMode This object is used to set the ACM engine. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.5 |
| radioEquipScanningStatus Status of SW download operation. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.50 |
| radioEquipAcmConstantPeakModeEnable This object is used to enable/disable the constant peak power in
the transmitter rf. This mode is used if lowest modulation is
selected as reference. | column | Enumeration | .1.3.6.1.4.1.3373.25.15.2.1.6 |