dsx1TxClockSource

ACE2002-MIB · .1.3.6.1.4.1.164.3.1.6.4.2.1.11

MIB view Table view

Object

column r/w Enumeration

The source of Transmit Clock.
'loopTiming' indicates that the recovered receive clock 
 is used as the transmit clock.
              
'localTiming' indicates that a local clock
 source is used or when an external clock is
 attached to the box containing the interface.
              
'throughTiming' indicates that recovered receive clock 
 from another interface is used as the transmit clock.
               
'adaptive' indicates that the clock is recovered according
 to the received data flow rate.

Context

MIB: ACE2002-MIB
OID: .1.3.6.1.4.1.164.3.1.6.4.2.1.11
Type: column
Access: readwrite
Status: current
Parent: dsx1XConfigEntry
Table: dsx1XConfigTable
Siblings: 17

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	loopTiming
`2`	localTiming
`3`	throughTiming
`4`	adaptive

Related Objects

Sibling Objects

Object	Type	Syntax	OID
dsx1IdleCode Byte pattern of the data received/transmitted in the E1T1 framer idle timeslots. Valid range: (0 - FF HEX).	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.1`
dsx1LineAdaptiveTimingMode Enables end to end clock synchronization. Default value - off.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.10`
dsx1AisEnable Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected).	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.12`
dsx1TsEchoCancel This parameter defines for each TS whether Echo-Cancellation is on. Each bit represents one TS as follow: First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,.., …	column	OctetString	`.1.3.6.1.4.1.164.3.1.6.4.2.1.13`
dsx1EchoCancelerModule This parameter indicates whether echo-cancellation module exists for this line.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.14`
dsx1PortFunction This object determines the ATM Mode over the physical port. uni - The port will function as an ATM UNI. ces - The port will function as a CES. ima - The port will function as a…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.15`
dsx1PortMultiplier This object determines the data rate of each TS (Kbps units). This parameter is applicable for T1 only.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.16`
dsx1LeasedLine This parameter defines whether Line mode is regular (non Leased Line mode) or transparent (Leased Line mode).	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.17`
dsx1CsuLoop This parameter defines whether CSU loop will be done locally (by IPmux) or will be transferred to the TDM device.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.18`
dsx1LineMode T1 device operation mode. Valid for T1 only.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.2`
dsx1dBTxGain Transmit line Gain for T1 CSU line mode.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.3`
dsx1RxSensitivity Determine the maximum attenuation of the receive signal that can be compensated for by the interface receive path. Not applicable for T1.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.4`
dsx1RestoreTime Used to change the sync. algorithms to reduce the time required for the port to return to normal operation after a RED alarm.	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.5`
dsx1TcFirstSignal Trunk conditioning signal - value to be sent as a signal during the first 2.5 seconds after alarm detection. Range is 0x0..0xF. 0xFF is a NULL value. Valid for T1 only.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.6`
dsx1TcSignal Trunk conditioning signal value after alarm detection. Range is 0x1..0xF for E1, and 0x0..0xF for T1.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.7`
dsx1TcPattern Trunk conditioning data pattern to be sent upon a DS0 fail. Range is 0x0..0xFF.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.164.3.1.6.4.2.1.8`
dsx1Scramble Scrambling is an operation that randomizes the bits of the payload of the ATM cell by a polynom. This operation helps with the error detection mechanism of the HEC. Not applicabl…	column	Enumeration	`.1.3.6.1.4.1.164.3.1.6.4.2.1.9`