dsx1LineAdaptiveTimingMode
ACE2002-MIB ·
.1.3.6.1.4.1.164.3.1.6.4.2.1.10
Object
column
r/w
Enumeration
Enables end to end clock synchronization. Default value - off.
Context
- MIB
- ACE2002-MIB
- OID
.1.3.6.1.4.1.164.3.1.6.4.2.1.10- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- dsx1XConfigEntry
- Table
- dsx1XConfigTable
- Siblings
- 17
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | off |
2 | on |
Object Constraints
range: 1-255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| dsx1IdleCode Byte pattern of the data received/transmitted in the
E1T1 framer idle timeslots.
Valid range: (0 - FF HEX). | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.4.2.1.1 |
| dsx1TxClockSource The source of Transmit Clock.
'loopTiming' indicates that the recovered receive clock
is used as the transmit clock.
'localTiming' indicates that a local clock
s… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.11 |
| dsx1AisEnable Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected). | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.12 |
| dsx1TsEchoCancel This parameter defines for each TS whether Echo-Cancellation is on.
Each bit represents one TS as follow:
First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,.., … | column | OctetString | .1.3.6.1.4.1.164.3.1.6.4.2.1.13 |
| dsx1EchoCancelerModule This parameter indicates whether echo-cancellation module
exists for this line. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.14 |
| dsx1PortFunction This object determines the ATM Mode over the
physical port.
uni - The port will function as an ATM UNI.
ces - The port will function as a CES.
ima - The port will function as a… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.15 |
| dsx1PortMultiplier This object determines the data rate of each TS
(Kbps units).
This parameter is applicable for T1 only. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.16 |
| dsx1LeasedLine This parameter defines whether Line mode is regular (non Leased Line mode)
or transparent (Leased Line mode). | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.17 |
| dsx1CsuLoop This parameter defines whether CSU loop will be done locally (by IPmux)
or will be transferred to the TDM device. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.18 |
| dsx1LineMode T1 device operation mode.
Valid for T1 only. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.2 |
| dsx1dBTxGain Transmit line Gain for T1 CSU line mode. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.3 |
| dsx1RxSensitivity Determine the maximum attenuation of the
receive signal that can be compensated for
by the interface receive path. Not applicable for T1. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.4 |
| dsx1RestoreTime Used to change the sync. algorithms to reduce the time
required for the port to return to normal operation after
a RED alarm. | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.5 |
| dsx1TcFirstSignal Trunk conditioning signal - value to be sent as a signal
during the first 2.5 seconds after alarm detection.
Range is 0x0..0xF. 0xFF is a NULL value. Valid for T1 only. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.4.2.1.6 |
| dsx1TcSignal Trunk conditioning signal value after alarm detection.
Range is 0x1..0xF for E1, and 0x0..0xF for T1. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.4.2.1.7 |
| dsx1TcPattern Trunk conditioning data pattern to be sent upon a DS0 fail.
Range is 0x0..0xFF. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.1.6.4.2.1.8 |
| dsx1Scramble Scrambling is an operation that randomizes the bits
of the payload of the ATM cell by a polynom.
This operation helps with the error detection mechanism
of the HEC. Not applicabl… | column | Enumeration | .1.3.6.1.4.1.164.3.1.6.4.2.1.9 |