SUPERMICRO-ISS-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
18
Rows
18
Columns
126

issConfigCtrlTable

table
.1.3.6.1.4.1.10876.101.1.81.2.1 · 1 row entry · 4 columns
Open in standard view 
A table to control device features like egress traffic control,
stats collection, etc. either for the entire switch or for each
interface in the switch.
issConfigCtrlEntry entry .1.3.6.1.4.1.10876.101.1.81.2.1.1
An entry appears in this table for each interface in the system.

In addition to that an entry with index '0' is created in this
table by default.

If 'issConfigCtrlStatus' of the entry '0' is ma…
Indexes
issConfigCtrlIndex
Column Syntax OID
issConfigCtrlIndex
Interface index of the port for which the configuration
in this entry applies.

If any configuration is made in this table for the index '0',
that configuration will be considered as global configuration
…
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.10876.101.1.81.2.1.1.1
issConfigCtrlEgressStatus
Controls the transmission of egress traffic over this interface.

This value for entry '0' controls the egress traffic over all
interfaces.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.81.2.1.1.2
issConfigCtrlStatsCollection
Enables or disables statistics collection for this interface.

This value for entry '0' controls the stats collection for all
interfaces.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.81.2.1.1.3
issConfigCtrlStatus
Speficies the validity of the entry.

If the 'Config Control Status' for entry '0' is made 'valid',
then global control is chosen in the system.
It signifies that the values against entry '0' is applicable…
Enumerationr/w
Enumerated Values:
1valid
2invalid
 .1.3.6.1.4.1.10876.101.1.81.2.1.1.4

issPortCtrlTable

table
.1.3.6.1.4.1.10876.101.1.81.2.2 · 1 row entry · 14 columns
Open in standard view 
A table to control the port specific parameters of the device like speed,
duplex mode, etc.
issPortCtrlEntry entry .1.3.6.1.4.1.10876.101.1.81.2.2.1
An entry appears in this table for each interface in the system.

Index to the table is the interface index of the port.
Indexes
issPortCtrlIndex
Column Syntax OID
issPortCtrlIndex
Interface index of the port for which the configuration
in this entry applies.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.81.2.2.1.1
issPortCtrlMode
Speficies the mode in which the speed, duplex modes and flow control
of the interface is determined.

If set as 'auto', the hardware senses speed and negotiates with the port
on the other end of the link …
Enumerationr/w
Enumerated Values:
1auto
2noNegotiation
 .1.3.6.1.4.1.10876.101.1.81.2.2.1.2
issPortCtrlDuplex
Configures interface data transfer mode as full-duplex or half-duplex.

This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'.
If the 'PortCtrlMode' is 'auto', it obtains the value f…
Enumerationr/w
Enumerated Values:
1full
2half
 .1.3.6.1.4.1.10876.101.1.81.2.2.1.3
issPortCtrlSpeed
Configures interface speed.

This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'.
If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware
after negotiating with its pe…
Enumerationr/w
Enumerated Values:
1tenMBPS
2hundredMBPS
3oneGB
4tenGB
5fortyGB
6fiftysixGB
7twentyfivehundredMBPS
8twentyfiveGB
9fiftyGB
10hundredGB
11autoSpeed
 .1.3.6.1.4.1.10876.101.1.81.2.2.1.4
issPortCtrlFlowControl deprecated
Enables / disables flow control for the interface.

This object be configured only if the 'PortCtrlMode' is 'nonegotiation'.
If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware
after negot…
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.10876.101.1.81.2.2.1.5
issPortCtrlRenegotiate
When configured as 'true', restarts autonegotiation on the interface.

Once autonegotiation is restarted, the value of this object reverts
to 'false'.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.10876.101.1.81.2.2.1.6
issPortCtrlMaxMacAddr
Specifies the maximum number of new MAC addresses that can be
learnt over the interface.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.81.2.2.1.7
issPortCtrlMaxMacAction
Specifies the action to be taken when the maximum number of new MAC
addresses that can be learnt over the interface is exceeded.

If the action is 'drop', the packet with new mac address will be
dropped o…
Enumerationr/w
Enumerated Values:
1drop
2purgeLRU
 .1.3.6.1.4.1.10876.101.1.81.2.2.1.8
issPortHOLBlockPrevention
Enables or disables Head-Of-Line Blocking prevention on a port.
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.10876.101.1.81.2.2.1.9
issPortAutoNegAdvtCapBits
A value uniquely identifies the set of capabilities advertised
by the local auto negotiation entity other than the standard
capabilities supported by ifMauAutoNegCapAdvertisedBits.
When this object is needed to be confi…
OctetStringr/w .1.3.6.1.4.1.10876.101.1.81.2.2.1.10
issPortCpuControlledLearning
Enables or disables the CPU controlled learning on a port.
The default behavior is hardware learning. By enabling this object
software learning on that particular port is enabled.

When CPU controlled le…
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.10876.101.1.81.2.2.1.11
issPortMdiOrMdixCap
Specifies the port should be in Auto-Mdix mode or Mdi/Mdix.

Setting the value to `auto` enables the Auto MDIX in the port -
issPortCtrlIndex. This will be effective only when the speed of the
particular p…
Enumerationr/w
Enumerated Values:
1auto
2mdi
3mdix
 .1.3.6.1.4.1.10876.101.1.81.2.2.1.12
issPortCtrlFlowControlMaxRate
Configures the maximum rate (kbps) - a high water mark beyond which
pause frames will be generated to flow control the ingress traffic.
This value should be set to 0 if no pause frame generation is required.
In chipsets…
Integer32r/w
Constraints:
range: 0-80000000
 .1.3.6.1.4.1.10876.101.1.81.2.2.1.13
issPortCtrlFlowControlMinRate
Configures the minimum rate (kbps) - a low water mark below which pause
frames generation will be stopped. This value should be set to a value
lesser that of 'issPortCtrlFlowControlMaxRate'. This value should be set
…
Integer32r/w
Constraints:
range: 0-80000000
 .1.3.6.1.4.1.10876.101.1.81.2.2.1.14

issPortIsolationTable

table
.1.3.6.1.4.1.10876.101.1.81.2.3 · 1 row entry · 5 columns
Open in standard view 
This table is used to configure the port isolation feature.
For a given port, user can configure the list of allowed
forwarding/egress ports, where the packets for particular vlan that 
ingress the port can be forwarded. If the Vlan is not given, then 
the rule will be applied for all packets that ingress the given port.
          
This table can be configured only for physical and link aggregated 
ports. 
          
Before a packet is sent out of a port (after all L2/L3 processing), port 
isolation table entry is referred for the ingress port of that packet. 
If an entry is present for that ingress port and if the outgoing port 
is configured as one of the egress ports , then the packet 
will be transmitted out of that outgoing port. Otherwise the packet 
will be dropped.
          
If there is no entry configured for that ingress port in this
table, then the packet will be transmitted on that outgoing port.
issPortIsolationEntry entry .1.3.6.1.4.1.10876.101.1.81.2.3.1
Each etnry in this table gives a ingress port to egress port mapping.
Indexes
issPortIsolationIngressPort issPortIsolationInVlanId issPortIsolationEgressPort
Column Syntax OID
issPortIsolationIngressPort
This object speficies the IfIndex of the ingress port. This port can
be a physical or link aggregated port.
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.10876.101.1.81.2.3.1.1
issPortIsolationInVlanId
If this object value is non-zero, then the port isolation rule is
applied for all packets received on the given ingress port.
Otherwise the rule is applied for this vlan packets received on the
given ingress port.
Integer32
Constraints:
range: 0-4094
 .1.3.6.1.4.1.10876.101.1.81.2.3.1.2
issPortIsolationEgressPort
This object specifies one of the allowed egress ports for the given
ingress port identified by the first index for this row.
This port can be either a physical or link aggregated port.
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.10876.101.1.81.2.3.1.3
issPortIsolationStorageType
Indicates the storage type of this entry.
Only 'volatile' and 'nonVolatile' values are allowed for this object.
'readOnly', 'permenant' and 'other' values are not allowed for this
object.

If this table …
SNMPv2-TCStorageType
Textual Convention: SNMPv2-TCStorageType Enumeration
Type Values:
1other
2volatile
3nonVolatile
4permanent
5readOnly
 .1.3.6.1.4.1.10876.101.1.81.2.3.1.4
issPortIsolationRowStatus
Denotes the Row Status for port isolation table entry.
Only 'CreateAndGo' and 'destroy' values are allowed for this
object. 'CreateAndWait' and 'notInService' values are not allowed.
Example:
To add ports 2, 3 as egr…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.81.2.3.1.5

issSplitModeTable

table
.1.3.6.1.4.1.10876.101.1.81.2.4 · 1 row entry · 2 columns
Open in standard view 
A table to control the port split mode of the device
issSplitModeEntry entry .1.3.6.1.4.1.10876.101.1.81.2.4.1
An entry appears in this table for each interface in the system.

Index to the table is the interface index of the port.
Indexes
issSplitModeIndex
Column Syntax OID
issSplitModeIndex
Interface index of the port for which the configuration
in this entry applies.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.81.2.4.1.1
issSplitModeValue
Speficies the setting in which split mode of the interface is determined.

If set as 'off', Qx port will be turn on and related Ex ports will be turn off.

If set as 'on', Ex ports will be tu…
Enumerationr/w
Enumerated Values:
0off
1on
2none
 .1.3.6.1.4.1.10876.101.1.81.2.4.1.2

issMirrorCtrlTable

table
.1.3.6.1.4.1.10876.101.1.81.3.3 · 1 row entry · 4 columns
Open in standard view 
A table to control mirroring features for each interface 
in the switch.
          
Parameters in this table are valid only when the 
'issMirrorStatus' for the switch is not 'disabled'.
issMirrorCtrlEntry entry .1.3.6.1.4.1.10876.101.1.81.3.3.1
An entry appears in this table for each interface
in the system.
Indexes
issMirrorCtrlIndex
Column Syntax OID
issMirrorCtrlIndex
The interface index of the port for which the configuration
in this entry applies.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.81.3.3.1.1
issMirrorCtrlIngressMirroring
Provides control to enable or disable mirroring of ingress
traffic over this interface to the mirrored-to port.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.81.3.3.1.2
issMirrorCtrlEgressMirroring
Provides control to enable or disable mirroring of egress
traffic over this interface to the mirrored-to port.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.81.3.3.1.3
issMirrorCtrlStatus
Specifies the validity of the entry.
Enumerationr/w
Enumerated Values:
1valid
2invalid
 .1.3.6.1.4.1.10876.101.1.81.3.3.1.4

issMirrorCtrlExtnTable

table
.1.3.6.1.4.1.10876.101.1.81.3.6 · 1 row entry · 6 columns
Open in standard view 
This Table is used to configure advanced mirroring features like
- Port Based Mirroring:
- flow based mirroring
- vlan based mirroring
          
     Following are the configuration details for Port based mirroring:
         To configure source ports in a session
        - issMirrorCtrlExtnMirrType - is set to portBased
        - issMirrorCtrlExtnSrcTable - should be used to configure list
                                      of source ports to be mirrored 
                                      in a session
        - issMirrorCtrlExtnSrcId  - represents the source port. 
                                    The port Id to be mirrored 
                                    should be given here.
        - issMirrorCtrlExtnSrcCfg - this object is used to 
                                    add/remove a port in the 
                                    source port list 
          
        Example
        To create a session 1 with source ports 5,6 following 
        sequence of configuration should be followed
        For table issMirrorCtrlExtnTable
        issMirrorCtrlExtnSessionIndex = 1 as index
        issMirrorCtrlExtnMirrType = portBased
          
        For table issMirrorCtrlExtnSrcTable
        issMirrorCtrlExtnSessionIndex = 1 as index
        issMirrorCtrlExtnSrcId  = 5 as index
        issMirrorCtrlExtnSrcCfg = add
        issMirrorCtrlExtnSessionIndex = 1 as index
        issMirrorCtrlExtnSrcId  = 6 as index
        issMirrorCtrlExtnSrcCfg = add
                       
        To configure destination ports in a session
         - issMirrorCtrlExtnDestinationTable - should be used to 
                                               configure list of 
                                               destination ports to be 
                                               mirrored in a session
             - issMirrorCtrlExtnDestination  - represents the 
                                               destination port. The 
                                               port Id to which packets 
                                               should be mirrored should
                                               be given here.
             - issMirrorCtrlExtnDestCfg - this object is used to 
                                          add/remove a port in the 
                                          source port list. 
             Example
             To create a session 1 with destination port 10,11 following
             sequence of configuration should be followed
             For table issMirrorCtrlExtnTable
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnMirrType = portBased
          
             For table issMirrorCtrlExtnDestinationTable
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnDestination  = 10 as index
             issMirrorCtrlExtnDestCfg = add
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnDestination  = 11 as index
             issMirrorCtrlExtnDestCfg = add
          
        To Activate a session
         - issMirrorCtrlExtnStatus - should be used to 
                                     activate/deactivate mirroring for a
                                     session
             Example
             To enable mirroring for a session following sequence of 
             configuration should be followed        
             For table issMirrorCtrlExtnTable
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnStatus = active
          
         Above configurations applies to flow based mirroring also, the 
         issMirrorCtrlExtnSrcId used above for configuratin ports 
         should be used to configure flow Id
                   
        To enable remote monitoring of sources for a session
         - issMirrorCtrlExtnRSpanStatus - should be used to 
                                          enable/disable remote 
                                          monitoring for a session 
                                          it can be used to set a 
                                          session as source rspan 
                                          session which implies source 
                                          entities for this session are 
                                          monitored remotely or can be 
                                          used to set a session 
                                          as destination rspan session 
                                          which implies that mirrored 
                                          data is received for this 
                                          session should be forwarded to 
                                          destination entities of this 
                                          session
         - issMirrorCtrlExtnRSpanVlanId - it is the vlan id which is 
                                          reserved in the network to 
                                          carry Mirrored data,if the 
                                          session is configured as 
                                          source rspan session then data 
                                          mirrored for the source 
                                          entities will be forwarded on 
                                          this vlan if the session is 
                                          configured as destination 
                                          rspan session then data 
                                          received on this vlan will be 
                                          forwarded to the destination 
                                          entities of this session
          
     Following are the configuration details for configurating Vlan 
     based mirroring:
         To configure vlans as source for a session
        - issMirrorCtrlExtnMirrType - is set to vlanBased
        - issMirrorCtrlExtnSrcVlanTable - should be used to configure 
                                          list of source vlans to be 
                                          mirrored in a session
          - issMirrorCtrlExtnSrcVlanId  - represents a source vlan. The 
                                          vlan to be mirrored should be 
                                          given here.
          - issMirrorCtrlExtnSrcVlanCfg - this object is used to 
                                          add/remove a vlan in the 
                                          source vlan list 
             Example
             To create a session 1 with source list as vlan 5,6 
             belonging to context 1 following sequence of configuration
             should be followed
             For table issMirrorCtrlExtnTable
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnMirrType = vlanBased
          
             For table issMirrorCtrlExtnSrcVlanTable
             issMirrorCtrlExtnSrcVlanContext = 1 as index
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnSrcVlanId  = 5 as index
             issMirrorCtrlExtnSrcVlanCfg = add
             issMirrorCtrlExtnSrcVlanContext = 1 as index
             issMirrorCtrlExtnSessionIndex = 1 as index
             issMirrorCtrlExtnSrcVlanId  = 6 as index
             issMirrorCtrlExtnSrcVlanCfg = add
                       
Entries for this table can be configured only when issMirrorStatus 
is set to enabled.
Configurations done through 'issMirrorCtrlTable' will change the 
following for the first session on this table:
     - Mirroring type will be changed to port-based
     - Mode and Source entities will be overwritten 
       with the values configured through 'issMirrorCtrlTable'
     - Destination entities will be overwritten 
       with the value configured through 'issMirrorToPort' object
issMirrorCtrlExtnEntry entry .1.3.6.1.4.1.10876.101.1.81.3.6.1
An entry appears in this table for each session
in the system.
Indexes
issMirrorCtrlExtnSessionIndex
Column Syntax OID
issMirrorCtrlExtnSessionIndex
The index of the mirroring session for which the configuration
in this entry applies.
Integer32
Constraints:
range: 1-20
 .1.3.6.1.4.1.10876.101.1.81.3.6.1.1
issMirrorCtrlExtnMirrType
This object tells the type of mirroring this session supports.
This object needs to be set before doing any configuration for
a mirroring session
Enumerationr/w
Enumerated Values:
1portBased
2mac-flowBased
3vlanBased
4invalid
5ip-flowBased
 .1.3.6.1.4.1.10876.101.1.81.3.6.1.2
issMirrorCtrlExtnRSpanStatus
This object indicates session is enabled or disabled for
Remote monitoring.
If set as 'source-rspan-vlanid' indicates that the session is
enabled for Remote monitoring and the source entities for this
session will be…
Enumerationr/w
Enumerated Values:
1sourceRSpanVlan
2destinationRSpanVlan
3disabled
 .1.3.6.1.4.1.10876.101.1.81.3.6.1.3
issMirrorCtrlExtnRSpanVlanId
Vlan Id used for Remote monitoring for this session.
If issMirrorCtrlExtnRSpanStatus is set to disabled, then
this object will have an invalid value (zero)
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.81.3.6.1.4
issMirrorCtrlExtnRSpanContext
Specifies the Context Id to which the RSpan Vlan belongs.
Value '0' mean this object is not considered for this
mirroring session.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.81.3.6.1.5
issMirrorCtrlExtnStatus
This object indicates the status of the entry. The entry can be
made active only if issMirrorCtrlExtnMirrType is configured and
source and destination entries for this sesion is also configured
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.81.3.6.1.6

issMirrorCtrlExtnSrcTable

table
.1.3.6.1.4.1.10876.101.1.81.3.7 · 1 row entry · 3 columns
Open in standard view 
A table to configure list of source entities for mirroring sessions
issMirrorCtrlExtnSrcEntry entry .1.3.6.1.4.1.10876.101.1.81.3.7.1
An entry appears in this table for each mirroring session.
Indexes
issMirrorCtrlExtnSessionIndex issMirrorCtrlExtnSrcId
Column Syntax OID
issMirrorCtrlExtnSrcId
Specifies the source id which participates in a mirroring session.
For Port based mirroring this object can be port IfIndex.
To mirror Tunnel and Trunk ports the same Id can be used for
specifying Tunnel/Trunk Id.
For …
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.81.3.7.1.1
issMirrorCtrlExtnSrcCfg
This object is used to create/delete a source entry for a session.
Enumerationr/w
Enumerated Values:
1add
2delete
 .1.3.6.1.4.1.10876.101.1.81.3.7.1.2
issMirrorCtrlExtnSrcMode
Provides control to set the mode of mirroring.
It can be ingress, egress, both or disable.
Enumerationr/w
Enumerated Values:
1ingress
2egress
3both
4disable
 .1.3.6.1.4.1.10876.101.1.81.3.7.1.3

issMirrorCtrlExtnSrcVlanTable

table
.1.3.6.1.4.1.10876.101.1.81.3.8 · 1 row entry · 4 columns
Open in standard view 
A table to configure list of vlan source entities for mirroring sessions
issMirrorCtrlExtnSrcVlanEntry entry .1.3.6.1.4.1.10876.101.1.81.3.8.1
An entry appears in this table for each mirroring session.
Indexes
issMirrorCtrlExtnSessionIndex issMirrorCtrlExtnSrcVlanContext issMirrorCtrlExtnSrcVlanId
Column Syntax OID
issMirrorCtrlExtnSrcVlanContext
Specifies the Context Id to which the source entity belongs, this
is used in case of specifying vlan as source.
Value '-1' mean this object is not considered for this mirroring
session.
Integer32
Constraints:
range: 1-64
 .1.3.6.1.4.1.10876.101.1.81.3.8.1.1
issMirrorCtrlExtnSrcVlanId
Specifies the Vlan id which participates in a mirroring session.
Integer32
Constraints:
range: 1-4094
 .1.3.6.1.4.1.10876.101.1.81.3.8.1.2
issMirrorCtrlExtnSrcVlanCfg
This object is used to create/delete a vlan entry for a session.
Enumerationr/w
Enumerated Values:
1add
2delete
 .1.3.6.1.4.1.10876.101.1.81.3.8.1.3
issMirrorCtrlExtnSrcVlanMode
Provides control to set the mode of mirroring.
It can be ingerss,Egress or Both.
Enumerationr/w
Enumerated Values:
1ingress
2egress
3both
 .1.3.6.1.4.1.10876.101.1.81.3.8.1.4

issMirrorCtrlExtnDestinationTable

table
.1.3.6.1.4.1.10876.101.1.81.3.9 · 1 row entry · 2 columns
Open in standard view 
A table to configure list of destination entities
issMirrorCtrlExtnDestinationEntry entry .1.3.6.1.4.1.10876.101.1.81.3.9.1
An entry appears in this table for each destination entity
in a mirroring session.
Indexes
issMirrorCtrlExtnSessionIndex issMirrorCtrlExtnDestination
Column Syntax OID
issMirrorCtrlExtnDestination
Specifies the destination port id which participates in a mirroring
session.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.81.3.9.1.1
issMirrorCtrlExtnDestCfg
This object is used to create/delete a destination entry for a session.
Enumerationr/w
Enumerated Values:
1add
2delete
 .1.3.6.1.4.1.10876.101.1.81.3.9.1.2

issRateCtrlTable

table deprecated
.1.3.6.1.4.1.10876.101.1.81.4.1 · 1 row entry · 6 columns
Open in standard view 
A table to control the rate limiting parameters 
either for the entire switch or for each interface in the switch.
This object is deprecated and the corresponding functionality is
met with issRateControl objects in fsissext.mib.
issRateCtrlEntry entry .1.3.6.1.4.1.10876.101.1.81.4.1.1
An entry appears in this table for each physical
interface in the switch.
This object is deprecated and the corresponding functionality is
met with issRateControl objects in fsissext.mib.
Indexes
issRateCtrlIndex
Column Syntax OID
issRateCtrlIndex deprecated
The interface index for which the configuration in this
entry applies.
This object is deprecated and the corresponding functionality is
met with issRateControl objects in fsissext.mib.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.81.4.1.1.1
issRateCtrlDLFLimitValue deprecated
Allows to configure the limiting value for the maximum number
of dlf packets that can be transmitted per second over this interface.
Setting this object to the value zero disables rate limiting for
Destination lookup f…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.10876.101.1.81.4.1.1.2
issRateCtrlBCASTLimitValue deprecated
Allows to configure the limiting value for the maximum number
of broadcast packets that can be transmitted per second over this
interface. Setting this object to the value zero disables rate
limiting for Broadcast pac…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.10876.101.1.81.4.1.1.3
issRateCtrlMCASTLimitValue deprecated
Allows to configure the limiting value for the maximum number
of multicast packets that can be transmitted per second over this
interface. Setting this object to the value zero disables rate
limiting for Multicast pac…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.10876.101.1.81.4.1.1.4
issRateCtrlPortRateLimit deprecated
Configures interface Rate Limit (Packet that can be transferred
on a port at a particular second).

This object's value will take effect on the interface speed. Based
on the operating speed of the port, th…
Integer32r/w
Constraints:
range: 0-80000000
 .1.3.6.1.4.1.10876.101.1.81.4.1.1.5
issRateCtrlPortBurstSize deprecated
Configures interface Burst Pkt Rate. (Packet Burst that can be
transferred on a port at a particular second)

This object's value will take effect on the interface speed. Based
on the operating speed of th…
Integer32r/w
Constraints:
range: 0-80000000
 .1.3.6.1.4.1.10876.101.1.81.4.1.1.6

issL2FilterTable

table deprecated
.1.3.6.1.4.1.10876.101.1.81.5.1 · 1 row entry · 13 columns
Open in standard view 
A table to configure L2 filter rules in the system.
This object is deprecated and the corresponding functionality is
met with issL2Filter objects in fsissext.mib.
issL2FilterEntry entry .1.3.6.1.4.1.10876.101.1.81.5.1.1
Each entry in this table is a L2 filter rule.Index to the table
is the L2 filter number.This object is deprecated and the
corresponding functionality is met with issL2Filter objects
in fsissext.mib.
Indexes
issL2FilterNo
Column Syntax OID
issL2FilterNo
L2 Filter rule number.
This object is deprecated and the corresponding functionality is
met with issL2Filter objects in fsissext.mib.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.81.5.1.1.1
issL2FilterPriority
The priority of the L2 filter can be used to decide which filter rule
is applicable when
--> the packet matches with more than one filter rules
--> All the filter rules result in 'allow'ing the packet
…
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.10876.101.1.81.5.1.1.2
issL2FilterEtherType deprecated
The value in the Type/Len field of a frame that will
be matched to trigger this filter. The default value of
this object is '0'. When this object is SET with the default
value, frames are not matched for the value in th…
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.10876.101.1.81.5.1.1.3
issL2FilterProtocolType deprecated
Specifies the non IP protocol type to be filtered.
aarp | amber | dec-spanning | decnet-iv |
diagnostic | dsm |etype-6000 | etype-8042 |
lat | lavc-sca | mop-console | mop-dump |
msdos | mumps | netbios | vines-echo …
Unsigned32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.10876.101.1.81.5.1.1.4
issL2FilterDstMacAddr deprecated
Destination MAC address to be matched with the packet. By Default, the
Destination Mac Address will be zero which means dont care condition ie)
any Dst Mac Address .This object is deprecated and the corresponding
funct…
SNMPv2-TCMacAddressr/w
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.10876.101.1.81.5.1.1.5
issL2FilterSrcMacAddr deprecated
Source MAC address to be matched with the packet. By Default, the Source
Mac Address will be zero which means dont care condition ie) any Src Mac
address This object is deprecated and the corresponding functionality i…
SNMPv2-TCMacAddressr/w
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.10876.101.1.81.5.1.1.6
issL2FilterVlanId deprecated
Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will
be treated as customer Vlan Id.
A value of '0' means, this object is unused. Configuring this value is not
allowed.
This object is deprecated and t…
Integer32r/w
Constraints:
range: 0-4094
 .1.3.6.1.4.1.10876.101.1.81.5.1.1.7
issL2FilterInPortList deprecated
Specifies the complete set of ports over which this filter is applied
for packets ingress at ports in this list.
If the In port list is '0', the filter rule is applicable for the
incoming packets on all ports.
Even th…
PortListr/w
Textual Convention: PortList OctetString
 .1.3.6.1.4.1.10876.101.1.81.5.1.1.8
issL2FilterAction deprecated
Specifies the action to be taken on the packet if the filter
rule matches.
If the action is 'allow', the packet will be forwarded according
to the forwarding rules.
If the action is 'drop', the packet will be discarded.…
Enumerationr/w
Enumerated Values:
1allow
2drop
 .1.3.6.1.4.1.10876.101.1.81.5.1.1.9
issL2FilterMatchCount deprecated
Number of times this filter is matched.
This object is deprecated and the corresponding functionality is
met with issL2Filter objects in fsissext.mib.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.81.5.1.1.10
issL2FilterStatus deprecated
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.81.5.1.1.11
issL2FilterOutPortList deprecated
Specifies the complete set of ports over which this filter is applied
for packets egress at Ports in this list.
If the Out port list is '0', the filter rule is applicable for the
outgoing packets on all ports.
Even th…
PortListr/w
Textual Convention: PortList OctetString
 .1.3.6.1.4.1.10876.101.1.81.5.1.1.12
issL2FilterDirection deprecated
Specifies the direction of this filter to be applied. By Default the
filter will be applied on ingress direction.
When the direction of this filter is 'in', It is applied on specified
ports of the issL2FilterInPortList.…
Enumerationr/w
Enumerated Values:
1in
2out
 .1.3.6.1.4.1.10876.101.1.81.5.1.1.13

issL3FilterTable

table deprecated
.1.3.6.1.4.1.10876.101.1.81.6.1 · 1 row entry · 23 columns
Open in standard view 
A table to configure L3 filter rules in the system.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib.
issL3FilterEntry entry .1.3.6.1.4.1.10876.101.1.81.6.1.1
Each entry in this table is a L3 filter rule.
Index to the table is L3 filter number.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib.
Indexes
issL3FilterNo
Column Syntax OID
issL3FilterNo deprecated
L3 Filter rule number.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.1
issL3FilterPriority deprecated
The priority of the filter can be used to decide which filter rule
is applicable when
--> the packet matches with more than one filter rules
--> All the filter rules result in 'allow'ing the packet
Higher value o…
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.2
issL3FilterProtocol deprecated
The type of protocol to be checked against the packet. The
default value is 255. If the value is 255, it means that the
protocol type can be anything and it will not be checked to
decide the action.
This object is depr…
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.3
issL3FilterMessageType deprecated
The message type to be checked against the packet. If the
message type matches with the packet, then the packet will be
dropped / allowed based on the action set in issL3FilterAction.
The default value is 255. It means …
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.4
issL3FilterMessageCode deprecated
The message code to be checked against the packet. If the
packet matches with the message code, then the packet will
be dropped / allowed based on the action set in issL3FilterAction.
The default value is 255. It means …
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.5
issL3FilterDstIpAddr deprecated
Destination IP address to be matched with the packet.
This object is valid only if the 'issFilterType' is 'l3filter'.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsis…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.6
issL3FilterSrcIpAddr deprecated
Source IP address to be matched with the packet.
This object is valid only if the 'issFilterType' is 'l3filter'
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.m…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.7
issL3FilterDstIpAddrMask deprecated
The IP subnet mask for Destination IP address.
This object is valid only if the 'issFilterType' is 'l3filter'
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.8
issL3FilterSrcIpAddrMask deprecated
The IP subnet mask for Source IP address.
This object is valid only if the 'issFilterType' is 'l3filter'.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.9
issL3FilterMinDstProtPort deprecated
The minimum port in the destination port range. Please note
these ports are the TCP / UDP ports.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.10
issL3FilterMaxDstProtPort deprecated
The maximum port in the destination port range. Please note
these ports are the TCP / UDP ports.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.11
issL3FilterMinSrcProtPort deprecated
The minimum port in the source port range. Please note
these ports are the TCP / UDP ports.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.12
issL3FilterMaxSrcProtPort deprecated
The maximum port in the source port range. Please note
these ports are the TCP / UDP ports.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.13
issL3FilterInPortList deprecated
Specifies the complete set of ports over which if the packet arrives
this filter rule will be applicable.
If the incoming port list is '0', the filter rule is applicable for all the
incoming ports.
By default inport li…
PortListr/w
Textual Convention: PortList OctetString
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.14
issL3FilterOutPortList deprecated
Specifies the complete set of ports over which if the packet goes out,
this filter rule will be applicable.
If the outgoing port list is '0',the filter rule is applicable for all the
outgoing packets in all ports.
By …
PortListr/w
Textual Convention: PortList OctetString
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.15
issL3FilterAckBit deprecated
The TCP ACK bit to be checked against the packet. The default
value is 'any'(3). It means that ACK bit will not be checked
to decide the action.
This object is deprecated and the corresponding functionality is
met wit…
Enumerationr/w
Enumerated Values:
1establish
2notEstablish
3any
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.16
issL3FilterRstBit deprecated
The TCP RST bit to be checked against the packet. The default
value is 'any'(3). It means that RST bit will not be checked to
decide the action.
This object is deprecated and the corresponding functionality is
met wit…
Enumerationr/w
Enumerated Values:
1set
2notSet
3any
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.17
issL3FilterTos deprecated
The IP TOS bit to be checked against the packet. This is a
single byte integer of which the last three bits (least
significant bits) indicate Delay, Throughput and Reliability
i.e 'uuuuudtr', u-unused, d-delay, t-thr…
Integer32r/w
Constraints:
range: -1-7
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.18
issL3FilterDscp deprecated
The IP Dscp value to be checked against the packet.
A value of '-1' means, the Dscp Field becomes dont care.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib.
Integer32r/w
Constraints:
range: -1-63
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.19
issL3FilterDirection deprecated
Specifies the direction of this filter to be applied. By Default the
filter will be applied on ingress direction.
When the direction of this filter is 'in', It is applied on specified
ports of the issL3FilterInPortList.…
Enumerationr/w
Enumerated Values:
1in
2out
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.20
issL3FilterAction deprecated
Specifies the action to be taken on the packet if the filter
rule matches.
If the action is 'allow', the packet will be sent to the
ports in 'out port list'. If the out port list is '0',
the port over which the packet …
Enumerationr/w
Enumerated Values:
1allow
2drop
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.21
issL3FilterMatchCount deprecated
Number of times this filter is matched.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.22
issL3FilterStatus deprecated
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.81.6.1.1.23

issIpAuthMgrTable

table
.1.3.6.1.4.1.10876.101.1.81.7.1 · 1 row entry · 7 columns
Open in standard view 
A table to configure IP authorized managers in the system.
issIpAuthMgrEntry entry .1.3.6.1.4.1.10876.101.1.81.7.1.1
Each entry in this table represents rules for particular
IP authorized manager.
Indexes
issIpAuthMgrIpAddr issIpAuthMgrIpMask
Column Syntax OID
issIpAuthMgrIpAddr
Specifies either the Network or Host address from which the switch
can be managed.
An address 0.0.0.0 indicates 'Any Manager'.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.81.7.1.1.1
issIpAuthMgrIpMask
Specifies the IP address mask to be applied on issIpAuthMgrIpAddr.
Value 0.0.0.0 indicates mask for 'Any Manager'.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.81.7.1.1.2
issIpAuthMgrPortList
Specifies the port numbers through which the authorized manager can
access the switch.

By default the authorized manager is allowed to access the switch
through all the ports.

If a set of…
PortListr/w
Textual Convention: PortList OctetString
 .1.3.6.1.4.1.10876.101.1.81.7.1.1.3
issIpAuthMgrVlanList
Specifies the Vlan's in which the IP authorized manager can reside.
By default the manager is allowed to reside in any vlan.

If a set of vlans are configured in the 'VlanList', the manager can
reside onl…
OctetStringr/w .1.3.6.1.4.1.10876.101.1.81.7.1.1.4
issIpAuthMgrOOBPort
Specifies whether the authorized manager can access the switch
through OOB Port
By default the manager is denied access to reside on OOB Interface
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.10876.101.1.81.7.1.1.5
issIpAuthMgrAllowedServices
Specifies the allowed services through which the authorized manager can
access the switch.
This object takes bit mask values. The services represented by each bit
position is as given below:

With bi…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.81.7.1.1.6
issIpAuthMgrRowStatus
This object indicates the status of this entry.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.81.7.1.1.7

issL4SwitchingFilterTable

table
.1.3.6.1.4.1.10876.101.1.81.9.1 · 1 row entry · 5 columns
Open in standard view 
A table to L4 Switching rules in the system.
issL4SwitchingFilterEntry entry .1.3.6.1.4.1.10876.101.1.81.9.1.1
Each entry in this table is a L4 Switching rule.
Index to the table is L4 filter number.
Indexes
issL4SwitchingFilterNo
Column Syntax OID
issL4SwitchingFilterNo
L4 Switching Filter rule number.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.81.9.1.1.1
issL4SwitchingProtocol
The type of protocol to be checked against the packet. The
default value is 255. If the value is 255, it means that the
protocol type can be anything and it will not be checked to
decide the action.
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.10876.101.1.81.9.1.1.2
issL4SwitchingPortNo
The Layer 4 port no. Please note
these ports are the TCP / UDP ports.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.81.9.1.1.3
issL4SwitchingCopyToPort
This object is Port to which the packet would be switched
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.10876.101.1.81.9.1.1.4
issL4SwitchingFilterStatus
This object indicates the status of this entry.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.81.9.1.1.5

issModuleTable

table
.1.3.6.1.4.1.10876.101.1.81.12.1 · 1 row entry · 2 columns
Open in standard view 
A table for triggering Graceful shutdown and Start
issModuleEntry entry .1.3.6.1.4.1.10876.101.1.81.12.1.1
Each entry in this table corresponding to one protocol
Indexes
issModuleId
Column Syntax OID
issModuleId
This object indicates the ID of the protocol.
Following IDs are supported.
1. OSPF
2. OSPFV3
3. BGP
4. ISIS
5. RSVPTE
6. LDP
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.10876.101.1.81.12.1.1.1
issModuleSystemControl
This object shuts and starts the process
Enumerationr/w
Enumerated Values:
0idle
1shutdown
2start
 .1.3.6.1.4.1.10876.101.1.81.12.1.1.2

issSwitchFanTable

table
.1.3.6.1.4.1.10876.101.1.81.13.1 · 1 row entry · 2 columns
Open in standard view 
Table containing the Fan information.
issSwitchFanEntry entry .1.3.6.1.4.1.10876.101.1.81.13.1.1
Indicates information related to fan status of
the switch.
Indexes
issSwitchFanIndex
Column Syntax OID
issSwitchFanIndex
Indicates the fan number in the switch
Integer32
Constraints:
range: 1-5
 .1.3.6.1.4.1.10876.101.1.81.13.1.1.1
issSwitchFanStatus
Indicates the fan status of the switch.
Enumeration
Enumerated Values:
1up
2down
 .1.3.6.1.4.1.10876.101.1.81.13.1.1.2

issUDFilterTable

table
.1.3.6.1.4.1.10876.101.1.81.18.1 · 1 row entry · 18 columns
Open in standard view 
A table to configure User-Defined filter rules in the system.
issUDFilterEntry entry .1.3.6.1.4.1.10876.101.1.81.18.1.1
Each entry in this table is a User-Defined filter rule.
Index to the table is User-Defined filter number.
Indexes
issUDFilterNo
Column Syntax OID
issUDFilterNo
User-Defined Filter rule number.
This object is deprecated and the corresponding functionality is
met with issUDFilter objects in fsissext.mib.
Integer32
Constraints:
range: 1-50
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.1
issUDFilterPriority
The priority of the UDF filter can be used to decide which filter rule
is applicable when the packet matches with more than one filter rules.

Higher value of 'filter priority' implies a higher priority.
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.2
issUDFilterPktType
The packet header type to be filtered by User-Defined Filter.
Enumerationr/w
Enumerated Values:
0mac
1tcp
2udp
5ipv4
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.3
issUDFilterDstMacAddr
Destination MAC address to be matched with the packet. By Default, the
Destination Mac Address will be zero which means dont care condition ie)
any Dst Mac Address.
This object is valid only if the 'issUDFilterPktType' …
SNMPv2-TCMacAddressr/w
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.4
issUDFilterSrcMacAddr
Source MAC address to be matched with the packet. By Default, the Source
Mac Address will be zero which means dont care condition ie) any Src Mac
address.
This object is valid only if the 'issUDFilterPktType' is 'MAC'.
SNMPv2-TCMacAddressr/w
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.5
issUDFilterProtocol
The type of protocol to be checked against the packet. The
default value is 255. If the value is 255, it means that the
protocol type can be anything and it will not be checked to
decide the action.
This object is vali…
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.6
issUDFilterDstIpAddr
Destination IP address to be matched with the packet.
This object is valid only if the 'issUDFilterPktType' is 'IP', 'UDP' or 'TCP'.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.7
issUDFilterSrcIpAddr
Source IP address to be matched with the packet.
This object is valid only if the 'issUDFilterPktType' is 'IP', 'UDP' or 'TCP'.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.8
issUDFilterDstIpAddrMask
The IP subnet mask for Destination IP address.
This object is valid only if the 'issUDFilterPktType' is 'IP', 'UDP' or 'TCP'.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.9
issUDFilterSrcIpAddrMask
The IP subnet mask for Source IP address.
This object is valid only if the 'issUDFilterPktType' is 'IP', 'UDP' or 'TCP'.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.10
issUDFilterMinDstProtPort
The minimum port in the destination port range. Please note
these ports are the TCP / UDP ports.
This object is valid only if the 'issUDFilterPktType' is 'UDP' or 'TCP'.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.11
issUDFilterMaxDstProtPort
The maximum port in the destination port range. Please note
these ports are the TCP / UDP ports.
This object is valid only if the 'issUDFilterPktType' is 'UDP' or 'TCP'.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.12
issUDFilterMinSrcProtPort
The minimum port in the source port range. Please note
these ports are the TCP / UDP ports.
This object is valid only if the 'issUDFilterPktType' is 'UDP' or 'TCP'.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.13
issUDFilterMaxSrcProtPort
The maximum port in the source port range. Please note
these ports are the TCP / UDP ports.
This object is valid only if the 'issUDFilterPktType' is 'UDP' or 'TCP'.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.14
issUDFilterInPortList
Specifies the complete set of ports over which if the packet arrives
this filter rule will be applicable.
If the incoming port list is '0', the filter rule is applicable for all the
incoming ports.
By default inport li…
PortListr/w
Textual Convention: PortList OctetString
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.15
issUDFilterOutPortList
Specifies the complete set of ports over which if the packet goes out,
this filter rule will be applicable.
If the outgoing port list is '0',the filter rule is applicable for all the
outgoing packets in all ports.
The…
PortListr/w
Textual Convention: PortList OctetString
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.16
issUDFilterAction
Specifies the action to be taken on the packet if the filter
rule matches.
If the action is 'allow', the packet will be sent to the
ports in 'out port list'. If the out port list is '0',
the port over which the packet …
Enumerationr/w
Enumerated Values:
1allow
2drop
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.17
issUDFilterStatus
This object indicates the status of this entry. An entry is
created in this table when this object is SET to 'createAndWait'.
The entry in this table is used when the status of this object
is SET 'active'. The entry in…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.81.18.1.1.18

ecnProfileTable

table
.1.3.6.1.4.1.10876.101.1.81.19.1 · 1 row entry · 6 columns
Open in standard view 
A profile table to configure Explicit Congestion Notification (ECN) in the system.
ecnProfileEntry entry .1.3.6.1.4.1.10876.101.1.81.19.1.1
Each entry in this table is a Explicit Congestion Notification (ECN) profile .
Index to the table is profile name.
Indexes
ecnProfileName
Column Syntax OID
ecnProfileName
ECN Profile Name
OctetString
Constraints:
range: 1-32
 .1.3.6.1.4.1.10876.101.1.81.19.1.1.1
ecnProfileMinThreshold
Packets are treated normally when average queue size below minimum threshold (bytes).
Unsigned32r/w
Constraints:
range: 1-13631072
 .1.3.6.1.4.1.10876.101.1.81.19.1.1.2
ecnProfileMaxThreshold
Packets are marked congestion experienced when average queue size above maximum threshold (bytes).
Unsigned32r/w
Constraints:
range: 1-13631280
 .1.3.6.1.4.1.10876.101.1.81.19.1.1.3
ecnProfileProbability
The proportion of ECN marking varies linear with average queue size
when average queue size between minimum and maximum thresholds.
Unsigned32r/w
Constraints:
range: 0-100
 .1.3.6.1.4.1.10876.101.1.81.19.1.1.4
ecnProfilePortList
Specifies the inteface lists to be applied ECN profile.
e.g. 8040... : Port 1 and 6 ...
PortListr/w
Textual Convention: PortList OctetString
 .1.3.6.1.4.1.10876.101.1.81.19.1.1.5
ecnProfileRowStatus
This object is used to create and delete rows in the ecnProfileTable.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.10876.101.1.81.19.1.1.6