Module cold start - A module has completed power on testing after
initial power up, where gpoeTrapCode = 0.

Secondary link up - Secondary or backup redundant link port is active,
where gpoeTrapCode indicates the port number.

Secondary link down - Secondary or backup redundant link port is down,
where gpoeTrapCode indicates the port number.

Standby link up - Standby redundant link port is up and can become an
active link if the primary link goes down, where gpoeTrapCode
indicates the port number.

Standby link down - Standby redundant link port is down and cannot
become an active link if the primary link goes down, where
gpoeTrapCode indicates the port number.

Loop prevention block - Loop prevention block on a port has occurred
(RSTP block), where gpoeTrapCode indicates the port number.

Loop prevention clear - Loop prevention block on a port has been
removed (RSTP forward), where gpoeTrapCode indicates the port number.

Hardware DIP switch changed - Hardware DIP switch on the module has
changed state, where gpoeTrapCode indicates the switch number.

Software DIP switch changed - Software DIP switch on the module has
changed state, where gpoeTrapCode indicates the switch number.

Output relay - Output relay changed state, either from activated
to not activated or not activated to activated, where
gpoeTrapCode indicates the relay state:
  1 = not activated,
  2 = activated

Input pin status - Input pin changed state, either open to closed
or closed to open, where gpoeTrapCode indicates the relay state:
  1 = open,
  2 = closed

Module reset - a module completed power on testing after receiving
a reset command via user intervention, where gpoeTrapCode = 0.

Module configuration change - A configuration change has been committed
to flash, where gpoeTrapCode = 0.

Module over temperature - The module has detected that the module
temperature has risen above the safe operating temperature, which is 5
degrees less than the maximum temperature supported and is not
generated again unless the module first detects an operating
temperature five degrees below the over temperature threshold, where
gpoeTrapCode = 0.

Module normal temperature - The module has detected a normal operating
temperature range after a temperature out of range (low or high), where
gpoeTrapCode = 0.

Module voltage out of range - The module has detected that the internal
operating voltage is greater than 5% or less than 5% of nominal
internal voltage and the event is not generated again unless the module
first detects a safe operating voltage for more than 1 sec, where
gpoeTrapCode = 0.

Module voltage range normal - The module has detected a normal voltage
range after a voltage out of range (low or high), where
gpoeTrapCode = 0.

PoE PD status error - A port on the module has detected a PoE PD
error, where gpoePoeStatus indicates the specific PoE PD error and
gpoeTrapCode indicates the port number.

PoE PD status normal - A port on the module has detected no PoE PD
errors on a port where previously there had been one or more errors,
where gpoeTrapCode indicates the port number.

ACL access denied - The module has detected that access to the
management has been denied using a configured or default ACL, where
gpoeSourceIpString indicates the source IP address of the access, and
gpoeTrapCode = 0.

Telnet authentication failure - The module has detected a Telnet
authentication login failure, where gpoeSourceIpString indicates the
source IP address of the access, gpoeUsername indicates the username,
and gpoeTrapCode = 0.

Telnet session started - The module has detected that a Telnet session
has started, where gpoeSourceIpString indicates the source IP address
of the access, gpoeUsername indicates the username,
and gpoeTrapCode = 0.

Telnet session stopped - The module has detected that a Telnet session
has stopped, where gpoeSourceIpString indicates the source IP address
of the access, gpoeUsername indicates the username,
and gpoeTrapCode = 0.

FTP authentication failure - The module has detected an FTP
authentication login failure, where gpoeSourceIpString indicates the
source IP address of the access, gpoeUsername indicates the username,
and gpoeTrapCode = 0.

FTP session started - The module has detected that a FTP session
has started, where gpoeSourceIpString indicates the source IP address
of the access, gpoeUsername indicates the username,
and gpoeTrapCode = 0.

FTP session stopped - The module has detected that a FTP session
has stopped, where gpoeSourceIpString indicates the source IP address
of the access, gpoeUsername indicates the username,
and gpoeTrapCode = 0.

Serial console port session started - The module has detected that a
serial console session has started, where gpoeUsername indicates the
username and gpoeTrapCode = 0.

Serial console port session stopped - The module has detected that a
serial console session has stopped, where gpoeUsername indicates the
username and gpoeTrapCode = 0.

SSH authentication failure - Wrong SSH authentication type or password
is used, where gpoeSourceIpString indicates the source IP address,
gpoeUsername indicates the username, and gpoeTrapCode = 0.

SSH session started - SSH session for a user has started, where
gpoeSourceIpString indicates the source IP address, gpoeUsername
indicates the username, and gpoeTrapCode = 0.

SSH session stopped - SSH session for a user has stopped, where
gpoeSourceIpString indicates the source IP address, gpoeUsername
indicates the username, and gpoeTrapCode = 0.

Wrong password count exceeded - The module has detected too many wrong
password attempts (5) and will not validate any password attempts until
the device times out (5 minutes) or a session is aborted/closed by the
user. This is applicable for Serial port (Console), Telnet, FTP, and
SSH passwords, where gpoeSourceIpString indicates the source IP address,
gpoeUsername indicates the username, and gpoeTrapCode = 0.

Module power removed - The module has detected that incoming voltage
has been removed from a power input or has dropped to zero and is not
generated again unless the module first detects a safe operating
voltage for more than 1 sec, where gpoeTrapCode indicates
the power input.

SFP inserted - SFP has been inserted into a port, where
gpoeTrapCode indicates the port number.

SFP removed - SFP has been removed from a port, where gpoeTrapCode
indicates the port number.

SFP transmit low threshold - SFP has detected that the transmission
power on a port is less than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.

SFP transmit high threshold - SFP has detected that the transmission
power on a port is greater than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.

SFP current bias low threshold - SFP has detected that the current
bias on a port is less than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.

SFP current bias high threshold - SFP has detected that the current
bias on a port is greater than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.

SFP 3.3V low threshold - SFP has detected that the 3.3V source
voltage on a port is less than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.

SFP 3.3V high threshold - SFP has detected that the 3.3V source
voltage on a port is higher than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.

SFP low temperature threshold - SFP has detected that the low
temperature on a port is less than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.

SFP high temperature threshold - SFP has detected that the high
temperature on a port is less than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.

Module power applied - The module has detected that incoming voltage
has been applied to a power input and is not generated again unless
the module first detects that the power has been removed for more
than 1 sec, where gpoeTrapCode indicates the power input.

SFP receive low threshold - SFP has detected that the receive
power on a port is less than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.

SFP receive high threshold - SFP has detected that the receive
power on a port is greater than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.

SFP normal - SFP has detected normal operating conditions for the
port, where gpoeTrapCode indicates the port number.

Module configuration file corrupted - The management module has
detected a corrupted configuration file, where gpoeTrapCode = 0.

Link down - A port on the module has lost link, where gpoeTrapCode
indicates the port number.

Link up - A port on the module has gained link, where gpoeTrapCode
indicates the port number.

Primary link up - Primary redundant link port is active, where
gpoeTrapCode indicates the port number.

Primary link down - Primary redundant link port is down, where
gpoeTrapCode indicates the port number.