MX-VOICEIF-MIB Table View
Table-centric layout grouping table, row, and column objects.
Tables
4
Rows
4
Columns
55
voiceIfTable
table.1.3.6.1.4.1.4935.15.30.1.10
·
1 row entry
·
17 columns
A table of configuration for each voice over IP interface.
A row in the voiceIfTable used to configure each port.
Indexes
RFC1213-MIBifIndex
| Column | Syntax | OID | ||||||
|---|---|---|---|---|---|---|---|---|
|
voiceIfAdaptativeJitterBufferEnable
Jitter is an abrupt and unwanted variation of one or more signal
characteristics, such as the interval between successive pulses, or the frequency or phase of successive cycles. An adaptive jitter buffer usually consist… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.10.1.5 |
||||||
|
voiceIfTargetJitterBufferLength
The adaptive jitter buffer attempts to hold packets to the target
holding time. This is the minimum delay the jitter buffer adds to the system. The target jitter buffer length is in ms. The target jitter buffer MUST be … |
Unsigned32r/w Constraints: range: 0-300 |
.1.3.6.1.4.1.4935.15.30.1.10.1.6 |
||||||
|
voiceIfMaxJitterBufferLength
This is the maximum jitter the adaptive jitter buffer can handle.
The jitter buffer length is in ms. The maximum jitter buffer MUST be equal to or greater than the target jitter buffer. The maximum jitter buffer length … |
Unsigned32r/w Constraints: range: 0-300 |
.1.3.6.1.4.1.4935.15.30.1.10.1.7 |
||||||
|
voiceIfG711VoiceActivityDetectionEnable
If Voice Activity Detection (VAD) is enabled, then
speech frames are only sent during talkspurts (periods of audio activity). During silence periods, no speech frames are sent, but Comfort Noise (CN) pack… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.10.1.10 |
||||||
|
voiceIfEchoCancellationEnable
An echo is a signal that has been reflected or otherwise returned
with sufficient magnitude and delay to be perceived. The echo cancellation is usually an active process in which echo signals are measured and cancelled … |
MX-TCMxEnableStater/w Textual Convention: MX-TCMxEnableState EnumerationType Values:
|
.1.3.6.1.4.1.4935.15.30.1.10.1.11 |
||||||
|
voiceIfG711ComfortNoiseGenerationEnable
During silence periods, Comfort Noise (CN) packets
containing information about background noise may be received (c.f. RFC3389). If Comfort Noise Generation (CNG) is enabled, then those packets are used t… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.10.1.12 |
||||||
|
voiceIfBaseGainConfigurationSource
deprecated
Specify how the base gain is configured.
When using the custom configuration, you must set the following variables: voiceIfBaseInputGain, voiceIfBaseOutputGain, voiceIfBaseInputGainOffset, voiceIfBaseOutputG… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.10.1.17 |
||||||
|
voiceIfUserInputGainOffset
The user input gain offset is added to the base input gain to
compute the total input gain. The user input gain is in dB. Valid input gain range is between -30 dB and 20 dB. |
MX-TCMxFloatingPointr/w Textual Convention: MX-TCMxFloatingPoint OctetStringType Constraints: range: 1..255 |
.1.3.6.1.4.1.4935.15.30.1.10.1.20 |
||||||
|
voiceIfUserOutputGainOffset
The user output gain offset is added to the base output gain to
compute the total output gain. The user ouput gain is in dB. Valid output gain range is between -30 dB and 20 dB. |
MX-TCMxFloatingPointr/w Textual Convention: MX-TCMxFloatingPoint OctetStringType Constraints: range: 1..255 |
.1.3.6.1.4.1.4935.15.30.1.10.1.21 |
||||||
|
voiceIfBaseInputGain
deprecated
The base input gain. This is an absolute value which is used
in conjunction with the user input gain and the base input gain offset to compute the total input gain. This object is deprecated. This means s… |
Unsigned32r/w Constraints: range: 0-65535 |
.1.3.6.1.4.1.4935.15.30.1.10.1.22 |
||||||
|
voiceIfBaseOutputGain
deprecated
The base output gain. This is an absolute value which is used
in conjunction with the user output gain and the base output gain offset to compute the total output gain. This object is deprecated. This mea… |
Unsigned32r/w Constraints: range: 0-65535 |
.1.3.6.1.4.1.4935.15.30.1.10.1.23 |
||||||
|
voiceIfBaseInputGainOffset
deprecated
The base input gain offset. This value is used in the calibration
to adjust the total input gain to an offset in dB from the base input gain. This value is in dB. This object is deprecated. This means som… |
MX-TCMxFloatingPointr/w Textual Convention: MX-TCMxFloatingPoint OctetStringType Constraints: range: 1..255 |
.1.3.6.1.4.1.4935.15.30.1.10.1.24 |
||||||
|
voiceIfBaseOutputGainOffset
deprecated
The base output gain offset. This value is used in the calibration
to adjust the total output gain to an offset in dB from the base output gain. This value is in dB. This object is deprecated. This means … |
MX-TCMxFloatingPointr/w Textual Convention: MX-TCMxFloatingPoint OctetStringType Constraints: range: 1..255 |
.1.3.6.1.4.1.4935.15.30.1.10.1.25 |
||||||
|
voiceIfNlpThresholdLevel
deprecated
The echo cancellation NLP threshold level.
0 : Strongest echo cancellation, weakest double-talk detection. 4 : Weakest echo cancellation, strongest double-talk detection. Increase the value… |
Unsigned32r/w Constraints: range: 0-4 |
.1.3.6.1.4.1.4935.15.30.1.10.1.35 |
||||||
|
voiceIfG729VoiceActivityDetectionEnable
If Voice Activity Detection (VAD) is enabled, then
speech frames are only sent during talkspurts (periods of audio activity). During silence periods, no speech frames are sent, but Comfort Noise (CN) pack… |
MX-TCMxEnableStater/w Textual Convention: MX-TCMxEnableState EnumerationType Values:
|
.1.3.6.1.4.1.4935.15.30.1.10.1.50 |
||||||
|
voiceIfG723VoiceActivityDetectionEnable
If Voice Activity Detection (VAD) is enabled, then
speech frames are only sent during talkspurts (periods of audio activity). During silence periods, no speech frames are sent, but Comfort Noise (CN) pack… |
MX-TCMxEnableStater/w Textual Convention: MX-TCMxEnableState EnumerationType Values:
|
.1.3.6.1.4.1.4935.15.30.1.10.1.80 |
||||||
|
voiceIfSignalLimiterLevel
When enabled, the Signal Limiter attenuates or
removes peaks in voice signal. This may reduce the presence of echo but may impair DTMF detection because of signal distortion. 0: Disable Sig… |
Integer32r/w Constraints: range: 0-5 |
.1.3.6.1.4.1.4935.15.30.1.10.1.90 |
voiceIfCodecTable
table.1.3.6.1.4.1.4935.15.30.1.20
·
1 row entry
·
29 columns
This table holds the parameters that define the
codecs used.
PCMA and PCMU are specified in ITU-T Recommendation G.711. Audio
data is encoded as eight bits per sample, after logarithmic
scaling. PCMU denotes mu-law scaling, PCMA A-law scaling.
G723.1 is specified in ITU Recommendation G.723.1, Dual-rate speech
coder for multimedia communications transmitting at 5.3 and 6.3
kbit/s. This Recommendation specifies a coded representation that can
be used for compressing the speech signal component of multi-media
services at a very low bit rate. Audio is encoded in 30 ms frames.
A G.723.1 frame can be one of three sizes: 24 octets (6.3 kb/s frame),
20 octets (5.3 kb/s frame), or 4 octets. These 4-octet frames are
called SID frames (Silence Insertion Descriptor) and are used to
specify comfort noise parameters.
G.726 is specified in ITU-T Recommendation G.726: 40, 32, 24,
16 kbit/s adaptive differential pulse code modulation (ADPCM).
It describes the algorithm recommended for conversion of a single
64 kbit/s A-law or U-law PCM channel encoded at 8000 samples/sec to
and from a 40, 32, 24, or 16 kbit/s channel. The conversion is
applied to the PCM stream using an Adaptive Differential Pulse Code
Modulation (ADPCM) transcoding technique.
G729 is specified in ITU-T Recommendation G.729, Coding of speech at
8 kbit/s using conjugate structure-algebraic code excited linear
prediction (CS-ACELP). For all data rates, the sampling frequency
(and RTP timestamp clock rate) is 8000 Hz. A voice activity detector
(VAD) and comfort noise generator (CNG) algorithm in Annex B of G.729
is RECOMMENDED for digital simultaneous voice and data applications
and can be used in conjunction with G.729 or G.729 Annex A. A G.729
or G.729 Annex A frame contains 10 octets, while the G.729 Annex B
comfort noise frame occupies 2 octets.
Codec table parameter entries.
Indexes
RFC1213-MIBifIndex
| Column | Syntax | OID | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
voiceIfCodecPreferred
Indicates the preferred type of codec for voice
transmission. If the selected codec is disabled, this preferred type of codec will be ignored. This variable's semantics are different depending on protocol… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.20.1.1 |
||||||||||||||||
|
voiceIfCodecPcmuEnable
Indicates if the codec can be selected for voice
transmission. If enabled, this codec will be listed as supported for this specific endpoint. Otherwise, it will be ignored. |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.20.1.5 |
||||||||||||||||
|
voiceIfCodecPcmuMinPTime
Shortest packetization period allowed for the PCMU codec.
Expressed in milliseconds. Authorized values start at 10 and come in discrete steps of 10 ms up to the one specified by variable voiceIfCodecPcmu… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.6 |
||||||||||||||||
|
voiceIfCodecPcmuMaxPTime
Longest packetization period allowed for the PCMU codec.
Expressed in milliseconds. Authorized values go up to 100, in discrete steps of 10 ms, and start at the one specified by variable voiceIfCodecPcmu… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.7 |
||||||||||||||||
|
voiceIfCodecPcmaEnable
Indicates if the codec can be selected for voice
transmission. If enabled, this codec will be listed as supported for this specific endpoint. Otherwise, it will be ignored. |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.20.1.11 |
||||||||||||||||
|
voiceIfCodecPcmaMinPTime
Shortest packetization period allowed for the PCMA codec.
Expressed in milliseconds. Authorized values start at 10 and come in discrete steps of 10 ms up to the one specified by variable voiceIfCodecPcma… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.12 |
||||||||||||||||
|
voiceIfCodecPcmaMaxPTime
Longest packetization period allowed for the PCMA codec.
Expressed in milliseconds. Authorized values go up to 100, in discrete steps of 10 ms, and start at the one specified by variable voiceIfCodecPcma… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.13 |
||||||||||||||||
|
voiceIfCodecG723Enable
Indicates if the codec can be selected for voice
transmission. If not disabled, this codec is listed as supported for this specific endpoint. Otherwise, it is ignored. - disable: Disable G.723 - g723-53kb… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.20.1.17 |
||||||||||||||||
|
voiceIfCodecG723MinPTime
Shortest packetization period allowed for the G.723 codec.
Expressed in milliseconds. Authorized values start at 30 and come in discrete steps of 30 ms up to the one specified by variable voiceIfCodecG72… |
Unsigned32r/w Constraints: range: 30-30range: 60-60range: 90-90range: 120-120 |
.1.3.6.1.4.1.4935.15.30.1.20.1.18 |
||||||||||||||||
|
voiceIfCodecG723MaxPTime
Longest packetization period allowed for the G.723 codec.
Expressed in milliseconds. Authorized values go up to 120, in discrete steps of 30 ms, and start at the one specified by variable voiceIfCodecG72… |
Unsigned32r/w Constraints: range: 30-30range: 60-60range: 90-90range: 120-120 |
.1.3.6.1.4.1.4935.15.30.1.20.1.19 |
||||||||||||||||
|
voiceIfCodecG729Enable
Indicates if the codec can be selected for voice
transmission. If enabled, this codec will be listed as supported for this specific endpoint. Otherwise, it will be ignored. |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.20.1.23 |
||||||||||||||||
|
voiceIfCodecG729MinPTime
Shortest packetization period allowed for the G.729 codec.
Expressed in milliseconds. Authorized values start at 10 and come in discrete steps of 10 ms up to the one specified by variable voiceIfCodecG72… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.24 |
||||||||||||||||
|
voiceIfCodecG729MaxPTime
Longest packetization period allowed for the G.729 codec.
Expressed in milliseconds. Authorized values go up to 100, in discrete steps of 10 ms, and start at the one specified by variable voiceIfCodecG72… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.25 |
||||||||||||||||
|
voiceIfCodecG72616kbpsEnable
Indicates if the codec can be selected for voice
transmission. If enabled, this codec is listed as supported for this specific endpoint. Otherwise, it is ignored. Note that if G.726 at 16 kbps is enabled,… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.20.1.50 |
||||||||||||||||
|
voiceIfCodecG72616kbpsPayloadType
When enabling G.726 at 16 kbps for voice transmission, this
variable determines the actual RTP dynamic payload type used in an initial offer. The payload types available are as per RFC 3551. … |
Unsigned32r/w Constraints: range: 96-127 |
.1.3.6.1.4.1.4935.15.30.1.20.1.55 |
||||||||||||||||
|
voiceIfCodecG72616kbpsMinPTime
Shortest packetization period allowed for the G.726-16kbps codec.
Expressed in milliseconds. Authorized values start at 10 and come in discrete steps of 10 ms up to the one specified by variable voiceIfC… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.60 |
||||||||||||||||
|
voiceIfCodecG72616kbpsMaxPTime
Longest packetization period allowed for the G.726-16kbps codec.
Expressed in milliseconds. Authorized values go up to 100, in discrete steps of 10 ms, and start at the one specified by variable voiceIfC… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.65 |
||||||||||||||||
|
voiceIfCodecG72624kbpsEnable
Indicates if the codec can be selected for voice
transmission. If enabled, this codec is listed as supported for this specific endpoint. Otherwise, it is ignored. Note that if G.726 at 24 kbps is enabled,… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.20.1.70 |
||||||||||||||||
|
voiceIfCodecG72624kbpsPayloadType
When enabling G.726 at 24 kbps for voice transmission, this
variable determines the actual RTP dynamic payload type used in an initial offer. The payload types available are as per RFC 3551. … |
Unsigned32r/w Constraints: range: 96-127 |
.1.3.6.1.4.1.4935.15.30.1.20.1.75 |
||||||||||||||||
|
voiceIfCodecG72624kbpsMinPTime
Shortest packetization period allowed for the G.726-24kbps codec.
Expressed in milliseconds. Authorized values start at 10 and come in discrete steps of 10 ms up to the one specified by variable voiceIfC… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.80 |
||||||||||||||||
|
voiceIfCodecG72624kbpsMaxPTime
Longest packetization period allowed for the G.726-24kbps codec.
Expressed in milliseconds. Authorized values go up to 100, in discrete steps of 10 ms, and start at the one specified by variable voiceIfC… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.85 |
||||||||||||||||
|
voiceIfCodecG72632kbpsEnable
Indicates if the codec can be selected for voice
transmission. If enabled, this codec is listed as supported for this specific endpoint. Otherwise, it is ignored. Note that if G.726 at 32 kbps is enabled,… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.20.1.90 |
||||||||||||||||
|
voiceIfCodecG72632kbpsPayloadType
When enabling G.726 at 32 kbps for voice transmission, this
variable determines the actual RTP dynamic payload type used in an initial offer. The payload types available are as per RFC 3551. … |
Unsigned32r/w Constraints: range: 96-127 |
.1.3.6.1.4.1.4935.15.30.1.20.1.100 |
||||||||||||||||
|
voiceIfCodecG72632kbpsMinPTime
Shortest packetization period allowed for the G.726-32kbps codec.
Expressed in milliseconds. Authorized values start at 10 and come in discrete steps of 10 ms up to the one specified by variable voiceIfC… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.105 |
||||||||||||||||
|
voiceIfCodecG72632kbpsMaxPTime
Longest packetization period allowed for the G.726-32kbps codec.
Expressed in milliseconds. Authorized values go up to 100, in discrete steps of 10 ms, and start at the one specified by variable voiceIfC… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.110 |
||||||||||||||||
|
voiceIfCodecG72640kbpsEnable
Indicates if the codec can be selected for voice
transmission. If enabled, this codec is listed as supported for this specific endpoint. Otherwise, it is ignored. Note that if G.726 at 40 kbps is enabled,… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.20.1.115 |
||||||||||||||||
|
voiceIfCodecG72640kbpsPayloadType
When enabling G.726 at 40 kbps for voice transmission, this
variable determines the actual RTP dynamic payload type used in an initial offer. The payload types available are as per RFC 3551. … |
Unsigned32r/w Constraints: range: 96-127 |
.1.3.6.1.4.1.4935.15.30.1.20.1.120 |
||||||||||||||||
|
voiceIfCodecG72640kbpsMinPTime
Shortest packetization period allowed for the G.726-40kbps codec.
Expressed in milliseconds. Authorized values start at 10 and come in discrete steps of 10 ms up to the one specified by variable voiceIfC… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.125 |
||||||||||||||||
|
voiceIfCodecG72640kbpsMaxPTime
Longest packetization period allowed for the G.726-40kbps codec.
Expressed in milliseconds. Authorized values go up to 100, in discrete steps of 10 ms, and start at the one specified by variable voiceIfC… |
Unsigned32r/w Constraints: range: 10-10range: 20-20range: 30-30range: 40-40range: 50-50range: 60-60range: 70-70range: 80-80range: 90-90range: 100-100 |
.1.3.6.1.4.1.4935.15.30.1.20.1.130 |
.1.3.6.1.4.1.4935.15.30.1.30
·
1 row entry
·
3 columns
This table holds the parameters that define the DTMF transport.
DTMF transport table parameter entries.
Indexes
RFC1213-MIBifIndex
| Column | Syntax | OID | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
|
voiceIfDtmfTransport
Type of DTMF transport. If signalingProtocolDependent is selected, the
signaling protocol has the control to select the DTMF transport mode. This variable's semantics are different depending on protocol a… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4935.15.30.1.30.1.1 |
||||||||
|
voiceIfDtmfPayloadType
When selecting outOfBandUsingRtp(1) as DTMF transport mode
(see variable voiceIfDtmfTransport), this variable determines the actual RTP dynamic payload type used for telephone-event in an initial offer. The payload type… |
Unsigned32r/w Constraints: range: 96-127 |
.1.3.6.1.4.1.4935.15.30.1.30.1.5 |
||||||||
|
voiceIfDtmfEnforceDefaultEvents
This variable is used when a deliberate deviance to RFC 2833
is required. When enabled, conformance is enforced and support for RFC 2833 will imply the support of basic telephony-events. When setting the… |
MX-TCMxEnableStater/w Textual Convention: MX-TCMxEnableState EnumerationType Values:
|
.1.3.6.1.4.1.4935.15.30.1.30.1.55 |
.1.3.6.1.4.1.4935.15.30.1.40
·
1 row entry
·
6 columns
This table holds DTMF detection parameters indexed by endpoint number.
DTMF detection entry.
Indexes
RFC1213-MIBifIndex
| Column | Syntax | OID |
|---|---|---|
|
voiceIfDtmfDetectionMaxPowerThreshold
Maximum absolute power threshold (dBm0) for off-on
transition of a DTMF. Raising this value increases the sensitivity of the DTMF detection. Raising this value too high may also cause false detections of … |
Integer32r/w Constraints: range: -20-1 |
.1.3.6.1.4.1.4935.15.30.1.40.1.20 |
|
voiceIfDtmfDetectionMinPowerThreshold
Minimum absolute power threshold (dBm0) for off-on
transition of a DTMF. Raising this value reduces the sensitivity to DTMF detection. This variable's semantics are different depending on p… |
Integer32r/w Constraints: range: -45--10 |
.1.3.6.1.4.1.4935.15.30.1.40.1.30 |
|
voiceIfDtmfDetectionBreakPowerThreshold
Break absolute power threshold (dBm0) for on-off transition
of a DTMF. This variable's semantics are different depending on protocol and/or hardware platforms. Please refer to the documentation for more d… |
Integer32r/w Constraints: range: -45--12 |
.1.3.6.1.4.1.4935.15.30.1.40.1.40 |
|
voiceIfDtmfDetectionPositiveTwist
When the high-group frequency of a DTMF is more powerful
than the low-group frequency, the difference between the high-group frequency absolute power and the low-group frequency absolute power must be smaller than or eq… |
Unsigned32r/w Constraints: range: 1-10 |
.1.3.6.1.4.1.4935.15.30.1.40.1.50 |
|
voiceIfDtmfDetectionNegativeTwist
When the low-group frequency of a DTMF is more powerful
than the high-group frequency, the difference between the low-group frequency absolute power and the high-group frequency absolute power must be smaller than or eq… |
Unsigned32r/w Constraints: range: 1-10 |
.1.3.6.1.4.1.4935.15.30.1.40.1.60 |
|
voiceIfDtmfDetectionMinDuration
Defines the minimum duration a DTMF must last to be detected. A DTMF
whose duration is less than the configured value is not detected. A higher value may help prevent false DTMF detection. However, increasing the minimu… |
Unsigned32r/w Constraints: range: 30-5000 |
.1.3.6.1.4.1.4935.15.30.1.40.1.70 |