A trap which signifies that Loss Of Signal has been detected.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name.

A trap which signifies Loss of timing information is cleared.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name.

A trap which signifies ACBC FPGA version is not compatible.
          
jnxBootCpldFpgaRevMajor indicates the current ACBC FPGA Major revision
jnxBootCpldFpgaRevMinor indicates the current ACBC FPGA Minor revision.

A trap which signifies Boot-cpld version is not compatible.
          
jnxClksyncVersion indicates the current Boot-cpld version.

A trap which signifies Primary source failed
(Whenever PFM/CFM/SCM error occurs).
          
jnxClksyncIfIndex is the Primary source interface index
jnxClksyncIntfName is the Primary source interface name.

A trap which signifies Secondary source failed
(Whenever PFM/CFM/SCM error occurs).
          
jnxClksyncIfIndex is the Secondary source interface index
jnxClksyncIntfName is the Secondary source interface name.

A trap which signifies: 
When acting as MASTER - Failing/rejecting clients for signaling messages
When acting as SLAVE - Failing or receiving rejection for signaling messages
          
jnxClkStreamHandle is the clock stream handle
jnxRemoteIpAddr is the clock stream's remote ip-address.

A trap which signifies: 
When acting as MASTER - Failing/rejecting clients for signaling messages
When acting as SLAVE - Failing or receiving rejection for signaling messages
          
jnxClkStreamHandle is the clock stream handle
jnxRemoteIpAddr is the clock stream's remote ip-address.

A trap which signifies that interface status changed to squelched.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name.

A trap which signifies that interface status changed to active.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name.

A trap which signifies that Loss Of Signal has been cleared.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name.

A trap which signifies that there is no foreign master available.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies Exceeded frequency deviation.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name.

A trap which signifies that there is now a foreign master available.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies that the local clock is out of sync.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies that the local clock is no more out of sync.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies that EEC has lost reference1.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies that EEC has regained reference1.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies that EEC has lost reference2.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies that EEC has regained reference2.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies Exceeded frequency deviation cleared.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name.

A trap which signifies that EEC has no references to lock.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies that EEC has a reference to lock.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies that EEC QL has fallen below threshold.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies that EEC QL has regained the threshold.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies that TOD input signal has failed.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies Loss of ESMC is set.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name.

A trap which signifies that TOD input signal is good.
          
jnxClksyncAdditionalInformationStr has additional information for the trap.
          
This TRAP is supported only on ACX710.

A trap which signifies Loss of ESMC is cleared.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name.

A trap which signifies ESMC/SSM Quality Level failed is set.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name.

A trap which signifies ESMC/SSM Quality Level failed is cleared.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name.

A trap which signifies Loss of timing information is set.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name.

A trap which signifies Primary source recovered.
          
jnxClksyncIfIndex is the Primary source interface index
jnxClksyncIntfName is the Primary source interface name.

A trap which signifies that Synce DPLL state change
(unknown, lock_acq, locked, holdover, freerun).
          
jnxClksyncIfIndex is the interface index from which Frequency is derived
jnxClksyncIntfName is the interface name from which Frequency is derived
jnxClksyncDpllState indicates the Dpll status
jnxClksyncDpllStateStr indicates the Dpll status in string format.

A trap which signifies that BITS DPLL state change
(unknown, lock_acq, locked, holdover, freerun).
          
jnxClksyncIfIndex is the interface index from which Frequency is derived
jnxClksyncIntfName is the interface name from which Frequency is derived
jnxClksyncDpllState indicates the Dpll status
jnxClksyncDpllStateStr indicates the Dpll status in string format.

A trap which signifies that PTP servo state
(Init, Acquiring, PhaseAligned, FreeRun, Holdover). 
          
jnxPtpServoState indicates the ptp servo status
jnxPtpServoStateStr indicates the ptp servo status in string format.

A trap which signifies PTP clock class changes.
          
jnxPtpGmId indicates the ptp Grand Master clock-id
jnxPtpClass indicates the ptp Grand Master clock status.

A trap which signifies PTP clock accuracy changes.
          
jnxPtpGmId indicates the ptp Grand Master clock-id
jnxPtpAccuracy indicates the ptp Grand Master clock accuracy.

A trap which signifies PTP Grand Master changes.
          
jnxPtpGmId indicates the ptp Grand Master clock-id.

A trap which signifies that Hybrid state
(Init, FreqAcq, FreqLckPhaseAcq, FreqPhaseLck). 
          
jnxClksyncHybridState indicates the hybrid status
jnxClksyncHybridStateStr indicates the hybrid status in string format.

A trap which signifies TX SSM/ESMC quality level changed.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name
jnxClksyncColorStr is the color of the LED unit.

A trap which signifies Secondary source recovered.
          
jnxClksyncIfIndex is the Secondary source interface index
jnxClksyncIntfName is the Secondary source interface name.

A trap which signifies Passive Port Threshold Exceeded.
          
jnxPtpPhaseOffsetThresholdExceeded indicates whether the Phase Threshold
of the monitored Passive Port has exceeded the configured Max Phase Offset
Threshold as per.

A trap which signifies Primary reference changed
(Ifd name change or change from synce to BITS/external interface etc).
          
jnxClksyncIfIndex is the Primary reference interface index
jnxClksyncIntfName is the Primary reference interface name.

A trap which signifies Secondary reference changed
(Ifd name change or change from synce to BITS/external interface etc).
          
jnxClksyncIfIndex is the Secondary reference interface index
jnxClksyncIntfName is the Secondary reference interface name.

A trap which signifies RX SSM/ESMC quality level changed.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name
jnxClksyncQualityCode is the SSM/ESMC quality level 
jnxClksyncQualityCodeStr is the SSM/ESMC quality level in string format.

A trap which signifies TX SSM/ESMC quality level changed.
          
jnxClksyncIfIndex is the interface index
jnxClksyncIntfName is the interface name
jnxClksyncQualityCode is the SSM/ESMC quality level 
jnxClksyncQualityCodeStr is the SSM/ESMC quality level in string format.

A trap which signifies SyncE Holdover to Locked EEC state.
          
jnxClksyncIfIndex is the SyncE interface index
jnxClksyncIntfName is the SyncE interface name.

A trap which signifies SyncE Locked to Holdover EEC state.
          
jnxClksyncIfIndex is the SyncE interface index
jnxClksyncIntfName is the SyncE interface name.

A trap which signifies that DPLL state change
(unknown, lock_acq, locked, holdover, freerun).
          
jnxClksyncDpllState indicates the Dpll status
jnxClksyncDpllStateStr indicates the Dpll status in string format.