ENTERASYS-CONVERGENCE-END-POINT-MIB Table View

This table represents all Convergence End Point types
supported by this entity, and provides a default policy
profile for each Convergence End Point type.

This table provides control of Convergence End Point detection
and discovery on a per interface and per Convergence End Point
type basis.
          
Maintaining the values of this table across system reboots
is REQUIRED.

This table provides a mapping from the entities interfaces
to discovered Convergence End Points.
          
Maintaining the value of this object across system reboots
is NOT REQUIRED.

This table provides information on each of the Convergence
End Points that has been discovered or detected by this
entity.
          
Maintaining the value of this object across system reboots
is NOT REQUIRED.

A table that describes the IP address and IP port based
Convergence End Point detection parameters.
          
Packets on interfaces that are configured to detect End
Points, via the etsysConvEndPointProtocolConfigTable,
that are defined in this table are inspected to determine
if a Convergence End Point exists on that interface.
          
Rules applying to Convergence End Point types that are
configured for detection are evaluated according to the
following:
          
1.  If etsysConvEndPointDetectionProtocol does not have
    any bits set, this indicates that the port based detection
    should not be performed, proceed to step 2.  Otherwise
    the value in etsysConvEndPointDetectionProtocol is
    evaluated against the protocol field in the IP header,
    if it is of a, or the, type specified then the destination
    port must be between the values of
    etsysConvEndPointDetectionPortLow and
    etsysConvEndPointDetectionPortHigh, inclusive.
          
2.  If the etsysConvEndPointDetectionAddr is null, this 
    indicates that no detection address check should be 
    performed, consider the End Point detected.  Otherwise
    the value the of etsysConvEndPointDetectionAddr will be
    masked with the value of etsysConvEndPointDetectionAddrMask,
    via a bitwise AND operation, and this value will be compared
    with the destination IP address that has also been masked
    with the value of etsysConvEndPointDetectionAddrMask,
    via a bitwise AND operation, if they are equal then
    consider the End Point detected.
          
If there are no rows in this table that are in the active
state then the following pseudo entries describe the
behavior of the IP based Convergence End Point detection.
          
   EndPointType siemens
   Protocol     { { udp, tcp } }
   PortLow      4060
   PortHigh     4060
   AddrType     unknown
   Addr         ''
   AddrMaskType unknown
   AddrMask     ''
          
   EndPointType h323
   Protocol     { { udp, tcp } }
   PortLow      1718
   PortHigh     1720
   AddrType     ipv4
   Addr         '224.0.1.41'
   AddrMaskType ipv4
   AddrMask     '255.255.255.255'
          
   EndPointType sip
   Protocol     { { udp, tcp } }
   PortLow      5060
   PortHigh     5060
   AddrType     ipv4
   Addr         '224.0.1.75'
   AddrMaskType ipv4
   AddrMask     '255.255.255.255'
          
   EndPointType h323
   Protocol     { { udp, tcp } }
   PortLow      1718
   PortHigh     1720
   AddrType     unknown
   Addr         ''
   AddrMaskType unknown
   AddrMask     ''
          
   EndPointType sip
   Protocol     { { udp, tcp } }
   PortLow      5060
   PortHigh     5060
   AddrType     unknown
   Addr         ''
   AddrMaskType unknown
   AddrMask     ''
          
If one or more entries in this table are active the active
entries will define the IP based detection behavior in its
entirety.
          
Maintaining entries in this table across system reboots is 
REQUIRED for entries with an etsysConvEndPointDetectionRowStatus
value of active(1).

A table of per port configuration for Convergence End Point
detection.
          
Maintaining the value of this object across system reboots
is NOT REQUIRED.

A table of per port configuration for Convergence End Point
detection related to the Cisco CDP protocol.  Only ports
that are capable of participating in Cisco CDP protocol are 
represented in this table.