CISCO-LWAPP-REAP-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
37
Rows
37
Columns
228

cLReapWlanConfigTable

table
.1.3.6.1.4.1.9.9.517.1.1.1 · 1 row entry · 8 columns
Open in standard view 
This table represents the WLAN configuration sent by
the controller to REAPs so that the APs can operate
in stand-alone mode.
          
LWAPP APs operating in REAP mode locally switch 
the data frames of the associated clients, rather 
than tunneling them through to the LWAPP controller 
as LWAPP data packets.  The LWAPP controller
passes this configuration set to the LWAPP AP during
the AP initialization so that the AP can operate
in stand-alone mode when it fails to reach the
controller.  The configuration is also passed to
the REAP when they are individually modified through
separate LWAPP messages.  The REAP updates itself
with the information received through these LWAPP
messages.
          
This table has a one-to-one relationship with
cLWlanConfigTable of the CISCO-LWAPP-WLAN-MIB.  There
exist a row in this table corresponding to each
row representing a WLAN in cLWlanConfigTable.
          
Note that the configuration represented by this 
table is applicable only for REAPs.  The 
controller will send this configuration set only to 
the REAP APs for their operation in standalone
mode.
cLReapWlanConfigEntry entry .1.3.6.1.4.1.9.9.517.1.1.1.1
Each entry represents a conceptual row in
cLReapWlanConfigTable and corresponds to the
packet switching configuration for a
particular WLAN.
Indexes
Column Syntax OID
cLReapWlanEnLocalSwitching
This object specifies the behavior of the REAP
when switching the data frames of the clients
associated to it through the WLAN identified
by cLWlanIndex.

A value of 'true' indicates that the AP, on which …
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.1.1.1.1
cLReapWlanClientIpLearnEnable
This object specifies whether Client IP Address
learning is enabled on the controller. When layer
two tunneling is employed the IP learning on
controller has to be disabled. Otherwise, the controller
is unable to learn…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.1.1.1.2
cLReapWlanApAuth
This object specifies the behavior of the REAP,
on where to handle the authentication of the client
associated to the WLAN indicated by cLWlanIndex.

A value of 'true' indicates that the AP, on which
this …
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.1.1.1.3
cLReapWlanVlanCentralSwitching
This object specifies whether the AP bridges the traffic
centrally. If the VLAN is not configured on the AP uplink,
the AP will tunnel the traffic back to the Wireless LAN
Controller (WLC) where it is registered. Then …
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.1.1.1.4
cLReapWlanDhcpCentral
This object specifies the behavior of the REAP
when switching the DHCP packets of the clients
associated to it through the WLAN identified
by cLWlanIndex.

A value of 'true' indicates that the AP, should t…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.1.1.1.5
cLReapWlanDhcpOverrideDNS
This object specifies the behavior of the REAP
when switching the DNS frames of the clients
associated to it through the WLAN identified
by cLWlanIndex.

A value of 'true' indicates that the AP, should tun…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.1.1.1.6
cLReapWlanNatPatEnabled
This object specifies whether Network Address
Translation (NAT) and Port Address Trnaslation (PAT)
are enabled on this WLAN. This can be enabled only
when cLReapWlanDhcpCentral is set to 'true'.

A value o…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.1.1.1.7
cLReapWlanAssocCentral
This object specifies the behavior of the REAP
when handling the (re-)association management frames from
the clients through the WLAN identified
by cLWlanIndex.

A value of 'true' indicates AP should tunne…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.1.1.1.8

cLReapApConfigTable

table
.1.3.6.1.4.1.9.9.517.1.2.1 · 1 row entry · 8 columns
Open in standard view 
This table represents the VLAN configuration of
REAPs.
          
The agent adds a row to this table corresponding to
each row representing a REAP in cLApTable of the
CISCO-LWAPP-AP-MIB.  The agent deletes the row
either when the AP dissociates from the
controller or moved out of the remote mode.
cLReapApConfigEntry entry .1.3.6.1.4.1.9.9.517.1.2.1.1
Each entry represents a conceptual row in
cLReapApConfigTable and corresponds to the
VLAN configuration of a REAP.
Indexes
CISCO-LWAPP-AP-MIBcLApSysMacAddress
Column Syntax OID
cLReapApNativeVlanId
This object specifies the Native VLAN ID for the
particular AP identified by cLApSysMacAddress.
This particular object can be modified
through a Set request only if the AP is a REAP.
The agent is expected to reject the…
Unsigned32r/w
Constraints:
range: 1-4095
 .1.3.6.1.4.1.9.9.517.1.2.1.1.1
cLReapApVlanEnable
This object specifies the availability of Native
VLAN configured through cLReapApNativeVlanId on
this REAP.

A value of 'true' indicates that the VLAN configured
as native through cLReapApNativeVlanId is e…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.2.1.1.2
cLReapHomeApEnable
This object specifies if this REAP AP is used
as Home AP.

A value of 'true' indicates that this REAP AP is
a Home AP.

A value of 'false' indicates that this REAP AP is
not a Home AP.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.2.1.1.3
cLReapApLeastLatencyJoinEnable
This object specifies if this REAP AP should join
controller which has least latency.

A value of 'true' indicates that this REAP AP will
join controller which has least latency.

A value of …
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.2.1.1.4
cLReapHomeApLocalSsidReset
This object specifies to reset local SSID on a
Home AP.
A value of 'true' indicates that the local SSID
is to be reset.
A value of 'false' on this during set will return
error.
A value of false will be returned on get.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.2.1.1.5
cLReapInstallMappingRadioBackhaul
This object specifies whether to enable or disable
WLANs on backhaul radio.

A value of 'true' indicates that wlan mapping would
be enabled on backhaul radio.

A value of 'false' indicates th…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.2.1.1.6
cLReapApResilientMode
This object specifies whether to enable or disable
standalone mode support on a REAP AP.

A value of 'true' indicates that standalone mode would
be enabled on backhaul radio.

A value of 'fal…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.2.1.1.7
cLReapApNativeVlanLevel
This object specifies to make a REAP AP to force
inherit the vlan support and native vlan from the
REAP group.

A value of 'true' indicates that the AP should inherit
the vlan support and native vlan from…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.2.1.1.8

cLReapApVlanIdTable

table
.1.3.6.1.4.1.9.9.517.1.2.2 · 1 row entry · 4 columns
Open in standard view 
This table represents the WLAN / VLAN Id mappings to be
configured for the REAP identified by
cLApSysMacAddress.
          
VLAN Id configured through this table is passed to
the respective REAP through the 'Add WLAN' LWAPP
message, sent as part of the 'Configure Response
message from the controller to the REAP, during
the initialization of the REAP. The REAP maps
the VLAN to the particular WLAN to locally switch
the data packets when those APs are in standalone
mode.  Thus, the information added through this
table is applicable for REAPs only.
          
VLANs are configured on WLANs for which local
switching of packets is enabled through
cLReapWlanEnLocalSwitching.  This means that
a row is added to this table only if there
are WLANs available on the controller with
local switching enabled and the AP is a REAP.
cLReapApVlanIdEntry entry .1.3.6.1.4.1.9.9.517.1.2.2.1
Each entry represents a conceptual row that
corresponds to one WLAN / VLAN Id mapping to
be applied to the REAP identified by
cLApSysMacAddress.
Indexes
CISCO-LWAPP-AP-MIBcLApSysMacAddress CISCO-LWAPP-WLAN-MIBcLWlanIndex
Column Syntax OID
cLReapApVlanId
This object specifies the VLAN ID to be mapped
to the WLAN identified by cLWlanIndex.
Unsigned32r/w
Constraints:
range: 1-4095
 .1.3.6.1.4.1.9.9.517.1.2.2.1.1
cLReapApVlanInheritance
This object specifies the inheritance to be mapped
to the WLAN identified by cLWlanIndex.

A value of 'ap' specifies VLAN for that WLAN is
inherited from AP spcific configuration

A value of…
Enumerationr/w
Enumerated Values:
1ap
2hreapGroup
3wlan
 .1.3.6.1.4.1.9.9.517.1.2.2.1.2
cLReapApVlanRowStatus
This object specifies the rowstatus of the
wlan vlan mappings table
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.2.2.1.3
cLReapApVlanUsedBySecEthInterface
This object indicates if vlan represented by
cLReapApVlanId is used by any of the secondary
ethernet interface when the REAP AP is in
flex+bridge mode.

A value of 'true' indicates cLReapApVlanId is
used …
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.2.2.1.4

cLReapApVlanIdAclTable

table
.1.3.6.1.4.1.9.9.517.1.2.3 · 1 row entry · 5 columns
Open in standard view 
This table represents the VLAN Id- ACL mappings to be
configured for the REAP identified by 
cLApSysMacAddress.
cLReapApVlanIdAclEntry entry .1.3.6.1.4.1.9.9.517.1.2.3.1
Each entry represents a conceptual row that
corresponds to one VLAN Id - ACL mapping to
be applied to the REAP identified by
cLApSysMacAddress.
Indexes
CISCO-LWAPP-AP-MIBcLApSysMacAddress cLReapVlanId
Column Syntax OID
cLReapVlanId
This object represents the VLAN ID to be mapped
to the ACL for the access point identified by
cLApSysMacAddress.
Unsigned32
Constraints:
range: 1-4095
 .1.3.6.1.4.1.9.9.517.1.2.3.1.1
cLReapIngressAcl
This object specifies the name of the ingress Access
Control List for the vlan-acl mapping.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.2.3.1.2
cLReapEgressAcl
This object specifies the name of the egress
Access Control List for the vlan-acl mapping.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.2.3.1.3
cLReapApVlanIdAclRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.2.3.1.4
cLReapVlanIdAclType
This object represents the type of the vlan acl mapping

A value of 'apSource' indicates that vlan-acl mapping
applied from AP level.

A value of 'groupSource' indicates that vlan-acl mappin…
Enumeration
Enumerated Values:
1apSource
2groupSource
 .1.3.6.1.4.1.9.9.517.1.2.3.1.5

cLReapApWlanAclTable

table
.1.3.6.1.4.1.9.9.517.1.2.4 · 1 row entry · 2 columns
Open in standard view 
This table represents the WLAN ACL mappings to be
configured for the REAP identified by
cLApSysMacAddress.
A row is added to this table only if there
are WLANs available on the controller with
local switching enabled and the AP is a REAP.
cLReapApWlanAclEntry entry .1.3.6.1.4.1.9.9.517.1.2.4.1
Each entry represents a conceptual row that
corresponds to one WLAN / ACL mapping to
be applied to the REAP identified by
cLApSysMacAddress.
Indexes
CISCO-LWAPP-AP-MIBcLApSysMacAddress CISCO-LWAPP-WLAN-MIBcLWlanIndex
Column Syntax OID
cLReapApWebAuthAcl
This object specifies the webauth ACL name to be
mapped to the WLAN identified by cLWlanIndex.

This will be applied to REAP AP only when
webauth client associates to REAP AP.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.2.4.1.1
cLReapApWebAuthAclRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.2.4.1.2

cLReapWebPolicyAclTable

table
.1.3.6.1.4.1.9.9.517.1.2.5 · 1 row entry · 2 columns
Open in standard view 
This table represents the web policies associated with
an AP. Entries are added or deleted by the user
through the use of cLReapWebPolicyRowStatus.
cLReapWebPolicyAclEntry entry .1.3.6.1.4.1.9.9.517.1.2.5.1
Each entry represents a conceptual row in
cLReapWebPolicyAclTable.
Indexes
CISCO-LWAPP-AP-MIBcLApSysMacAddress cLReapWebPolicyAcl
Column Syntax OID
cLReapWebPolicyAcl
This object represents the name of the web policy
ACL to be mapped to the access point identified
by cLApSysMacAddress.
OctetString
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.2.5.1.1
cLReapWebPolicyAclRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.2.5.1.2

cLReapApLocalSplitACLTable

table
.1.3.6.1.4.1.9.9.517.1.2.6 · 1 row entry · 2 columns
Open in standard view 
This table represents the WLAN - local split ACL
mappings to be configured for the REAP AP 
identified by cLApSysMacAddress.
cLReapApLocalSplitACLEntry entry .1.3.6.1.4.1.9.9.517.1.2.6.1
Each entry represents a conceptual row that
corresponds to one WLAN- local split ACL mapping
to be applied to the REAP identified by
cLApSysMacAddress.
Indexes
CISCO-LWAPP-AP-MIBcLApSysMacAddress CISCO-LWAPP-WLAN-MIBcLWlanIndex
Column Syntax OID
cLReapApLocalSplitAcl
This object specifies the local split ACL name to be
mapped to the WLAN identified by cLWlanIndex.

This is applicable only for central switching WLANs on
REAP AP
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.2.6.1.1
cLReapApLocalSplitAclRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.2.6.1.2

cLReapApCentralDhcpTable

table
.1.3.6.1.4.1.9.9.517.1.2.7 · 1 row entry · 5 columns
Open in standard view 
This object represents the behavior of the REAP
AP when switching the DHCP packets of the clients
associated to it through the WLAN identified
by cLWlanIndex.
cLReapApCentralDhcpEntry entry .1.3.6.1.4.1.9.9.517.1.2.7.1
This object represents the behavior of the REAP
AP when switching the DHCP packets of the clients
associated to it through the WLAN identified
by cLWlanIndex.
Indexes
CISCO-LWAPP-AP-MIBcLApSysMacAddress CISCO-LWAPP-WLAN-MIBcLWlanIndex
Column Syntax OID
cLReapApDhcpCentral
This object specifies the behavior of the REAP AP
when switching the DHCP frames of the clients
associated to it through the WLAN identified
by cLWlanIndex.

A value of 'true' specifies REAP AP will tunnel…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.2.7.1.1
cLReapApDhcpOverrideDNS
This object specifies the behavior of the REAP AP
when switching the DNS frames of the clients
associated to it through the WLAN identified
by cLWlanIndex.

A value of 'true' specifies REAP AP will tunnel
…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.2.7.1.2
cLReapApNatPatEnabled
This object specifies whether Network Address
Translation (NAT) and Port Address Trnaslation (PAT)
are enabled on this REAP AP for the WLAN identified
by cLWlanIndex.

A value of 'true' specifies REAP AP w…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.2.7.1.3
cLReapApDhcpRowStatus
This object represents the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.2.7.1.4
cLReapApInheritance
This object represents the inheritance level
of central DHCP configuration. It can be inherted
from AP or REAP group or WLAN configuration
SNMP-FRAMEWORK-MIBSnmpAdminString
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.2.7.1.5

cLReapApL2AclTable

table
.1.3.6.1.4.1.9.9.517.1.2.8 · 1 row entry · 2 columns
Open in standard view 
This table represents the L2 ACL mappings to be
configured for the REAP AP identified by
cLApSysMacAddress.
A row is added to this table only if there
are WLANs available on the controller with
local switching enabled and the AP is a REAP.
cLReapApL2AclEntry entry .1.3.6.1.4.1.9.9.517.1.2.8.1
Each entry represents a conceptual row that
corresponds to one WLAN / L2 ACL mapping to
be applied to the REAP identified by
cLApSysMacAddress.
Indexes
CISCO-LWAPP-AP-MIBcLApSysMacAddress CISCO-LWAPP-WLAN-MIBcLWlanIndex
Column Syntax OID
cLReapApL2Acl
This object specifies the L2ACL name to be
mapped to the WLAN identified by cLWlanIndex
for this REAP AP
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.2.8.1.1
cLReapApL2AclRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.2.8.1.2

cLReapGroupConfigTable

table
.1.3.6.1.4.1.9.9.517.1.3.1 · 1 row entry · 55 columns
Open in standard view 
This table represents the configuration for
REAPs so that the APs can be configured as a 
group.
Entries are added or deleted by the user through
the use of cLReapGroupRowStatus.
cLReapGroupConfigEntry entry .1.3.6.1.4.1.9.9.517.1.3.1.1
Each entry represents a conceptual row in
cLReapGroupConfigTable.
Indexes
cLReapGroupName
Column Syntax OID
cLReapGroupName
This object represents REAP group name and
uniquely identifies an entry in cLReapGroupConfigTable.
OctetString
Constraints:
range: 1-64
 .1.3.6.1.4.1.9.9.517.1.3.1.1.1
cLReapGroupPrimaryRadiusIndex
The object specifies the value that maps to the
primary RADIUS server for this group.

A value of '0' indicates that the primary RADIUS
server is not configured for this group.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.517.1.3.1.1.2
cLReapGroupSecondaryRadiusIndex
The object specifies the value that maps to the
secondary RADIUS server for this group.

A value of '0' indicates that the secondary RADIUS
server is not configured for this group.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.517.1.3.1.1.3
cLReapGroupStorageType
This object specifies the storage type for this conceptual
row.
SNMPv2-TCStorageTyper/w
Textual Convention: SNMPv2-TCStorageType Enumeration
Type Values:
1other
2volatile
3nonVolatile
4permanent
5readOnly
 .1.3.6.1.4.1.9.9.517.1.3.1.1.4
cLReapGroupRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.3.1.1.5
cLReapGroupRadiusPacTimeout deprecated
This object represents timeout value for the
PAC (protected access credentials). Superceded
by cLReapGroupRadiusPacTimeoutCtrl.
SecondsUnsigned32r/w
Constraints:
range: 0-4095
 .1.3.6.1.4.1.9.9.517.1.3.1.1.6
cLReapGroupRadiusAuthorityId
This object specifies the authority ID used
for client association when client uses EAP-FAST
mechanism.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.1.1.7
cLReapGroupRadiusAuthorityInfo
This object specifies the authority information
used for client association when client uses
EAP-FAST mechanism.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.1.1.8
cLReapGroupRadiusServerKey
This object specifies the RADIUS server key. For security
the key always returns '****'.
OctetStringr/w
Constraints:
range: 1-32
 .1.3.6.1.4.1.9.9.517.1.3.1.1.9
cLReapGroupRadiusIgnoreKey
This object specifies whether anonymous provisioning
is enabled. A value of 'true' indicates the controller
will ignore the key configured in cLReapGroupRadiusServerKey
anonymous requests. A value of 'false'
indicate…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.10
cLReapGroupRadiusEnable
This parameter specifies whether RADIUS is enabled.
A value of 'true' specifies that RADIUS is enabled.
A value of 'false' specifies that RADIUS is disabled.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.11
cLReapGroupRadiusLeapEnable
This parameter specifies whether LEAP is enabled.
A value of 'true' specifies that LEAP is enabled.
A value of 'false' specifies that LEAP is disabled.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.12
cLReapGroupRadiusEapFastEnable
This parameter specifies whether EAP-FAST is enabled.
A value of 'true' specifies that EAP-FAST is enabled.
A value of 'false' specifies that EAP-FAST is disabled.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.13
cLReapGroupRadiusPacTimeoutCtrl
This parameter specifies timeout value for the
PAC (protected access credentials).
Valid range of timeout is 2 to 4095,
and value 0 stands for disable.
secondsUnsigned32r/w
Constraints:
range: 0-4095
 .1.3.6.1.4.1.9.9.517.1.3.1.1.14
cLReapGroupEfficientApUpgradeEnable
This parameter specifies whether efficient AP image
upgrade is enabled. A value of 'true' indicates that
efficient AP image upgrade is enabled. A value of 'false'
indicates that Efficient AP image upgrade is disabled.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.15
cLReapGroupApUpgradeStart
This object specifies which image REAP AP has to download
from WLC upon upgrade start.

A value of 'initiatePrimary' specifies AP will download
primary image from WLC.

A value of 'initiateBa…
Enumerationr/w
Enumerated Values:
1initiatePrimary
2initiateBackup
3abort
 .1.3.6.1.4.1.9.9.517.1.3.1.1.16
cLReapGroupSlaveMaxRetryCount
This object specifies the maximum retries the
the slave AP has to try to download image
from the master in the hreap group before it
stars download from WLC. Range is 1 to 63
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.517.1.3.1.1.17
cLReapGroupPrimaryRadiusServerType
This object specifies server IP address type of the
primary radius server for the flexconnect group.
INET-ADDRESS-MIBInetAddressTyper/w
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.9.517.1.3.1.1.18
cLReapGroupPrimaryRadiusServerAddress
This object specifies server IP address of the
primary radius server for the flexconnect group.
INET-ADDRESS-MIBInetAddressr/w
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.3.1.1.19
cLReapGroupPrimaryRadiusServerPort
This object specifies port number of the primary
radius server for the flexconnect group.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.517.1.3.1.1.20
cLReapGroupPrimaryServerSecret
This object specifies secret of the primary radius
server for the flexconnect group.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.3.1.1.21
cLReapGroupSecRadiusServerType
This object specifies server IP address type of the
secondary radius server for the flexconnect group.
INET-ADDRESS-MIBInetAddressTyper/w
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.9.517.1.3.1.1.22
cLReapGroupSecRadiusServerAddress
This object specifies server IP address of the
secondary radius server for the flexconnect group.
INET-ADDRESS-MIBInetAddressr/w
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.3.1.1.23
cLReapGroupSecRadiusServerPort
This object specifies port number of the secondary
radius server for the flexconnect group.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.517.1.3.1.1.24
cLReapGroupSecServerSecret
This object specifies secret of the secondary
radius server for the flexconnect group.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.3.1.1.25
cLReapGroupRadiusPeapEnable
This parameter specifies whether PEAP is enabled for
that flexconect group.
A value of 'true' indicates that PEAP is enabled.
A value of 'false' indicates that PEAP is disabled.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.26
cLReapGroupRadiusEapTlsEnable
This parameter specifies whether EAP-TLS is enabled
in the flexconect group.
A value of 'true' indicates that EAP-TLS is enabled.
A value of 'false' indicates that EAP-TLS is disabled.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.27
cLReapGroupCertificateEapTlsEnable
This parameter specifies whether certificate for
EAP-TLS is enabled.
A value of 'true' indicates that EAP-TLS certificate
is enabled.
A value of 'false' indicates that EAP-TLS certificate
is disabled.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.28
cLReapGroupNativeVlanId
This object specifies the Native VLAN ID for the
particular flexconenct group identified by
cLReapGroupName.
Unsigned32r/w
Constraints:
range: 1-4095
 .1.3.6.1.4.1.9.9.517.1.3.1.1.29
cLReapGroupVlanEnable
This object specifies the availability of Native
VLAN configured through cLReapGroupNativeVlanId on
this REAP group.

A value of 'true' indicates that the VLAN configured
as native through cLReapGroupNativ…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.30
cLReapGroupOverrideVlanEnable
This object specifies the overriding of vlans at REAP
APs by the vlans available from the reap group.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.31
cLReapGroupHttpProxyIpType
Thsi object specifies Ip Address type of Http proxy in
flexconnect group.
INET-ADDRESS-MIBInetAddressTyper/w
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.9.517.1.3.1.1.32
cLReapGroupHttpProxyIp
This object specifies HTTP proxy Ip address in
flexconect group.
INET-ADDRESS-MIBInetAddressr/w
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.3.1.1.33
cLReapGroupHttpProxyPort
This object specifies HTTP Proxy port in flexconnect
group.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.517.1.3.1.1.34
cLReapGroupVlanTemplateName
This object specifies the vlan template name at REAP
APs by the vlans available from the reap group.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.3.1.1.35
cLReapGroupEfficientApJoinEnable
This parameter specifies whether efficient AP image
join is enabled. A value of 'true' indicates that
efficient AP image upgrade is enabled. A value of 'false'
indicates that Efficient AP image upgrade is disabled.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.36
cLReapGroupRadiusServerGroupName
This object specifies the radius server group name entry in
cLReapGroupConfigTable.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.3.1.1.37
cLReapGroupEapFastProfileName
This object specifies the eap fast profile used for
local auth in cLReapGroupConfigTable.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.3.1.1.38
cLReapGroupArpCacheEnabled
This object specifies whether ARP cache feature is enabled
for the flexconnect Access Points connected to the
Wireless LAN Controller.
A Value of 'True' specifies that ARP cache is enabled.
A Value of 'False' specifies …
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.39
cLReapGroupHomeApEnable
This object specifies if the APs connected to this
profile/group are used as Home APs.
A value of 'true' specifies that REAP AP is a Home AP.
A value of 'false' specifies that this REAP AP is not a
Home AP.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.40
cLReapGroupLeastLatencyJoinEnable
This object specifies if this REAP AP should join
controller which has least latency.
A value of 'true' specifies that this REAP AP will
join controller which has least latency.
A value of 'false' specifies that this RE…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.41
cLReapGroupHomeApLocalSsidReset
This object can be used to reset local SSID on a Home AP.
A value of true specifies that the local SSID is to be reset.
A value of false on this during set will return error.
A value of false will be returned on get.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.42
cLReapGroupInstallMappingRadioBackhaul
This object specifies if WLANs are enabled or disabled on
backhaul radio.

A value of true specifies that wlan mapping would be enabled
on backhaul radio.

A value of false specifies that wla…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.43
cLReapGroupResilientMode
This object specifies if Standalone mode support is
enabled or disabled on a REAP AP.

A value of true specifies that Standalone mode would
be enabled on backhaul radio.

A value of false spe…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.44
cLReapGroupDescription
This object specifies the description of flex profile
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.1.1.45
cLReapGroupFallbackRadioShutEnabled
This object specifies whether Fallback Radio Shut feature
is enabled for the flexconnect Access Points connected to
the Wireless LAN Controller.

A value of true specifies that Fallback Radio Shut feature
…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.46
cLReapCtsInlineTagging
This object specifies whether cts inline tagging feature is
enabled for the flexconnect Access Points connected to the
Wireless LAN Controller.
A Value of 'true' specifies that cts inline tagging is enabled.
A Value of …
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.48
cLReapIsHomeApEnable
This object specifies whether OEAP is enabled.
A value of 'true' enable OEAP
A value of 'false' disable OEAP
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.49
cLReapCtsRolebasedEnforcement
This object specifies whether cts role-based enforcement
feature is enabled for the flexconnect Access Points connected
to the Wireless LAN Controller.
A Value of 'true' specifies that cts role-based enforcement is
enab…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.50
cLReapCtsSxpAttachedProfileName
This object specifies the sxp profile attached to the flex
profile
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.3.1.1.51
cLReapGroupAccountingRadiusServerGroupName
This object specifies the Radius server group for accounting attached
to the flex profile
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.3.1.1.52
cLReapLocalRoaming
This object specifies whether local roaming feature is enabled for
the FlexConnect Access Points connected to the Wireless LAN Controller.
A Value of 'true' specifies that local roaming is enabled.
A Value of 'false' sp…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.53
cLReapGroupMdnsFlexProfileName
This object specifies the mdns flex profile name entry in
cLReapGroupConfigTable.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.3.1.1.54
cLReapIpOverlap
This object specifies whether IP overlap feature is enabled for
the FlexConnect Access Points connected to the Wireless LAN Controller.
A Value of 'true' specifies that IP overlap is enabled.
A Value of 'false' specifie…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.55
cLReapGroupDhcpBroadcastEnable
This object specifies whether DHCP broadcast for locally
switched clients is enabled or disabled.
A value of 'true' specifies that DHCP broadcast is enabled.
A value of 'false' specifies that DHCP broadcast is disabled.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.1.1.56

cLReapGroupApConfigTable

table
.1.3.6.1.4.1.9.9.517.1.3.2 · 1 row entry · 4 columns
Open in standard view 
This table represents the group associated with
an AP. Entries are added or deleted by the user 
through the use of cLReapGroupApRowStatus.
cLReapGroupApConfigEntry entry .1.3.6.1.4.1.9.9.517.1.3.2.1
Each entry represents a conceptual row in
cLReapGroupApConfigTable.
Indexes
cLReapGroupName CISCO-LWAPP-AP-MIBcLApSysMacAddress
Column Syntax OID
cLReapGroupApStorageType
This object specifies the storage type for this conceptual
row.
SNMPv2-TCStorageTyper/w
Textual Convention: SNMPv2-TCStorageType Enumeration
Type Values:
1other
2volatile
3nonVolatile
4permanent
5readOnly
 .1.3.6.1.4.1.9.9.517.1.3.2.1.1
cLReapGroupApRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.3.2.1.2
cLReapGroupApEntryType
This object represents the entry type of the AP.
A value of 'admin' represents the AP added to group
by manual admin configuration
A value of 'cloud' represents the AP added to group
because of AP configured from cloud …
Enumeration
Enumerated Values:
1admin
2cloud
 .1.3.6.1.4.1.9.9.517.1.3.2.1.3
cLReapGroupApPnPConflict
This object represents whether there is any conflict
with the flexconnect group value from PnP.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.2.1.4

cLReapGroupUserConfigTable

table
.1.3.6.1.4.1.9.9.517.1.3.3 · 1 row entry · 4 columns
Open in standard view 
This table represents the group associated with
an User. Entries are added or deleted by the 
application through the use of 
cLReapGroupUserRowStatus.
cLReapGroupUserConfigEntry entry .1.3.6.1.4.1.9.9.517.1.3.3.1
Each entry represents a conceptual row in
cLReapGroupUserConfigTable.
Indexes
cLReapGroupName cLReapGroupUserName
Column Syntax OID
cLReapGroupUserName
This object represents the user name for this
group. user name is used for authenticating a
client associated to an AP within the group.
OctetString
Constraints:
range: 1-24
 .1.3.6.1.4.1.9.9.517.1.3.3.1.1
cLReapGroupUserPassword
This object specifies the password for this
user.
OctetStringr/w
Constraints:
range: 1-64
 .1.3.6.1.4.1.9.9.517.1.3.3.1.2
cLReapGroupUserStorageType
This object specifies the storage type for this
conceptual row.
SNMPv2-TCStorageTyper/w
Textual Convention: SNMPv2-TCStorageType Enumeration
Type Values:
1other
2volatile
3nonVolatile
4permanent
5readOnly
 .1.3.6.1.4.1.9.9.517.1.3.3.1.3
cLReapGroupUserRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.3.3.1.4

cLReapGroupVlanAclTable

table
.1.3.6.1.4.1.9.9.517.1.3.4 · 1 row entry · 5 columns
Open in standard view 
This table represents the configuration of VLAN-ACL
mappings for REAP groups.
cLReapGroupVlanAclEntry entry .1.3.6.1.4.1.9.9.517.1.3.4.1
Each entry represents a conceptual row in
cLReapGroupVlanAclTable.
Indexes
cLReapGroupName cLReapGroupVlanId
Column Syntax OID
cLReapGroupVlanId
This object represents the VLAN ID to be mapped
to the ACL for the reap group identified by
cLReapGroupName
Unsigned32
Constraints:
range: 1-4095
 .1.3.6.1.4.1.9.9.517.1.3.4.1.1
cLReapGroupIngressAcl
This object specifies the name of the ingress access
control list for the vlan-acl mapping for the group
identified by cLReapGroupName.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.4.1.2
cLReapGroupEgressAcl
This object specifies the name of the egress access
control list for the vlan-acl mapping for the group
identified by cLReapGroupName.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.4.1.3
cLReapGroupVlanAclRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.3.4.1.4
cLReapGroupVlanOrder
This object represents the vlan order configuration on the
group level.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.517.1.3.4.1.5

cLReapGroupAclTable

table
.1.3.6.1.4.1.9.9.517.1.3.5 · 1 row entry · 3 columns
Open in standard view 
This table represents the configuration of wlan-acl
mappings for REAPs.
cLReapGroupAclEntry entry .1.3.6.1.4.1.9.9.517.1.3.5.1
Each entry represents a conceptual row in
cLReapGroupAclTable.
Indexes
cLReapGroupName CISCO-LWAPP-WLAN-MIBcLWlanIndex
Column Syntax OID
cLReapGroupWebAuthAcl
This object specifies the name of the webauth access
control list for the wlan-acl mapping in the flexconnect
group.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.5.1.1
cLReapGroupAclRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.3.5.1.2
cLReapGroupWebAuthIpv6Acl
This object specifies the name of the Ipv6 webauth access
control list for the wlan-acl mapping in the flexconnect
group.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.5.1.3

cLReapGroupWebPolicyAclTable

table
.1.3.6.1.4.1.9.9.517.1.3.6 · 1 row entry · 4 columns
Open in standard view 
This table represents the configuration of webpolicy
acl mappings for REAP groups.
cLReapGroupWebPolicyAclEntry entry .1.3.6.1.4.1.9.9.517.1.3.6.1
Each entry represents a conceptual row in the
cLReapGroupWebPolicyAclTable.
Indexes
cLReapGroupName cLReapGroupWebPolicyAcl
Column Syntax OID
cLReapGroupWebPolicyAcl
This object specifies the name of the webpolicy access
control aist to be mapped to the REAP group.
OctetString
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.6.1.1
cLReapGroupWebPolicyAclRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.3.6.1.2
cLReapGroupWebPolicyAclType
This object specifies whether webpolicy access control list
is IPv4 or IPv6.
Enumerationr/w
Enumerated Values:
1ipv4
2ipv6
 .1.3.6.1.4.1.9.9.517.1.3.6.1.3
cLReapGroupWebPolicyAclCentWebAuth
This object represents whether to Configure central-webauth
for this ACL.
A value of true specifies that central-webauth is enabled for
ACL.
A value of false specifies that central-webauth is disabled
for ACL.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.6.1.4

cLReapGroupLocalSplitAclTable

table
.1.3.6.1.4.1.9.9.517.1.3.7 · 1 row entry · 2 columns
Open in standard view 
This table represents the configuration of WLAN-ACL
mappings for local split tunneling at REAP groups.
cLReapGroupLocalSplitAclEntry entry .1.3.6.1.4.1.9.9.517.1.3.7.1
Each entry represents a conceptual row in
cLReapGroupLocalSplitAclTable.
Indexes
cLReapGroupName CISCO-LWAPP-WLAN-MIBcLWlanIndex
Column Syntax OID
cLReapGroupLocalSplitAcl
This object specifies the name of the local split
access control list to be mapped to the WLAN inside
REAP group
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.7.1.1
cLReapGroupLocalSplitAclRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.3.7.1.2

cLReapGroupCentralDhcpTable

table
.1.3.6.1.4.1.9.9.517.1.3.8 · 1 row entry · 4 columns
Open in standard view 
This table represents the configuration of central
dhcp processing for REAP APs in REAP groups
cLReapGroupCentralDhcpEntry entry .1.3.6.1.4.1.9.9.517.1.3.8.1
Each entry represents a conceptual row in
cLReapGroupCentralDhcpTable.
Indexes
cLReapGroupName CISCO-LWAPP-WLAN-MIBcLWlanIndex
Column Syntax OID
cLReapGroupDhcpCentral
This object specifies the behavior of the REAP AP
part of REAP group when switching the DHCP frames of
the clients associated to it through the WLAN identified
by cLWlanIndex.

A value of 'true' specifies …
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.8.1.1
cLReapGroupDhcpOverrideDNS
This object specifies the behavior of the REAP AP
part of REAP group when switching the DNS frames
of the clients associated to it through the WLAN
identified by cLWlanIndex.

A value of 'true' specifies…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.8.1.2
cLReapGroupNatPatEnabled
This object specifies whether Network Address
Translation (NAT) and Port Address Trnaslation (PAT)
are enabled on this REAP AP part of REAP group for
the WLAN identified by cLWlanIndex.

A value of 'true'…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.8.1.3
cLReapGroupDhcpRowStatus
This object represents the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.3.8.1.4

cLReapGroupVlanIdTable

table
.1.3.6.1.4.1.9.9.517.1.3.9 · 1 row entry · 2 columns
Open in standard view 
This table represents the WLAN / VLAN Id mappings
to be configured for the REAP identified by
REAP group name.
          
VLAN Id configured through this table is passed to
the respective REAP group identified by the 
REAP group name.
cLReapGroupVlanIdEntry entry .1.3.6.1.4.1.9.9.517.1.3.9.1
Each entry represents a conceptual row that
corresponds to one WLAN / VLAN Id mapping to
be applied to the REAP identified by
cLReapGroupName.
Indexes
cLReapGroupName CISCO-LWAPP-WLAN-MIBcLWlanIndex
Column Syntax OID
cLReapGroupWlanVlanId
This object specifies the VLAN ID to be mapped
to the WLAN identified by cLWlanIndex in the REAP
group.
Unsigned32r/w
Constraints:
range: 1-4095
 .1.3.6.1.4.1.9.9.517.1.3.9.1.1
cLReapGroupVlanRowStatus
This object specifies the reap group vlan mapping row
status.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.3.9.1.2

cLReapGroupAVCFlexTable

table
.1.3.6.1.4.1.9.9.517.1.3.10 · 1 row entry · 3 columns
Open in standard view 
This table represents the WLAN / AVC parameters
mappings to be configured for the REAP identified by
REAP group name.
          
AVC parameters configured through this table is passed 
to the respective REAP group identified by the 
REAP group name.
cLReapGroupAVCFlexEntry entry .1.3.6.1.4.1.9.9.517.1.3.10.1
Each entry represents a conceptual row that
corresponds to one WLAN / AVC parameters mapping to
be applied to the REAP identified by
cLReapGroupName.
Indexes
cLReapGroupName CISCO-LWAPP-WLAN-MIBcLWlanIndex
Column Syntax OID
cLReapGroupAVCFlexProfileName
This object specifies the AVC profile name assigned
to this WLAN in the REAP idendified by cLReapGroupName.
'none' specifies no profile is being associated.
profile name 'none' should be used to de-associate profile
fr…
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.10.1.1
cLReapGroupNbarStatsVisibilityEnable
This object specifies the user to enable or disable
NBAR stats visibility.
A value of 'disable' indicates NBAR stats visibility
is disabled.
A value of 'enable' indicates NBAR stats visibility
is enabled.
A value of 'w…
Enumerationr/w
Enumerated Values:
1disable
2enable
3wlan-specific
 .1.3.6.1.4.1.9.9.517.1.3.10.1.2
cLReapGroupAVCFlexRowStatus
This object specifies the rowstatus of the reap
group wlan avc parameter mappings table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.3.10.1.3

cLReapGroupVlanNameAclTable

table
.1.3.6.1.4.1.9.9.517.1.3.11 · 1 row entry · 7 columns
Open in standard view 
This table defines the VLAN Name- ACL mappings to be
configured for the REAP identified by cLReapGroupVlanName.
cLReapGroupVlanNameAclEntry entry .1.3.6.1.4.1.9.9.517.1.3.11.1
Each entry represents a conceptual row that corresponds to
one VLAN Name - ACL mapping to be applied to the REAP
identified by cLReapGroupVlanName.
Indexes
cLReapGroupName cLReapGroupVlanName
Column Syntax OID
cLReapGroupVlanName
This object specifies the name of the Vlan name
for the vlan-acl mapping.
OctetString
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.11.1.1
cLReapGroupVlanIdentifier
This object specifies the VLAN ID to be mapped to the Acl for
the Access Point identified by cLReapGroupVlanName.
Unsigned32r/w
Constraints:
range: 1-4096
 .1.3.6.1.4.1.9.9.517.1.3.11.1.2
cLReapGroupAcl
This object specifies the name of the Access Control List
for the vlan-acl mapping.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.11.1.3
cLReapGroupVlanNameAclType
This object specifies the type of the vlan acl mapping
apSource - vlan-acl mapping applied from AP level.
groupSource - vlan-acl mapping applied from hreap group
level.
Enumeration
Enumerated Values:
1apSource
2groupSource
 .1.3.6.1.4.1.9.9.517.1.3.11.1.4
cLReapGroupVlanNameAclRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.3.11.1.5
cLReapGroupAclIn
This object specifies the name of the Ingress Access
Control List for the vlan-acl mapping.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.11.1.6
cLReapGroupAclOut
This object specifies the name of the Egress Access
Control List for the vlan-acl mapping.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.3.11.1.7

cLReapGroupCtsSxpTable

table
.1.3.6.1.4.1.9.9.517.1.3.12 · 1 row entry · 9 columns
Open in standard view 
This table defines the CTS SXP configured for the REAP
identified by cLReapCtsSxpConfigProfileName.
cLReapGroupCtsSxpEntry entry .1.3.6.1.4.1.9.9.517.1.3.12.1
Each entry represents a conceptual row that corresponds to
one CTS SXP configuration be applied to the REAP identified by
cLReapGroupCtsSxp.
Indexes
cLReapCtsSxpConfigProfileName
Column Syntax OID
cLReapCtsSxpConfigProfileName
This object specifies the cts sxp configuration profile name
for the flex connect Access Points connected to the
Wireless LAN controller.
OctetString
Constraints:
range: 1-32
 .1.3.6.1.4.1.9.9.517.1.3.12.1.1
cLReapCtsSxpDefaultPassword
This object specifies the cts sxp configuration Default
password for the flex connect Access Points connected to the
wireless LAN controller.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.3.12.1.2
cLReapCtsSxpState
This object specifies if the SXP (Security Group Tag Exchange
Protocol) functionality is enabled for the flex connect Access
Points connected to the wireless LAN controller.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.3.12.1.3
cLReapCtsSxpListenerMinHoldTime
This object specifies the minimum hold-time for
SXP connections in 'listener' mode.

Value of this object must be lesser than
ctsxSxpListenerMaxHoldTime.
secondsUnsigned32r/w
Constraints:
range: 1-65534
 .1.3.6.1.4.1.9.9.517.1.3.12.1.4
cLReapCtsSxpListenerMaxHoldTime
This object specifies the maximum hold-time for
SXP connections in 'listener' mode.

Value of this object must be greater than
ctsxSxpListenerMinHoldTime.
secondsUnsigned32r/w
Constraints:
range: 1-65534
 .1.3.6.1.4.1.9.9.517.1.3.12.1.5
cLReapCtsSxpReconcilePeriod
This object specifies the amount of time after which system
will initiate removal of SGT mappings for a reconciled
connection.

A value of zero for this object indicates that SGT
mappings for a reconciled …
secondsUnsigned32r/w
Constraints:
range: 0-64000
 .1.3.6.1.4.1.9.9.517.1.3.12.1.6
cLReapCtsSxpRetryPeriod
This object specifies the amount of time after which the
device will make the retry attempt for the SXP connections
that are not setup successfully.

A value of zero for this object indicates that the devi…
secondsUnsigned32r/w
Constraints:
range: 0-64000
 .1.3.6.1.4.1.9.9.517.1.3.12.1.7
cLReapCtsSxpSpeakerMinHoldTime
This object specifies the minimum hold-time for SXP
connections in 'speaker' mode.
secondsUnsigned32r/w
Constraints:
range: 1-65534
 .1.3.6.1.4.1.9.9.517.1.3.12.1.8
cLReapCtsSxpRowStatus
This object specifies the conceptual status of the
row.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.3.12.1.9

cLReapCtsSxpPeerTable

table
.1.3.6.1.4.1.9.9.517.1.3.13 · 1 row entry · 5 columns
Open in standard view 
A list of SXP peers configured on this device.
It is a list of IP addresses of respective
SXP connection peers configured for this device.
SXP peers exchange security group tags information
of clients through SxpV4 protocol.
cLReapCtsSxpPeerEntry entry .1.3.6.1.4.1.9.9.517.1.3.13.1
An entry containing management information of a
particular SXP peers.
Indexes
cLReapCtsSxpConfigProfileName cLReapCtsSxpPeerIpType cLReapCtsSxpPeerIp
Column Syntax OID
cLReapCtsSxpPeerIpType
The type of Internet address of the peer SXP device.
INET-ADDRESS-MIBInetAddressType
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.9.517.1.3.13.1.1
cLReapCtsSxpPeerIp
The Internet address of the SXP peer device. The type of this
address is determined by the value of cLReapCtsSxpPeerIpType
object.
OctetString
Constraints:
range: 1-64
 .1.3.6.1.4.1.9.9.517.1.3.13.1.2
cLReapCtsSxpMode
This object specifies the device mode of this SXP connection.

A value of 'speaker' indicates that device will acts as
the speaker in this SXP connection.

A value of 'listener' indicates tha…
Enumerationr/w
Enumerated Values:
1speaker
2listener
3both
 .1.3.6.1.4.1.9.9.517.1.3.13.1.3
cLReapCtsSxpPeerPassword
This object specifies to configure the
password of the sxp peer device.
Enumerationr/w
Enumerated Values:
0notRequired
2default
 .1.3.6.1.4.1.9.9.517.1.3.13.1.4
cLReapCtsSxpPeerRowStatus
This object specifies the conceptual status of the
row.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.3.13.1.5

cLReapAclTable

table
.1.3.6.1.4.1.9.9.517.1.4.1 · 1 row entry · 4 columns
Open in standard view 
The table represents REAP ACLs (access control lists)
on the switch.
cLReapAclEntry entry .1.3.6.1.4.1.9.9.517.1.4.1.1
Each entry represents the attributes for clReapAclTable.
An entry gets added to the table on creating a
flexconnect ACL.
Indexes
cLReapAclName
Column Syntax OID
cLReapAclName
This object represents name of the REAP
access control list.
OctetString
Constraints:
range: 1-32
 .1.3.6.1.4.1.9.9.517.1.4.1.1.1
cLReapAclApplyMode
This object specifies the apply mode of the ACL on the
switch.
Mode value 'applied' means the ACL has been
applied on the switch.
Mode value 'notapplied' means the ACL not applied
on the switch.
Enumeration
Enumerated Values:
0notapplied
1applied
 .1.3.6.1.4.1.9.9.517.1.4.1.1.2
cLReapAclRowStatus
This object specifies the row Status of the ACL.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.4.1.1.3
cLReapAclUrlDomainListType deprecated
This object specifies the List type for all the urls
being confiured on the acl. blackList indicates, access
to all the urls configured will be denied and whiteList
indicates permit. Default value is blackList.
Enumerationr/w
Enumerated Values:
1blackList
2whiteList
 .1.3.6.1.4.1.9.9.517.1.4.1.1.4

cLReapAclRuleTable

table
.1.3.6.1.4.1.9.9.517.1.4.2 · 1 row entry · 18 columns
Open in standard view 
The table represents ACL Rules(access control list
entries) on the ACL with name cLReapAclName.
cLReapAclRuleEntry entry .1.3.6.1.4.1.9.9.517.1.4.2.1
Each entry represents the attributes for
clReapAclRuleTable. An entry gets added to
the table on creating a rule on flexconnect
ACL.
Indexes
cLReapAclName cLReapAclRuleIndex
Column Syntax OID
cLReapAclRuleIndex
This object represents index of the ACL rule. This can
be updated to reset the sequence of the rules of an ACL.
Unsigned32
Constraints:
range: 1-64
 .1.3.6.1.4.1.9.9.517.1.4.2.1.1
cLReapAclRuleAction
This object specifies permission mode of the rule.
A value of 'deny' specifies client traffic matches
this rule will be blocked.
A value of 'permit' specifies client traffic matches
this rule will be allowed to pass thr…
Enumerationr/w
Enumerated Values:
0deny
1permit
 .1.3.6.1.4.1.9.9.517.1.4.2.1.2
cLReapAclRuleSourceIpAddressType
This object specifies source IP address type of
the ACL rule. The value is limited to ipv4 only.
INET-ADDRESS-MIBInetAddressTyper/w
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.9.517.1.4.2.1.3
cLReapAclRuleSourceIpAddress
The object specifies source IP address of the ACL
rule. It cab be any ipv4 source address.
A value 0 implies any sourse address.
INET-ADDRESS-MIBInetAddressr/w
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.4.2.1.4
cLReapAclRuleSourceIpNetmaskType
This object specifies source IP netmask type of
the ACL rule. The value is limited to ipv4 only.
INET-ADDRESS-MIBInetAddressTyper/w
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.9.517.1.4.2.1.5
cLReapAclRuleSourceIpNetmask
This object specifies source IP netmask of the
ACL rule. A value '0' implies any source mask.
INET-ADDRESS-MIBInetAddressr/w
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.4.2.1.6
cLReapAclRuleDestinationIpAddressType
This object specifies destination IP address type of
the ACL rule. The value is limited to ipv4 only.
INET-ADDRESS-MIBInetAddressTyper/w
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.9.517.1.4.2.1.7
cLReapAclRuleDestinationIpAddress
The object specifies destination IP address of the ACL
rule. It cab be any ipv4 source address. A value '0'
implies any destination address.
INET-ADDRESS-MIBInetAddressr/w
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.4.2.1.8
cLReapAclRuleDestinationIpNetmaskType
This object specifies destination IP netmask type of
the ACL rule. The value is limited to ipv4 only.
INET-ADDRESS-MIBInetAddressTyper/w
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.9.517.1.4.2.1.9
cLReapAclRuleDestinationIpNetmask
This object specifies destination IP netmask of the
ACL rule. A value '0' implies any destination mask.
INET-ADDRESS-MIBInetAddressr/w
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.4.2.1.10
cLReapAclRuleProtocol
This object specifies protocol of the packet.
It can be either of the pre specified protocols like
TCP, UDP, ICMP, ESP, AH, GRE, IP, Ethernet Over IP,
OSPF or any number between 0 and 255.
A value 256 implies that thi…
Unsigned32r/w
Constraints:
range: 0-256
 .1.3.6.1.4.1.9.9.517.1.4.2.1.11
cLReapAclRuleStartSourcePort
This object specifies source port of the packet.
It can be either of the pre specified ports like HTTP,
HTTPS, Telnet, RADIUS etc or any number between 0 and
65535. A value 65536 implies that this rule applies
to 'Any'…
Unsigned32r/w
Constraints:
range: 0-65536
 .1.3.6.1.4.1.9.9.517.1.4.2.1.12
cLReapAclRuleEndSourcePort
This object specifies source port of the packet.
It can be either of the pre specified ports like HTTP,
HTTPS, Telnet, RADIUS etc or any number between 0 and
65535. A value 65536 implies that this rule applies
to 'Any'…
Unsigned32r/w
Constraints:
range: 0-65536
 .1.3.6.1.4.1.9.9.517.1.4.2.1.13
cLReapAclRuleStartDestinationPort
This object specifies destination port of the packet.
It can be either of the pre specified ports like HTTP,
HTTPS, Telnet, RADIUS etc or any number between 0 and
65535. A value 65536 implies that this rule applies
to …
Unsigned32r/w
Constraints:
range: 0-65536
 .1.3.6.1.4.1.9.9.517.1.4.2.1.14
cLReapAclRuleEndDestinationPort
This object specifies destination port of the packet.
It can be either of the pre specified ports like HTTP,
HTTPS, Telnet, RADIUS etc or any number between 0 and
65535. A value 65536 implies that this rule applies
to …
Unsigned32r/w
Constraints:
range: 0-65536
 .1.3.6.1.4.1.9.9.517.1.4.2.1.15
cLReapAclRuleDscp
This object specifies DSCP value of the rule.
A value 256 implies 'Any'.
Unsigned32r/w
Constraints:
range: 0-256
 .1.3.6.1.4.1.9.9.517.1.4.2.1.16
cLReapAclNewRuleIndex
This object specifies new index of the ACL rule.
This attribute should be updated if the requirement is
to reset the sequence of the rules of an ACL. A read
on this will yield the same value as cLReapAclRuleIndex.
Unsigned32r/w
Constraints:
range: 1-64
 .1.3.6.1.4.1.9.9.517.1.4.2.1.17
cLReapAclRuleRowStatus
This object specifies row status of the ACL rule.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.4.2.1.18

cLReapL2AclTable

table
.1.3.6.1.4.1.9.9.517.1.4.3 · 1 row entry · 3 columns
Open in standard view 
The table listing layer2 ACLs (access control lists)
on the switch.
cLReapL2AclEntry entry .1.3.6.1.4.1.9.9.517.1.4.3.1
Each entry represents the attributes for
cLReapL2AclTable.An entry gets added to the
table on creating a layer2 ACL.
Indexes
cLReapL2AclName
Column Syntax OID
cLReapL2AclName
This object represents name of the L2 ACL on the
switch.
OctetString
Constraints:
range: 1-32
 .1.3.6.1.4.1.9.9.517.1.4.3.1.1
cLReapL2AclApplyMode
This object represents the apply mode of the L2ACL on
the switch.
Mode value 'applied' means the L2ACL has been
applied on the switch.
Default mode on creation on ACL will be notapplied.
Enumeration
Enumerated Values:
1notapplied
2applied
 .1.3.6.1.4.1.9.9.517.1.4.3.1.2
cLReapL2AclRowStatus
This object specifies the row Status of the L2ACL.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.4.3.1.3

cLReapL2AclRuleTable

table
.1.3.6.1.4.1.9.9.517.1.4.4 · 1 row entry · 7 columns
Open in standard view 
The table represents L2Acl rules(access control list
entries) on the L2ACL with name cLReapL2AclName.
cLReapL2AclRuleEntry entry .1.3.6.1.4.1.9.9.517.1.4.4.1
Each entry represents the attributes for
clReapL2AclRuleTable. An entry gets added to
the table on creating a rule on L2ACL.
Indexes
cLReapL2AclName cLReapL2AclRuleIndex
Column Syntax OID
cLReapL2AclRuleIndex
This object represents the unique index of the L2ACL rule
in REAP L2ACL. This can be updated to reset the sequence
of the rules of an L2ACL. Valid range for this object is
1 to 64
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.517.1.4.4.1.1
cLReapL2AclRuleAction
This object specifies the permission mode of a rule.
The value of 'deny' means traffic will be blocked
which meets the rule.
The value of 'permits' means traffic will be allowed
which meets the rule.
Enumerationr/w
Enumerated Values:
1deny
2permit
 .1.3.6.1.4.1.9.9.517.1.4.4.1.2
cLReapL2AclRuleEthertype
This object specifies the etherType of the L2Acl
rule. Default is 0x0
Unsigned32r/w
Constraints:
range: 0-65536
 .1.3.6.1.4.1.9.9.517.1.4.4.1.3
cLReapL2AclRuleEthertypeMask
This object specifies the etherType Mask of the
L2Acl rule. Default is 0x0
Unsigned32r/w
Constraints:
range: 0-65536
 .1.3.6.1.4.1.9.9.517.1.4.4.1.4
cLReapL2AclRuleDirection
This object specifies the direction of the packet
to which the rule may be applied.
A value of 'inbound' specifies that this rule will be
applied on traffic coming into switchport.
A value of 'outbound' specifies that …
Enumerationr/w
Enumerated Values:
1inbound
2outbound
3any
 .1.3.6.1.4.1.9.9.517.1.4.4.1.5
cLReapL2AclNewRuleIndex
This object specifies the new Index of the L2ACL rule.
This attribute should be updated if the requirement is
to reset the sequence of the rules of an ACL. A read
on this will yield the same value as cLReapL2AclRuleIn…
Unsigned32r/w
Constraints:
range: 1-64
 .1.3.6.1.4.1.9.9.517.1.4.4.1.6
cLReapL2AclRuleRowStatus
This object specifies the status of a conceptual
row in the ACL Rule Table. This is used to create
and delete entries in the table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.4.4.1.7

cLReapAclUrlDomainRuleTable

table
.1.3.6.1.4.1.9.9.517.1.4.5 · 1 row entry · 4 columns
Open in standard view 
This table represents url domain acl Rules
(url based Access Control List entries) on the 
 ACL with name cLReapAclName.
cLReapAclUrlDomainRuleEntry entry .1.3.6.1.4.1.9.9.517.1.4.5.1
Each Entry represents the attributes for
cLReapAclUrlDomainRuleTable. An Url domain rule
entry gets added to the table on creating
a rule on flexconnect ACL.
Indexes
cLReapAclName cLReapAclUrlDomainRuleIndex
Column Syntax OID
cLReapAclUrlDomainRuleIndex
This object specifies the index of the Url domain
ACL rule. It can be used to reset the sequence of
the Url rules of an ACL.
Unsigned32
Constraints:
range: 1-20
 .1.3.6.1.4.1.9.9.517.1.4.5.1.1
cLReapAclUrlDomainRuleUrl
This object specifies the URL name for the
url domain rule.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.4.5.1.2
cLReapAclUrlDomainRuleAction
This object specifies the permission mode of url domain
rule.
A value of 'deny' specifies client traffic matches
this rule will be blocked.
A value of 'permit' specifies client traffic matches
this rule …
Enumerationr/w
Enumerated Values:
1deny
2permit
 .1.3.6.1.4.1.9.9.517.1.4.5.1.3
cLReapAclUrlDomainRuleRowStatus
This is the status column for this row and is
used to create and delete specific instances of
rows in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.4.5.1.4

cLReapUrlDomainListTable

table
.1.3.6.1.4.1.9.9.517.1.4.6 · 1 row entry · 8 columns
Open in standard view 
This table represents url domain acl Rules(url based Access
Control List entries) on the ACL with name cLReapUrlListName.
cLReapUrlDomainListEntry entry .1.3.6.1.4.1.9.9.517.1.4.6.1
Each Entry represents the attributes for
cLReapUrlDomainListTable.
An Url domain rule entry gets added to the table on creating
a rule on flexconnect ACL.
Indexes
cLReapUrlListName
Column Syntax OID
cLReapUrlListName
This object specifies the URL name for the url domain rule.
OctetString
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.4.6.1.1
cLReapUrlDomainRuleAction
This object specifies the permission mode of url domain rule.
This is set through the url domain list type in the acl.
Enumeration
Enumerated Values:
1deny
2permit
 .1.3.6.1.4.1.9.9.517.1.4.6.1.2
cLReapUrlRedirectServerIpv4Type
This object specifies the type of the source IP address of
the ACL rule.
INET-ADDRESS-MIBInetAddressTyper/w
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.9.517.1.4.6.1.3
cLReapUrlRedirectServerIpv4
This object specifies the source IP address of the ACL rule.
INET-ADDRESS-MIBInetAddressr/w
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.4.6.1.4
cLReapUrlRedirectServerIpv6Type
This object specifies the type of the source IP address of the
ACL rule.
INET-ADDRESS-MIBInetAddressTyper/w
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.9.517.1.4.6.1.5
cLReapUrlRedirectServerIpv6
This object specifies the source IP address of the ACL rule.
INET-ADDRESS-MIBInetAddressr/w
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.4.6.1.6
cLReapUrlDomainRuleRowStatus
This is the status column for this row and is used to
create and delete specific instances of rows in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.4.6.1.7
cLReapUrlFilterID
This object specifies the filter ID (an unique reference
number) for urlfilter lists created.
Unsigned32
Constraints:
range: 1-16
 .1.3.6.1.4.1.9.9.517.1.4.6.1.8

cLReapUrlDomainRulesTable

table
.1.3.6.1.4.1.9.9.517.1.4.7 · 1 row entry · 2 columns
Open in standard view 
This table represents url domain acl Rules(url based Access
Control List entries) on the ACL with name cLReapUrlListName.
cLReapUrlDomainRulesEntry entry .1.3.6.1.4.1.9.9.517.1.4.7.1
Each Entry represents the attributes for
cLReapUrlDomainListTable.
An Url domain rule entry gets added to the table on creating
a rule on flexconnect ACL.
Indexes
cLReapUrlListName cLReapUrlDomainRuleUrl
Column Syntax OID
cLReapUrlDomainRuleUrl
This object specifies the URL name for the url domain rule.
OctetString
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.517.1.4.7.1.1
cLReapUrlRowStatus
This object specifies the row Status of the url
table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.4.7.1.2

cLReapEnhancedUrlDomainListTable

table
.1.3.6.1.4.1.9.9.517.1.4.8 · 1 row entry · 2 columns
Open in standard view 
This table represents enhanced URL domain ACLs(URL based Access
Control List entries).
cLReapEnhancedUrlDomainListEntry entry .1.3.6.1.4.1.9.9.517.1.4.8.1
Each Entry represents the attributes for
cLReapEnhancedUrlDomainListTable.
Indexes
cLReapEnhancedUrlDomainListName
Column Syntax OID
cLReapEnhancedUrlDomainListName
This object specifies name for the enhanced URL domain ACL
OctetString
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.4.8.1.1
cLReapEnhancedUrlDomainListRowStatus
This is the status column for this row and is
used to create and delete specific instances of
rows in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.4.8.1.2

cLReapEnhancedUrlDomainRulesTable

table
.1.3.6.1.4.1.9.9.517.1.4.9 · 1 row entry · 4 columns
Open in standard view 
This table represents URL domain rules on the ACL with 
name cLReapEnhancedUrlDomainListName.
cLReapEnhancedUrlDomainRulesEntry entry .1.3.6.1.4.1.9.9.517.1.4.9.1
Each Entry represents the attributes for
URL domain rule.
Indexes
cLReapEnhancedUrlDomainListName cLReapEnhancedUrlDomainRuleUrl
Column Syntax OID
cLReapEnhancedUrlDomainRuleUrl
This object specifies the URL name for the URL domain rule.
OctetString
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.517.1.4.9.1.1
cLReapEnhancedUrlDomainRuleAction
This object specifies the permission mode of url domain
rule.
A value of 'deny' specifies client traffic matches
this rule will be blocked.
A value of 'permit' specifies client traffic matches
this rule …
Enumerationr/w
Enumerated Values:
1deny
2permit
 .1.3.6.1.4.1.9.9.517.1.4.9.1.2
cLReapEnhancedUrlDomainRulePreference
This object specifies the preference of the URL domain
rule.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.517.1.4.9.1.3
cLReapEnhancedUrlDomainRuleRowStatus
This is the status column for this row and is
used to create and delete specific instances of
rows in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.4.9.1.4

cLReapMasterApConfigTable

table
.1.3.6.1.4.1.9.9.517.1.5.1 · 1 row entry · 3 columns
Open in standard view 
This table represents the master AP admin
configuration of REAPs.
          
The agent adds a row to this table corresponding to
each row representing a REAP in cLApTable of the
CISCO-LWAPP-AP-MIB.  The agent deletes the row
either when the AP dissociates from the
controller or moved out of the remote mode.
cLReapMasterApConfigEntry entry .1.3.6.1.4.1.9.9.517.1.5.1.1
Each entry represents a conceptual row in
cLReapMasterApConfigTable and corresponds to the
Master configuration of a REAP.
Indexes
cLReapGroupName CISCO-LWAPP-AP-MIBcLApSysMacAddress
Column Syntax OID
cLReapMasterApModel
The object represents the model of the AP in the
hreap group. This AP will be the master in the efficient
upgrade process.
SNMP-FRAMEWORK-MIBSnmpAdminString
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.5.1.1.1
cLReapMasterApManual
This object represents if this REAP AP is
manually configured by the user.
A value of 'true' indicates that this REAP master is
manually configured.
A value of 'false' indicates that this REAP master is
not manually con…
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.517.1.5.1.1.2
cLReapMasterApRowStatus
This object specifies the row Status of the Master
table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.5.1.1.3

cLReapIpv6AclTable

table
.1.3.6.1.4.1.9.9.517.1.7.1 · 1 row entry · 3 columns
Open in standard view 
The table listing ACLs (Access Control Lists) on the
device.
cLReapIpv6AclEntry entry .1.3.6.1.4.1.9.9.517.1.7.1.1
Each entry in this table provides information about
one ACL of the controller.
Indexes
cLReapIpv6AclName
Column Syntax OID
cLReapIpv6AclName
This object represents name of the Access Control List.
OctetString
Constraints:
range: 1-32
 .1.3.6.1.4.1.9.9.517.1.7.1.1.1
cLReapIpv6AclApplyMode
This object represents whether IPv6 ACL is applied or not.
A value of notapplied (1) indicates that, ACL has not been
applied on the device.
A value of applied (2) indicates that, ACL has been applied
on the device.
Enumeration
Enumerated Values:
1notapplied
2applied
 .1.3.6.1.4.1.9.9.517.1.7.1.1.2
cLReapIpv6AclRowStatus
This is the status column for this row and is used to create
and delete specific instance of row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.7.1.1.3

cLReapIpv6AclRuleTable

table
.1.3.6.1.4.1.9.9.517.1.7.2 · 1 row entry · 16 columns
Open in standard view 
The table represents the ACL rules
(Access Control List Entries).
cLReapIpv6AclRuleEntry entry .1.3.6.1.4.1.9.9.517.1.7.2.1
Each entry in this table provides information about
one ACL rule of the controller.
Indexes
cLReapIpv6AclName cLReapIpv6AclRuleIndex
Column Syntax OID
cLReapIpv6AclRuleIndex
This object represents a unique ACL rule. This
can be updated by using cLReapIpv6AclNewRuleIndex
to reset the sequence of the rules of an ACL.
Unsigned32
Constraints:
range: 1-64
 .1.3.6.1.4.1.9.9.517.1.7.2.1.1
cLReapIpv6AclRuleAction
This object specifies the permission mode of a rule.
A value of deny(1) indicates that, rule is to be
denied.
A value of permit(2) indicates that, rule is to be
permit.
Enumerationr/w
Enumerated Values:
1deny
2permit
 .1.3.6.1.4.1.9.9.517.1.7.2.1.2
cLReapIpv6AclRuleSourceAddressType
This object specifies the type of the source
IP address of the ACL rule.
INET-ADDRESS-MIBInetAddressTyper/w
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.9.517.1.7.2.1.3
cLReapIpv6AclRuleSourceAddress
This object specifies the source IP address.
INET-ADDRESS-MIBInetAddressr/w
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.7.2.1.4
cLReapIpv6AclRuleSourcePrefixLength
This object specifies the prefix length for source
IP address.
r/w .1.3.6.1.4.1.9.9.517.1.7.2.1.5
cLReapIpv6AclRuleDestinationAddressType
This object specifies the type of the destination IP address.
INET-ADDRESS-MIBInetAddressTyper/w
Textual Convention: INET-ADDRESS-MIBInetAddressType Enumeration
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.9.517.1.7.2.1.6
cLReapIpv6AclRuleDestinationAddress
This object specifies the destination IP address.
INET-ADDRESS-MIBInetAddressr/w
Textual Convention: INET-ADDRESS-MIBInetAddress OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.7.2.1.7
cLReapIpv6AclRuleDestinationPrefixLength
This object specifies the prefix length for destination
IP address.
r/w .1.3.6.1.4.1.9.9.517.1.7.2.1.8
cLReapIpv6AclRuleProtocol
This object specifies protocol of the packet. It can
be either of the pre specified protocols like TCP, UDP,
ICMP, ESP, AH, GRE,IP, ethernet over IP, OSPF or any
number between 0 and 255. A value 256 implies that this…
Unsigned32r/w
Constraints:
range: 0-256
 .1.3.6.1.4.1.9.9.517.1.7.2.1.9
cLReapIpv6AclRuleStartSourcePort
This object specifies the start source port of the
packet. It can be either of the pre specified ports
like HTTP, HTTPS, Telnet, RADIUS etc or any number
between 0 and 65535.
r/w .1.3.6.1.4.1.9.9.517.1.7.2.1.10
cLReapIpv6AclRuleEndSourcePort
This object specifies the end Source Port of the packet.
It can be either of the pre specified ports like HTTP,
HTTPS, Telnet, RADIUS etc or any number between 0 and
65535.
r/w .1.3.6.1.4.1.9.9.517.1.7.2.1.11
cLReapIpv6AclRuleStartDestinationPort
This object specifies the start Destination Port of the
packet. It can be either of the pre specified ports like HTTP,
HTTPS, Telnet, RADIUS etc or any number between 0 and 65535.
r/w .1.3.6.1.4.1.9.9.517.1.7.2.1.12
cLReapIpv6AclRuleEndDestinationPort
This object specifies the End Destination Port of the packet.
It can be either of the pre specified ports like HTTP, HTTPS,
Telnet, RADIUS etc or any number between 0 and 65535.
r/w .1.3.6.1.4.1.9.9.517.1.7.2.1.13
cLReapIpv6AclRuleDscp
This object specifies the DSCP value of the rule.
A value 256 implies Any.
Unsigned32r/w
Constraints:
range: 0-256
 .1.3.6.1.4.1.9.9.517.1.7.2.1.14
cLReapIpv6AclNewRuleIndex
This object specifies the new Index of the ACL rule. This
object should be updated if the requirement is to reset the
sequence of the rules of an ACL.
Unsigned32r/w
Constraints:
range: 1-64
 .1.3.6.1.4.1.9.9.517.1.7.2.1.15
cLReapIpv6AclRuleRowStatus
This is the status column for this row and is used to create
and delete specific instances of rows in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.7.2.1.16

cLReapIpv6AclUrlDomainRuleTable

table
.1.3.6.1.4.1.9.9.517.1.7.3 · 1 row entry · 4 columns
Open in standard view 
This table represents url domain ACL Rules(url
based Access Control List entries) on the ACL 
with name cLReapIpv6AclName.
cLReapIpv6AclUrlDomainRuleEntry entry .1.3.6.1.4.1.9.9.517.1.7.3.1
Each Entry represents the attributes for
cLReapIpv6AclUrlDomainRuleTable. An Url Domain
rule entry gets added to the table on creating
a rule on flexconnect ACL.
Indexes
cLReapIpv6AclName cLReapIpv6AclUrlDomainRuleIndex
Column Syntax OID
cLReapIpv6AclUrlDomainRuleIndex
This object specifies the index of the Url domain
Ipv6 ACL rule. It can be used to reset the sequence
of the Url rules of an ACL.
Unsigned32r/w
Constraints:
range: 1-20
 .1.3.6.1.4.1.9.9.517.1.7.3.1.1
cLReapIpv6AclUrlDomainRuleUrl
This object specifies the URL name for the
url domain rule.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.517.1.7.3.1.2
cLReapIpv6AclUrlDomainRuleAction
This object specifies the permission mode of url domain rule.
A value of 'deny(1)' specifies client traffic matches
this rule will be blocked.
A value of 'permit(2)' specifies client traffic matches
this rule will be al…
Enumerationr/w
Enumerated Values:
1deny
2permit
 .1.3.6.1.4.1.9.9.517.1.7.3.1.3
cLReapIpv6AclUrlDomainRuleRowStatus
This is the status column for this row and is
used to create and delete specific instances of
rows in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.7.3.1.4

cLReapVlanIdNameMapTable

table
.1.3.6.1.4.1.9.9.517.1.8.1 · 1 row entry · 3 columns
Open in standard view 
This table defines the VLAN Id- Vlan Name mappings to
be configured for the REAP identified by group/profile
Name.
cLReapVlanIdNameMapEntry entry .1.3.6.1.4.1.9.9.517.1.8.1.1
Each entry represents a conceptual row that corresponds to
one VLAN name-Id mapping to be applied to the REAP identified
by template name.
Indexes
cLReapGroupVlanTemplateName cLReapVlanName
Column Syntax OID
cLReapVlanName
This object specifies the vlan name
for the vlan name-id mapping.
OctetString
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.8.1.1.1
cLReapVlanMapId
This object specifies the VLAN ID for the
particular template.
Unsigned32r/w
Constraints:
range: 1-4095
 .1.3.6.1.4.1.9.9.517.1.8.1.1.2
cLReapVlanIdNameMapRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.8.1.1.3

cLReapVlanTemplateTable

table
.1.3.6.1.4.1.9.9.517.1.8.2 · 1 row entry · 2 columns
Open in standard view 
This table defines the template table configured for the
REAP identified by template Name.
cLReapVlanTemplateEntry entry .1.3.6.1.4.1.9.9.517.1.8.2.1
Each entry represents a conceptual row that corresponds to
one VLAN name-Id mapping to be applied to the REAP identified
by template name.
Indexes
cLReapGroupVlanTemplateName
Column Syntax OID
cLReapVlanTemplateDescription
This object specifies the description of the template.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.9.9.517.1.8.2.1.1
cLReapVlanTemplateRowStatus
This object specifies the status column for a
conceptual row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.517.1.8.2.1.2