ARICENT-CFA-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
20
Rows
20
Columns
131

ifMainTable

table
.1.3.6.1.4.1.2076.27.1.4 · 1 row entry · 24 columns
Open in standard view 
A list of all the interface entries in the system. 
This table contains objects which are applicable to all
types of interfaces in the system. This table is a 
proprietary extension to the standard ifTable and 
ifXTable. The index to this table has the semantics of
the MIB-2 ifIndex.
ifMainEntry entry .1.3.6.1.4.1.2076.27.1.4.1
An entry containing management information applicable
to a particular interface.
Indexes
ifMainIndex
Column Syntax OID
ifMainIndex
A unique value, greater than zero, for each
interface. This object is identical to the ifIndex
of the standard MIB-2 ifTable.
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.2076.27.1.4.1.1
ifMainType
The type/protocol of interface. Specification of
the object is mandatory for all interfaces. This
value should be specified after the row creation
in the ifMainTable and before setting any other
object in this table. On…
Enumerationr/w
Enumerated Values:
5rfc877x25
6ethernetCsmacd
9iso88025TokenRing
23ppp
24softwareLoopback
32frameRelay
38miox25
49aal5
53propVirtual
84async
92frameRelayMPI
108pppMultilinkBundle
114ipOverAtm
118hdlc
131tunnel
134atmSubInterface
136l3ipvlan
150mplsTunnel
161ieee8023ad
166mpls
200teLink
209brgPort
246ifPwType
247ilan
248pip
 .1.3.6.1.4.1.2076.27.1.4.1.2
ifMainMtu
The MTU for the interface as shown to the higher
interface sub-layer (this value should not include
the encapsulation or header added by the interface).
If IP is operating over the interface, then this
value indicates …
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.2076.27.1.4.1.3
ifMainAdminStatus
The desired state of the interface. This object
can be set only when the ifMainRowStatus of the
interface is active. This object has the semantics
of the ifAdminStatus of the standard ifTable.

The testing…
Enumerationr/w
Enumerated Values:
1up
2down
3testing
4loopback
 .1.3.6.1.4.1.2076.27.1.4.1.4
ifMainOperStatus
The current operational state of the interface.
The testing (3) state indicates that no operational
packets can be passed - this state is not supported
currently.

If ifMainAdminStatus is down (2)
then if…
Enumeration
Enumerated Values:
1up
2down
3testing
4unknown
5dormant
6notPresent
7lowerLayerDown
 .1.3.6.1.4.1.2076.27.1.4.1.5
ifMainEncapType
The encapsulation type to be used over the interface.

For Ethernet interfaces, the default encapsulation
type is ethernetV2(8). The other possible encapsulation
is llcSnap(6). If other(1) is specified the…
Enumerationr/w
Enumerated Values:
1other
2nlpid
3nlpidSnap
4cudNlpid
5cudNlpidSnap
6llcSnap
7vcMultiplexed
8ethernetV2
 .1.3.6.1.4.1.2076.27.1.4.1.6
ifMainBrgPortType
The Bridge port type of this specified switch port.
Bridge Port type can be specified only for switch ports and not for
router ports, IVR interfaces and I-LAN Interfaces.

providerNetworkPort - Port Conne…
Enumerationr/w
Enumerated Values:
1providerNetworkPort
2customerNetworkPortPortBased
3customerNetworkPortStagged
4customerEdgePort
5propCustomerEdgePort
6propCustomerNetworkPort
7propProviderNetworkPort
8customerBridgePort
9customerNetworkPortCtagged
10virtualInstancePort
11providerInstancePort
12customerBackbonePort
13uplinkAccessPort
14stationFacingBridgePort
 .1.3.6.1.4.1.2076.27.1.4.1.7
ifMainRowStatus
A RowStatus variable for addition, deletion and in-activation
of the interfaces. Specification of the object is mandatory
for all interfaces.

When the status is active, the interface is created and
ready …
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.2076.27.1.4.1.8
ifMainSubType
This object stores the subType value of the specified interface.
Configuration of this object is not mandatory.By default
Sub type value will be updated based on the hardware link speed.

For non Ethernet …
Enumerationr/w
Enumerated Values:
251extremeEther
252fastEther
253gigabitEthernet
254xlEthernet
255notApplicable
 .1.3.6.1.4.1.2076.27.1.4.1.9
ifMainNetworkType
This object indicates whether this interface is a
WAN or LAN link.

The default value for this object varies according
to the interface type. All interfaces of type radio (71),
ieee8023ad (161) and l3ipvl…
Enumerationr/w
Enumerated Values:
1lan
2wan
 .1.3.6.1.4.1.2076.27.1.4.1.10
ifMainWanType
This object indicates whether this interface is a
private or public WAN link.

This object is applicable only for PPP interfaces and
ethernet WAN interfaces. For other interfaces the value
cannot be set …
Enumerationr/w
Enumerated Values:
0other
1private
2public
 .1.3.6.1.4.1.2076.27.1.4.1.11
ifMainDesc
A textual string which contains the description about an interface.
SNMPv2-TCDisplayStringr/w
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.2076.27.1.4.1.12
ifMainStorageType
The storage type for this conceptual row in the ifMainTable.
Conceptual rows having the value 'permanent' need not allow
write-access to any columnar object in the row.
only volatile and nonVolatile are allowed for thi…
SNMPv2-TCStorageTyper/w
Textual Convention: SNMPv2-TCStorageType Enumeration
Type Values:
1other
2volatile
3nonVolatile
4permanent
5readOnly
 .1.3.6.1.4.1.2076.27.1.4.1.13
ifMainExtSubType
This object stores the subType value of the specified interface.
These sub types are specified for the ifMainType-propVirtual.
Enumerationr/w
Enumerated Values:
0sisp
1attachmentCircuit
2openflow
 .1.3.6.1.4.1.2076.27.1.4.1.14
ifMainPortRole
This object is for indicating the port role for each interface.

A port is termed as uplink port when it is connected to the
network.

A port is termed as downlink when it is connected towar…
Enumerationr/w
Enumerated Values:
1uplink
2downlink
 .1.3.6.1.4.1.2076.27.1.4.1.15
ifMainUfdOperStatus
This object is for indicating the Uplink Failure Detection(UFD)
port operational status for each interface.

Uplink Failure Detection(UFD) operational status of the uplink
port is same as the operationa…
Enumeration
Enumerated Values:
1up
2down
3ufdErrorDisabled
 .1.3.6.1.4.1.2076.27.1.4.1.16
ifMainUfdGroupId
An identifier that uniquely identifies the group. Each group has
uplink interfaces to monitor and downlink interfaces to disable.
The UFD group Id value zero indicates that the port is not
present in any group. By setti…
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.2076.27.1.4.1.17
ifMainUfdDownlinkDisabledCount deprecated
A counter which indicates the number of times
that downlink ports in the group were automatically
disabled because of all uplink ports failure in the group.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.1.4.1.18
ifMainUfdDownlinkEnabledCount deprecated
A counter which indicates the number of times
that downlink ports in the group were automatically
enabled because of any one uplink ports back to function in the group.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.1.4.1.19
ifMainDesigUplinkStatus
This object specifies whether this interface is designated uplink
or not.

A port is termed as designated uplink when the port is connected
to the network and it has more preference over all the uplink
p…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.2076.27.1.4.1.20
ifMainEncapDot1qVlanId
This object specifies the VLAN identifier assigned to Layer 3
Subinterface for association in the porting layer. This object
is available only when the interface is set as Layer3 SubInterface.
Integer32r/w
Constraints:
range: 0-4094
 .1.3.6.1.4.1.2076.27.1.4.1.21
ifMainNeighborId
A string identifying the device connected to the interface.
The neighbor ID is derived from LLDP data that is currently
associated with the interface.
OctetString
Constraints:
range: 0-255
 .1.3.6.1.4.1.2076.27.1.4.1.22
ifMainName
A string identifying the device interface that can
be used to unambiguously identify the interface when
configuring interface settings in various tables
that identify ports by name.
OctetString
Constraints:
range: 0-32
 .1.3.6.1.4.1.2076.27.1.4.1.23
ifMainPrevDesc
A textual string which contains the previous
description for the interface.
OctetString
Constraints:
range: 0-255
 .1.3.6.1.4.1.2076.27.1.4.1.24

ifIpTable

table
.1.3.6.1.4.1.2076.27.1.5 · 1 row entry · 10 columns
Open in standard view 
A list of all the interface entries in the system which
are registered with IP.
                
This table contains objects which are applicable for the
management of IP over the network interfaces
in the system. 
             
This table is a extension to the ifMainTable. 
The index to this table has the semantics of
the ifMainIndex of the ifMainTable.
                
Entries are created automatically in this table for
any interface sub-layer which is layer below IP using
the ifStackTable. Similarly, entries are deleted from
this table when the interface's layering below IP is
removed.
ifIpEntry entry .1.3.6.1.4.1.2076.27.1.5.1
An entry containing management information applicable
to a particular interface over which IP is operating.
Indexes
ifMainIndex
Column Syntax OID
ifIpAddrAllocMethod
The mechanism to be used for allocation of IP
address for this interface.

The value negotiation can be used only for PPP
and MLPPP interfaces which support obtaining of
IP addresses through negotiation.
…
Enumerationr/w
Enumerated Values:
1manual
2negotiation
3dynamic
4none
 .1.3.6.1.4.1.2076.27.1.5.1.1
ifIpAddr
Specifies the IP address given to this
interface. The specification of this object is
mandatory for all network interfaces (Ethernet,
FR VC, IPoA interface, PPP link - not under MP,
MP interface and X.25 VC). If the int…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.27.1.5.1.2
ifIpSubnetMask
Specifies the IP Subnet Mask for this
interface. The value should be specified only
for network interfaces and any valid VLSM is
accepted.

If not specified, this object takes the default
subnet mask valu…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.27.1.5.1.3
ifIpBroadcastAddr
Specifies the IP broadcast address for this
interface. The value should be specified only
for network interfaces and any valid broadcast
address based on a valid VLSM is accepted.

If not specified, this …
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.27.1.5.1.4
ifIpForwardingEnable
Specifies whether IP forwarding is enable on
this interface. Disabling IP forwarding on an
interface will result in packets which are to
be forwarded on that interface being dropped
and ICMP error messages being generat…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.2076.27.1.5.1.5
ifIpAddrAllocProtocol
Specifies the protocol to be used to obtain
IP address for this interface. This object is
valid only when ifIpAddrAllocMethod is set to
dynamic (3).

When ifIpAddrAllocMethod option is dhcp(2)
dhcp-cli…
Enumerationr/w
Enumerated Values:
1rarp
2dhcp
 .1.3.6.1.4.1.2076.27.1.5.1.6
ifIpDestMacAddress
The unicast Peer MacAddress for unnumbered interface.
This Object needs to be configured mandatorily for proper
forwarding of IP packets over unnumbered interfaces.This object
needs to be set to avoid ARP resolution fai…
SNMPv2-TCMacAddressr/w
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.2076.27.1.5.1.7
ifIpUnnumAssocIPIf
This object stores the interface index of the interface associated
with the unnumbered interface. The source IP addresses used over
the Unnumbered interface in relation to the destination IP address
are borrowed from th…
IF-MIBInterfaceIndexr/w
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.2076.27.1.5.1.8
ifIpIntfStatsEnable
This object specifies whether statistics collection is enabled on the IP
interface.

When the status is set to True, statistics collection will be started on the IP interface.
Retrieval of statistics on…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.2076.27.1.5.1.9
ifIpPortVlanId
This object specifies the VLAN identifier assigned to router-ports
for association in the porting layer. This object is meant for the
chipsets when the porting layer demands VLAN identifier association
to realize route…
Integer32r/w
Constraints:
range: 0-4094
 .1.3.6.1.4.1.2076.27.1.5.1.10

ifWanTable

table deprecated
.1.3.6.1.4.1.2076.27.1.6 · 1 row entry · 13 columns
Open in standard view 
A list of all the WAN interfaces in the system.
          
This table contains objects which are applicable for the
management of WAN interfaces like PPP, MP bundle and
FR/X.25/ATM VCs in the system.
             
This table is a extension to the ifMainTable. 
The index to this table has the semantics of
the ifMainIndex of the ifMainTable.
                
Entries are created automatically in this table when
any WAN interface is created in the ifMainTable. The 
ppp(23), miox25(38), frameRelayMPI(92), 
pppMultilinkBundle(108) and atmSubInterface(134)
interfaces have entries in this table. The entries
in this table are deleted when the interfaces are
deleted from the ifMainTable.
ifWanEntry entry .1.3.6.1.4.1.2076.27.1.6.1
An entry containing management information applicable
to a WAN interface.
Indexes
ifMainIndex
Column Syntax OID
ifWanInterfaceType deprecated
The type of the WAN interface. This is
same as if MIB-2 ifType and ifMainType.
Enumeration
Enumerated Values:
23ppp
38miox25
92frameRelayMPI
108pppMultilinkBundle
134atmSubInterface
 .1.3.6.1.4.1.2076.27.1.6.1.1
ifWanConnectionType deprecated
The type of WAN connection. This object
will not be applicable to PPP and MLPPP
interfaces and will have the value other(0).
For all other interfaces the default value
is permanent(1).

It is possible to …
Enumerationr/w
Enumerated Values:
0other
1permanent
2switched
 .1.3.6.1.4.1.2076.27.1.6.1.2
ifWanVirtualPathId deprecated
The VPI for ATM VCs. This object
will not be applicable to other
interfaces and will have the value 0.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.2076.27.1.6.1.3
ifWanVirtualCircuitId deprecated
The VCI for ATM VCs, DLCI for Frame Relay VCs and
the channel identifier for X.25 VCs.

For SVCs this object is read-only, the value will be
assigned after the SVC establishment.

This objec…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.2076.27.1.6.1.4
ifWanPeerMediaAddress deprecated
The Media Address of the peer to whom this
connection is to be established.

For ATM VCs this can be in E.164, NSAP or either of these along
with the subaddress. For Frame Relay VCs this is in
E.164 and f…
OctetStringr/w
Constraints:
range: 0-40
 .1.3.6.1.4.1.2076.27.1.6.1.5
ifWanSustainedSpeed deprecated
The sustained or minimum gauranteed speed of
the interface. This is semantically similar to
the CIR for FR and SCR for ATM. The value to be
assigned is the CIR or SCR as the case may be.
This value is used by IP-QoS.
…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.2076.27.1.6.1.6
ifWanPeakSpeed deprecated
The maximum speed available on the interface.
This is semantically similar to the CIR+EIR for FR
and PCR for ATM. This value is used by IP-QoS.

For PPP links this object should be given the value
of the …
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.2076.27.1.6.1.7
ifWanMaxBurstSize deprecated
The maximum burst size in bytes that the interface
can sustain. This is semantically similar to the Bc for FR
and MBS for ATM. This value is used by IP-QoS.

For PPP links this object should be given the v…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.2076.27.1.6.1.8
ifWanIpQosProfileIndex deprecated
The index of an IP-QoS profile which is configured
in the IP-QoS MIB. Assigning the index of the profile
results in instantiation of that profile for the
interface.

This object is optional and may be spe…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.2076.27.1.6.1.9
ifWanIdleTimeout deprecated
The minimum duration (in seconds) to wait before
disconnecting an idle established circuit/interface. (a
default value of 0 where not required) Specification
of the object is optional for all interfaces; if not
specifie…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.2076.27.1.6.1.10
ifWanPeerIpAddr deprecated
The IP address of the peer to whom this interface is
established with. Specification of this value is optional
for all interfaces.

For PPP and MLPPP interfaces, this value if specified
is used during IPCP…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.27.1.6.1.11
ifWanRtpHdrComprEnable deprecated
Enable or disable the RTP header compression on the
WAN interface. This object is writable for only those
interface which are registered with IP. If the RTP
header compression negotiation with the peer fails then
this o…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.2076.27.1.6.1.12
ifWanPersistence deprecated
The persistence of the WAN interface in the system.

Demand(2) circuits are pre-configured but are opened only
when there is some data to be sent (these interfaces are
administratively UP, but operationa…
Enumerationr/w
Enumerated Values:
1other
2demand
 .1.3.6.1.4.1.2076.27.1.6.1.13

ifAutoCktProfileTable

table deprecated
.1.3.6.1.4.1.2076.27.1.7 · 1 row entry · 9 columns
Open in standard view 
A list of all the automatic circuit profiles in the system. 
This table contains objects which are useful for configuration
of an automatic circuit profile for a given interface.
The profile specified here is used for the configuration of
all the incoming calls on the specified interface. The new
interfaces are assigned MIB-2 ifIndex upon creation. The
interface is deleted once the circuit is closed.
ifAutoProfileEntry entry .1.3.6.1.4.1.2076.27.1.7.1
An entry containing information applicable
to an automatic circuit profile for an interface.
Indexes
ifAutoProfileIfIndex
Column Syntax OID
ifAutoProfileIfIndex deprecated
The MIB-2 ifIndex of the interface for which
this automatic circuit profile is applicable.
All incoming calls on this interface will be
handled/configured according to this profile.
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.2076.27.1.7.1.1
ifAutoProfileIfType deprecated
The type of the WAN interface. This is
same as if MIB-2 ifType and ifMainType.
Enumeration
Enumerated Values:
5rfc877x25
32frameRelay
49aal5
114ipOverAtm
 .1.3.6.1.4.1.2076.27.1.7.1.2
ifAutoProfileIpAddrAllocMethod deprecated
The mechanism to be used for allocation of IP
address for this interface.

The value negotiation can be used only if PPP
or MLPPP interfaces are to run over the automatic
circuits.

The loca…
Enumerationr/w
Enumerated Values:
1other
2negotiation
3localAddressPool
 .1.3.6.1.4.1.2076.27.1.7.1.3
ifAutoProfileDefIpSubnetMask deprecated
Specifies the default IP Subnet Mask for this
profile. The value should be specified only
for network interfaces and any valid VLSM is
accepted.

If not specified, this object takes the default
subnet mas…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.27.1.7.1.4
ifAutoProfileDefIpBroadcastAddr deprecated
Specifies the default IP broadcast address for this
interface. Any valid broadcast
address based on a valid VLSM is accepted.

If not specified, this object takes the default
value based on the class of t…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.27.1.7.1.5
ifAutoProfileIdleTimeout deprecated
The minimum duration (in seconds) to wait before
disconnecting an idle automatic circuit. Specification
of the object is mandatory.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.2076.27.1.7.1.6
ifAutoProfileEncapType deprecated
The encapsulation type to be used over the automatic
circuit.

For FR interface, the value can be nlpid(2) (for carrying protocols
which have NLPID) or nlpidSnap(3) (for other protocols). The
default is n…
Enumerationr/w
Enumerated Values:
1other
2nlpid
3nlpidSnap
4cudNlpid
5cudNlpidSnap
6llcSnap
7vcMultiplexed
 .1.3.6.1.4.1.2076.27.1.7.1.7
ifAutoProfileIpQosProfileIndex deprecated
The index of an IP-QoS profile which is configured
in the IP-QoS MIB. Assigning the index of the profile
results in instantiation of that profile for any
automatic circuit which is instantiated based on this
profile (an…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.2076.27.1.7.1.8
ifAutoProfileRowStatus deprecated
A RowStatus object for creation of automatic circuit
profile on a per interface basis.

It is necessary to create the parent FR,X.25 or ATM/IPoA
interface before creating the automatic circuit profile
for …
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.2076.27.1.7.1.9

ifIvrTable

table
.1.3.6.1.4.1.2076.27.1.8 · 1 row entry · 1 columns
Open in standard view 
A list of all the interfaces in the system with IVR related
configurations.
          
This table is an extension to the ifMainTable. The index to 
this table has the semantics of the ifMainIndex of the 
ifMainTable.
ifIvrEntry entry .1.3.6.1.4.1.2076.27.1.8.1
An entry containing IVR-related information applicable
to a interface.
Indexes
ifMainIndex
Column Syntax OID
ifIvrBridgedIface
Indicates if this interface is a Bridged interface
or not.
A value of 'TRUE' indicates that this interface is
a Bridged interface and is capable of performing
bridging of packets through this interface.
A value of 'F…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.2076.27.1.8.1.1

ifSecondaryIpAddressTable

table
.1.3.6.1.4.1.2076.27.1.11 · 1 row entry · 4 columns
Open in standard view 
A list of secondary IP addresses configured over the 
interfaces registered with IP.
                
This table is a extension to the ifMainTable. 
The index to this table has the semantics of
the ifMainIndex of the ifMainTable.
          
Secondary IpAddress configuration should not override the 
primary ip address configured for any of the interface
          
Updation of entries in this table are not allowd when 
RowStatus is active
ifSecondaryIpAddressEntry entry .1.3.6.1.4.1.2076.27.1.11.1
An entry contains the information associated with the
secondary(additional) ip address configured to a particular
interface.
Indexes
ifMainIndex ifSecondaryIpAddress
Column Syntax OID
ifSecondaryIpAddress
Specifies the Secondary IP address associated with the
interface
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.27.1.11.1.1
ifSecondaryIpSubnetMask
Specifies the IP Subnet Mask associted with the
secondary ip address configuration. The value should be
specified only for network interfaces and any valid
VLSM is accepted.

If not specified, this obje…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.27.1.11.1.2
ifSecondaryIpBroadcastAddr
Specifies the IP broadcast address associated with
the configured secondary IP address. The value should be
specified only for network interfaces and any valid
broadcast address based on a valid VLSM is accepted.
…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.27.1.11.1.3
ifSecondaryIpRowStatus
This object is used to manage creation and deletion of rows
in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.2076.27.1.11.1.4

ifMainExtTable

table
.1.3.6.1.4.1.2076.27.1.12 · 1 row entry · 8 columns
Open in standard view 
This table is an extension to the ifMainTable.
ifMainExtEntry entry .1.3.6.1.4.1.2076.27.1.12.1
An entry containing additional management information
applicable to a particular interface.
Indexes
No indexes recorded
Column Syntax OID
ifMainExtMacAddress
The unicast MacAddress for each interface.
The Macaddress can be set only when ifMainAdminStatus for the
interface is down(2). The object is valid only for
interfaces that have the ifMainType set as ethernetCsmacd(6) …
SNMPv2-TCMacAddressr/w
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.2076.27.1.12.1.8
ifMainExtSysSpecificPortID
System specific index configured for the port.
It provides a different numbering space other than the
IfIndex to identify ports.
Valid range for this object is from 1 to 16384.
The value 0 is not allowed to be set. O…
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.1.12.1.9
ifMainExtInterfaceType
This object reflects the usage of this interface, whether it is a
frontpanel interface or a backplane interface used for interswitching
in distributed environments.

frontpanelport -
The interface behave…
Enumerationr/w
Enumerated Values:
1frontpanelport
2backplaneport
 .1.3.6.1.4.1.2076.27.1.12.1.10
ifMainExtPortSecState
The interface port security state says whether the port is connected
to trusted hosts or not. If a port is trusted, the packets coming
on that ports will also be trusted. By default all the ports will be
untrusted. If t…
Enumerationr/w
Enumerated Values:
0untrusted
1trusted
 .1.3.6.1.4.1.2076.27.1.12.1.11
ifMainExtInPkts
Total number of packets received on this interface. This includes the
total of Unicast, Multicast and Broadcast packets received on a interface.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.1.12.1.12
ifMainExtLinkUpEnabledStatus
This enables or disables Link Up Delay functionality in this port.
A value of 'enabled'(1) indicates that, operational status of the
link is suspended for a configured delay time 'ifMainExtLinkUpDelayTimer'.
A value…
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.2076.27.1.12.1.13
ifMainExtLinkUpDelayTimer
This configures the delay timer for the link up enabled interface.
It takes the timer value (in seconds) minimum value as 1 and
maximum value as 1000.
secondsSNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.1.12.1.14
ifMainExtLinkUpRemainingTime
This object is for displaying the pending time left
for the link Operation Status to be made UP.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.1.12.1.15

ifCustTLVTable

table
.1.3.6.1.4.1.2076.27.1.13 · 1 row entry · 4 columns
Open in standard view 
This table allows generic TLV data to be configured per-port.
It may be used to store any port-specific information that 
is required by any application.
ifCustTLVEntry entry .1.3.6.1.4.1.2076.27.1.13.1
Entry about the TLV information
Indexes
ifMainIndex ifCustTLVType
Column Syntax OID
ifCustTLVType
Type of the TLV Information.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.1.13.1.1
ifCustTLVLength
Length of the TLV Information.
Specification of this object is mandatory for ifCustTLVRowStatus to
be made active. Length should be configured after the row creation in
ifCustTLVTable and before configuring the ifCust…
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.1.13.1.2
ifCustTLVValue
Value of the TLV Information. The default value is 0.
SNMPv2-TCDisplayStringr/w
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.2076.27.1.13.1.3
ifCustTLVRowStatus
RowStatus of the Corresponding Entry.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.2076.27.1.13.1.4

ifCustOpaqueAttrTable

table
.1.3.6.1.4.1.2076.27.1.14 · 1 row entry · 3 columns
Open in standard view 
This table allows generic integer attributes to be configured 
per-port. These attributes will be opaque from ISS's point of 
view and will not be processed/understood by ISS.
ifCustOpaqueAttrEntry entry .1.3.6.1.4.1.2076.27.1.14.1
Entry for every opaque attribute on each port.
Indexes
ifMainIndex ifCustOpaqueAttributeID
Column Syntax OID
ifCustOpaqueAttributeID
OpaqueAttribute ID configured on the port. Four opaque attributes are
supported on each port
Enumeration
Enumerated Values:
1opaqueAttr1
2opaqueAttr2
3opaqueAttr3
4opaqueAttr4
 .1.3.6.1.4.1.2076.27.1.14.1.1
ifCustOpaqueAttribute
Value for the Opaque attribute.This value can be altered when
ifCustOpaqueRowStatus is ACTIVE.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.1.14.1.2
ifCustOpaqueRowStatus
RowStatus of the Corresponding Entry. NOT_IN_SERVICE value is not
supported.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.2076.27.1.14.1.3

ifBridgeILanIfTable

table
.1.3.6.1.4.1.2076.27.1.15 · 1 row entry · 1 columns
Open in standard view 
This table is used to read the status of an I-Lan interface
created from Iftable. An I-LAN Interface is
 used to create internal connections between bridge ports in a
 802.1 device.  An I-LAN Interfaces can be directly associated
 with a set of bridge ports.  An I-LAN Interfaces can also be
 used as a stacking interface to relate other interfaces before
 association to bridge ports.
          
 For example, an I-LAN interface can be created to link traffic
 between a PIP and a CBP.  This involves creation of an interface
 of type iLan with a corresponding entry made in the ifTable. 
           
 The IfIndex corresponding to the ILAN is put in the IlanifTable.
 A CBP is created in a B Component of IfType internal and  CBP 
 related IfEntry is stacked upon the IfEntry of the I-LAN using 
 the IfStackTable.  Similarly, a PIP is created in a I Component
 of IfType internal and  PIP related IfEntry is stacked upon the
 IfEntry of the I-LAN using the IfStackTable. 
 Finally, a VIP is created with ifType internal on the I-Component
 and is associated with the PIP, thus completing the path from 
 the I-Component's MAC relay to the CBP on the B-Component.
          
 Entries in this table must be persistent over power up
 restart/reboot.
ifBridgeILanIfEntry entry .1.3.6.1.4.1.2076.27.1.15.1
Each entry consists of a Status to get the I-Lan interface status
Indexes
IF-MIBifIndex
Column Syntax OID
ifBridgeILanIfStatus
This object is used to read the status of an I-Lan interface
created from Iftable.
Enumeration
Enumerated Values:
1active
2outOfService
 .1.3.6.1.4.1.2076.27.1.15.1.1

ifTypeProtoDenyTable

table
.1.3.6.1.4.1.2076.27.1.16 · 1 row entry · 5 columns
Open in standard view 
A table to configure the interface types and bridge port types accessible 
to various protocol(s). This table will indicate whether
a particular type of interface is to be created or be visible
in the given protocol module. An entry in this table will cause the 
particular type of interface to be denied from being accessed by the 
protocol i.e. the particular type of interface will not be created
(i.e. visible) in the given protocol.
ifTypeProtoDenyEntry entry .1.3.6.1.4.1.2076.27.1.16.1
Each entry in this table will give the interface type and bridge port type
that will not be accessible to the protocol for the mentioned context.
Only valid and allowed combinations of ifTypeProtoDenyMainType and
ifTyp…
Indexes
ifTypeProtoDenyContextId ifTypeProtoDenyMainType ifTypeProtoDenyBrgPortType ifTypeProtoDenyProtocol
Column Syntax OID
ifTypeProtoDenyContextId
Identifies a virtual context in which to deny access of the given interface
type and bridge port type to a protocol.
Unsigned32
Constraints:
range: 0-255
 .1.3.6.1.4.1.2076.27.1.16.1.1
ifTypeProtoDenyMainType
This object type refers to the ifMainType.
The interface types that are currently supported by this table are
ethernetCsmacd(6), propVirtual(53), ieee8023ad(161), brgPort(209) and
pip(248).
Enumeration
Enumerated Values:
6ethernetCsmacd
53propVirtual
161ieee8023ad
209brgPort
248pip
 .1.3.6.1.4.1.2076.27.1.16.1.2
ifTypeProtoDenyBrgPortType
This object type refers to ifMainBrgPortType.
Enumeration
Enumerated Values:
1providerNetworkPort
2customerNetworkPortPortBased
3customerNetworkPortStagged
4customerEdgePort
5propCustomerEdgePort
6propCustomerNetworkPort
7propProviderNetworkPort
8customerBridgePort
9customerNetworkPortCtagged
10virtualInstancePort
11providerInstancePort
12customerBackbonePort
 .1.3.6.1.4.1.2076.27.1.16.1.3
ifTypeProtoDenyProtocol
Identifies the protocol for which the corresponding interface type and
bridge port type will not be accessible/visible.
Enumeration
Enumerated Values:
1pnac
2la
3xstp
4vlan
5garp
6mrp
7pbb
8ecfm
9elmi
10snoop
11lldp
12bridge
13qos
 .1.3.6.1.4.1.2076.27.1.16.1.4
ifTypeProtoDenyRowStatus
Indicates the status of the row. Valid values are 'createAndGo' and
'destroy'. A row can be created in this table by assigning the value
'createAndGo' for the status object which will cause the entry to become
active.…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.2076.27.1.16.1.5

ifIvrMappingTable

table
.1.3.6.1.4.1.2076.27.1.18 · 1 row entry · 2 columns
Open in standard view 
This table is used to configure the list of vlans to be 
associated for an IVR interface.
The primary Index to this table can only be a IVR interface.
ifIvrMappingEntry entry .1.3.6.1.4.1.2076.27.1.18.1
Each entry in this table gives an assoicated vlan to an IVR
interface.
Indexes
ifMainIndex ifIvrAssociatedVlan
Column Syntax OID
ifIvrAssociatedVlan
This object specifies one of the associated VLANs for a given
IVR interface. Vlan Id associated with an IVR interface during
IVR interface creation, should not be configured as
ifIvrAssociatedVlan for that IVR interfac…
Q-BRIDGE-MIBVlanId
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.2076.27.1.18.1.1
ifIvrMappingRowStatus
Denotes the Row Status for port isolation table entry.
Only 'CreateAndGo' and 'destroy' values are allowed for this
object. 'CreateAndWait' and 'notInService' values are not allowed.
Example:
To add vlans 2, 3 as ass…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.2076.27.1.18.1.2

ifHCErrorTable

table
.1.3.6.1.4.1.2076.27.1.19 · 1 row entry · 5 columns
Open in standard view 
A list of interface entries.  The number of entries is
given by the value of ifNumber.  This table contains
additional objects for the interface table.
ifHCErrorEntry entry .1.3.6.1.4.1.2076.27.1.19.1
An entry containing additional management information
applicable to a particular interface.
Indexes
No indexes recorded
Column Syntax OID
ifHCInDiscards
The number of inbound packets which were chosen to be
discarded even though no errors had been detected to prevent
their being deliverable to a higher-layer protocol. One
possible reason for discarding such a packet co…
SNMPv2-SMICounter64
Textual Convention: SNMPv2-SMICounter64 Unsigned64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2076.27.1.19.1.1
ifHCInErrors
For packet-oriented interfaces, the number of inbound
packets that contained errors preventing them from being
deliverable to a higher-layer protocol. For character-
oriented or fixed-length interfaces, the number of i…
SNMPv2-SMICounter64
Textual Convention: SNMPv2-SMICounter64 Unsigned64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2076.27.1.19.1.2
ifHCInUnknownProtos
For packet-oriented interfaces, the number of packets
received via the interface which were discarded because of
an unknown or unsupported protocol. For character-oriented
or fixed-length interfaces that support protoc…
SNMPv2-SMICounter64
Textual Convention: SNMPv2-SMICounter64 Unsigned64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2076.27.1.19.1.3
ifHCOutDiscards
The number of outbound packets which were chosen to be
discarded even though no errors had been detected to prevent
their being transmitted. One possible reason for discarding
such a packet could be to free up buffer s…
SNMPv2-SMICounter64
Textual Convention: SNMPv2-SMICounter64 Unsigned64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2076.27.1.19.1.4
ifHCOutErrors
For packet-oriented interfaces, the number of outbound
packets that could not be transmitted because of errors.
For character-oriented or fixed-length interfaces, the
number of outbound transmission units that could not…
SNMPv2-SMICounter64
Textual Convention: SNMPv2-SMICounter64 Unsigned64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2076.27.1.19.1.5

ifAvailableIndexTable

table
.1.3.6.1.4.1.2076.27.1.24 · 1 row entry · 1 columns
Open in standard view 
This table returns the next available free interface
index for the given interface type
ifAvailableIndexEntry entry .1.3.6.1.4.1.2076.27.1.24.1
This is an entry in the ifAvailableFreeIndex Table
Indexes
IF-MIBifType
Column Syntax OID
ifAvailableFreeIndex
This is the next available free interfac index for a given ifType
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.2076.27.1.24.1.1

ifACTable

table
.1.3.6.1.4.1.2076.27.1.25 · 1 row entry · 2 columns
Open in standard view 
A list of Attachment Circuit interface related
configurations. Attachment Circuit is a virtual interface
that is a  combination of physical port and customer vlan
identifier or it is a virtual interface that contains
underlying physical port alone.
          
This table is an extension to the ifMainTable. The index to
this table has the semantics of the ifMainIndex of the
ifMainTable.
ifACEntry entry .1.3.6.1.4.1.2076.27.1.25.1
An entry containing AC-related information applicable
to attachment cirucit interface only.
Indexes
ifMainIndex
Column Syntax OID
ifACPortIdentifier
This is the physical interface on which the attachment
circuit interface is present. The operational status of the
attachment circuit interface depends on this port's operational
status. That is if the operational statu…
IF-MIBInterfaceIndexr/w
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.2076.27.1.25.1.1
ifACCustomerVlan
This is the customer vlan present for the attachment circuit
interface. This object alone can not determine the attachment
circuit interface. To determine that, this object should be together
present with the ifACPortId…
Q-BRIDGE-MIBVlanIdr/w
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.2076.27.1.25.1.2

ifUfdGroupTable

table
.1.3.6.1.4.1.2076.27.1.30 · 1 row entry · 9 columns
Open in standard view 
This table contains a list of all the Uplink Failure Detection
(UFD).  Group entries in the system.
          
This table is a extension to the ifMainTable. The index to this 
table is the group id. Entries are created when the group id is 
created in this table.
ifUfdGroupEntry entry .1.3.6.1.4.1.2076.27.1.30.1
An entry containing group information with
uplink/downlink port count and status of the group.
Indexes
ifUfdGroupId
Column Syntax OID
ifUfdGroupId
An identifier that uniquely identifies the
group Entry in this table.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.2076.27.1.30.1.1
ifUfdGroupName
This object is used to identity the Uplink Failure Detection
(UFD) Group-name.
OctetStringr/w
Constraints:
range: 1-32
 .1.3.6.1.4.1.2076.27.1.30.1.2
ifUfdGroupStatus
This object for indicating the status of the group.
The group status can be set 'up' only when any one uplink
port is in admin and operationally 'UP' state in the group.
The group status can be set 'down' only when al…
Enumeration
Enumerated Values:
1up
2down
 .1.3.6.1.4.1.2076.27.1.30.1.3
ifUfdGroupUplinkPorts
Specifies the complete set of uplink ports which are mapped with
group
Q-BRIDGE-MIBPortListr/w
Textual Convention: Q-BRIDGE-MIBPortList OctetString
 .1.3.6.1.4.1.2076.27.1.30.1.4
ifUfdGroupDownlinkPorts
Specifies the complete set of downlink ports which are mapped
with group
Q-BRIDGE-MIBPortListr/w
Textual Convention: Q-BRIDGE-MIBPortList OctetString
 .1.3.6.1.4.1.2076.27.1.30.1.5
ifUfdGroupDesigUplinkPort deprecated
A port is termed as designated uplink when the port is connected
to the network and it has more preference to a particular set of
uplink ports.

Broadcast/unknown multicast will use this designated port to…
IF-MIBInterfaceIndexr/w
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.2076.27.1.30.1.6
ifUfdGroupUplinkCount
A counter which indicates the number of
Uplink ports within the group
Integer32
Constraints:
range: 1-48
 .1.3.6.1.4.1.2076.27.1.30.1.7
ifUfdGroupDownlinkCount
A counter which indicates the number of
Downlink ports within the group
Integer32
Constraints:
range: 1-48
 .1.3.6.1.4.1.2076.27.1.30.1.8
ifUfdGroupRowStatus
This object is used to manage creation and deletion of rows
in this Uplink Failure Detection(UFD) group table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.2076.27.1.30.1.9

ifVlanIpTable

table
.1.3.6.1.4.1.2076.27.1.36 · 1 row entry · 7 columns
Open in standard view 
This table contains L3 interface attributes 
that are used for manipulating entries in 
various tables. 
          
ifVlanIpTable entry creation, modification and 
deletion results in related actions being 
performed for the ifMainTable and the ifIpTable. 
Likewise, data returned through ifVlanIpTable 
table queries is derived from these tables.
ifVlanIpEntry entry .1.3.6.1.4.1.2076.27.1.36.1
Information about the L3 interface settings
for a specific VLAN on the device.
Indexes
ifVlanIpVlanId
Column Syntax OID
ifVlanIpVlanId
VLAN ID for the L3 interface specification.
Q-BRIDGE-MIBVlanId
Textual Convention: Q-BRIDGE-MIBVlanId Integer32
Type Constraints:
range: 1..4094
 .1.3.6.1.4.1.2076.27.1.36.1.1
ifVlanIpIfIndex
The ifIndex associated with the VLAN ID for
this L3 interface specification. An ifIndex
is automatically allocated when a new entry
is created. The ifIndex and related settings
are automatically deleted when an entry is…
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.2076.27.1.36.1.2
ifVlanIpAdminStatus
The desired state of the interface. This
attribute has similar semantics to the
ifAdminStatus object of the standard ifTable.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.2076.27.1.36.1.3
ifVlanIpAddrAllocMethod
The mechanism to be used for allocation of
the IPv4 address for this L3 VLAN interface.
Enumerationr/w
Enumerated Values:
1manual
2dynamic
 .1.3.6.1.4.1.2076.27.1.36.1.4
ifVlanIpAddr
Specifies the IPv4 address assigned to
this L3 VLAN interface.

A valid IpAddress value is required when
creating a new entry and the associated
address allocation method is 'manual'. A
zero IpAddress va…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.27.1.36.1.5
ifVlanIpSubnetMask
Specifies the IPv4 address subnet mask
assigned to this L3 VLAN interface.

A valid subnet mask value is required when
creating a new entry and the associated
address allocation method is 'manual'. A
zero…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.27.1.36.1.6
ifVlanIpRowStatus
This object allows entries to be created, modified
and deleted in the ifVlanIpTable. Values 'createAndWait',
'active' and 'destroy' are supported for Sets.

The rowStatus value of the underlying ifMainEnt…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.2076.27.1.36.1.10

ffHostCacheTable

table deprecated
.1.3.6.1.4.1.2076.27.2.11 · 1 row entry · 8 columns
Open in standard view 
This table has entries corresponding to the current 
entries in the Host Cache. The entries in this table
can be added, deleted or modified.
ffHostCacheEntry entry .1.3.6.1.4.1.2076.27.2.11.1
An Entry consisting of all the information
about an entry in the Host Cache.
Indexes
ffHostCacheDestAddr
Column Syntax OID
ffHostCacheDestAddr deprecated
The IP address of the destination host.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.27.2.11.1.1
ffHostCacheNextHopAddr deprecated
The IP address of the next-hop to which a packet
for this host are forwarded. This could be same as
ffHostCacheDestAddr if the next-hop is the end-host
as well.

When creating a static entry, this o…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.2076.27.2.11.1.2
ffHostCacheIfIndex deprecated
Identifies the MIB-2 ifIndex of the outgoing
interface over which packets to this host are sent.
When creating a static entry, this object should be
set with the ifIndex of our network interface
for reaching the specif…
IF-MIBInterfaceIndexr/w
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.2076.27.2.11.1.3
ffHostCacheNextHopMediaAddr deprecated
Provides the media address of the next-hop
to which the packet for this host is to be sent to.

It is mandatory to specify the next-hop IP address
and the outgoing ifIndex using the
ffHostCacheNextHopAddr…
OctetStringr/w
Constraints:
range: 0-6
 .1.3.6.1.4.1.2076.27.2.11.1.4
ffHostCacheHits deprecated
Indicates the total number of packets fast-
forwarded to this host.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.2.11.1.5
ffHostCacheLastHitTime deprecated
Indicates the SysUpTime when the last packet
was fast-forwarded to this host.
SNMPv2-TCTimeStamp
Textual Convention: SNMPv2-TCTimeStamp Unsigned32
 .1.3.6.1.4.1.2076.27.2.11.1.6
ffHostCacheEntryType deprecated
An object, which indicates the type of this Host Cache
entry.

A static entry is an entry created by the Network
Manager and is not purged by the system. Such entries
would be invalidated due to rout…
Enumerationr/w
Enumerated Values:
1static
2dynamic
 .1.3.6.1.4.1.2076.27.2.11.1.7
ffHostCacheRowStatus deprecated
A RowStatus object for addition/deletion of Host
Cache entries. It also indicates the status of the
entry.

Set action is not allowed for notInService(2). An entry,
which has become invalid due to a ro…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.2076.27.2.11.1.8

fsPacketAnalyserTable

table
.1.3.6.1.4.1.2076.27.5.1 · 1 row entry · 9 columns
Open in standard view 
This table is used by the Packet Analyser for 
Pattern matching on particular ports
fsPacketAnalyserEntry entry .1.3.6.1.4.1.2076.27.5.1.1
An entry containing Pattern matching information
used by the Packet analyser
Indexes
fsPacketAnalyserIndex
Column Syntax OID
fsPacketAnalyserIndex
An arbitrary integer value, greater than zero,
which uniquely identifies a pattern to be matched
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.5.1.1.1
fsPacketAnalyserWatchValue
This represents the pattern which is to be matched
in the packet to be analysed by the packet analyser
OctetStringr/w
Constraints:
range: 0-1600
 .1.3.6.1.4.1.2076.27.5.1.1.2
fsPacketAnalyserWatchMask
The mask for the pattern to be matched by the packet analyser
OctetStringr/w
Constraints:
range: 0-1600
 .1.3.6.1.4.1.2076.27.5.1.1.3
fsPacketAnalyserWatchPorts
Specifies the complete set of ports over which the pattern is
to be matched by the packet analyser
Q-BRIDGE-MIBPortListr/w
Textual Convention: Q-BRIDGE-MIBPortList OctetString
 .1.3.6.1.4.1.2076.27.5.1.1.4
fsPacketAnalyserMatchPorts
Specifies the complete set of ports over which the pattern is
matched by the packet analyser
Q-BRIDGE-MIBPortList
Textual Convention: Q-BRIDGE-MIBPortList OctetString
 .1.3.6.1.4.1.2076.27.5.1.1.5
fsPacketAnalyserCounter
Number of times the pattern was matched over the watched ports
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.5.1.1.6
fsPacketAnalyserTime
The value of sysUpTime when the pattern was last matched
SNMPv2-SMITimeTicks
Textual Convention: SNMPv2-SMITimeTicks Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.5.1.1.7
fsPacketAnalyserCreateTime
The value of sysUpTime when the system was initiated
SNMPv2-SMITimeTicks
Textual Convention: SNMPv2-SMITimeTicks Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.5.1.1.8
fsPacketAnalyserStatus
Specifies the Row Status for the entry in this table
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.2076.27.5.1.1.9

fsPacketTransmitterTable

table
.1.3.6.1.4.1.2076.27.5.2 · 1 row entry · 6 columns
Open in standard view 
This table is used by the Packet Transmitter for 
sending the packets on particular ports
fsPacketTransmitterEntry entry .1.3.6.1.4.1.2076.27.5.2.1
An entry containing Packet information
used by the Packet Transmitter
Indexes
fsPacketTransmitterIndex
Column Syntax OID
fsPacketTransmitterIndex
An arbitrary integer value, greater than zero,
which uniquely identifies a packet to be sent
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.5.2.1.1
fsPacketTransmitterValue
This represents the pattern which is to be sent
through the given port by the packet transmitter
OctetStringr/w
Constraints:
range: 0-1600
 .1.3.6.1.4.1.2076.27.5.2.1.2
fsPacketTransmitterPort
Specifies the port over which the packet is to be sent by
the packet transmitter
Q-BRIDGE-MIBPortListr/w
Textual Convention: Q-BRIDGE-MIBPortList OctetString
 .1.3.6.1.4.1.2076.27.5.2.1.3
fsPacketTransmitterInterval
The Time interval for sending the packet over the port in seconds
SNMPv2-SMITimeTicksr/w
Textual Convention: SNMPv2-SMITimeTicks Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.5.2.1.4
fsPacketTransmitterCount
Number of packet to be sent over the ports
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2076.27.5.2.1.5
fsPacketTransmitterStatus
Specifies the Row Status for the entry in this table
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.2076.27.5.2.1.6