A3Com-IPX-r5-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
11
Rows
11
Columns
64

a3ipxControlTable

table mandatory
.1.3.6.1.4.1.43.2.7.1.7.1 · 1 row entry · 5 columns
Open in standard view 
A list of port-specific IPX control parmeters.
This table is used currently to control ipx routing, 
WAN broadcasts, and WAN checksums.
a3ipxControlEntry entry .1.3.6.1.4.1.43.2.7.1.7.1.1
Each entry in this table applies control over
a seperate port.
Indexes
a3ipxControlPort
Column Syntax OID
a3ipxControlPort mandatory
The IPX port to which this entry applies.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.7.1.7.1.1.1
a3ipxControlRoute mandatory
If this object is set to enabled(1), then IPX routing
is enabled. If this object is set to disabled(2),
then IPX routing is disabled. Note, if this is disabled(2),
then RIP is disabled as well (for this Port).
…
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.7.1.7.1.1.2
a3ipxControlWanBcast mandatory
If this object is enabled(1), then the IPX router
makes copies of all received WAN broadcast packets
and forwards them to all ports other than the one
on which that packet was received.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.7.1.7.1.1.3
a3ipxControlChecksum mandatory
If this object is set to enabled(1), Checksum will be
generated and checked on IPX packet over WAN.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.7.1.7.1.1.4
a3ipxControlWanOpt mandatory
This object is used to enable or disable the IPX WAN
feature on a specific port. IPX WAN is the protocol
Novell IPX uses to exchange necessary router to
router information prior to exchanging IPX RIP and
SAP informati…
Enumerationr/w
Enumerated Values:
1wan
2noWan
 .1.3.6.1.4.1.43.2.7.1.7.1.1.5

a3ipxRipControlTable

table mandatory
.1.3.6.1.4.1.43.2.7.2 · 1 row entry · 14 columns
Open in standard view 
A list of RIP Control parameter entries
a3ipxRipControlEntry entry .1.3.6.1.4.1.43.2.7.2.1
A list of parameters that determin how IPX updates
its routing table.
Indexes
a3ipxRipControlPort
Column Syntax OID
a3ipxRipControlPort mandatory
The IPX port to which this entry applies.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.7.2.1.1
a3ipxRipControlSwitch obsolete
If this object is set to enabled(1), IPX RIP exchanges
RIP information with its neighbors and maintains the
routing table dynamically. If this object is set to
disabled(2), dynamic learning is stopped and no
RIP updat…
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.7.2.1.2
a3ipxRipControlTrigger mandatory
If this object is set to enabled(1), triggered
responses are sent when the network topology changes,
allowing the network to calculate potentially better
routes. If this object is disabled(2), topology
change responses…
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.7.2.1.3
a3ipxRipControlPoison mandatory
If this object is set to enabled(1), Split Horizon with
Poison Reverse is performed. If this object is set to
disabled(2), the router omits routes learned from one
neighbor in regular updates sent to that neighbor.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.7.2.1.4
a3ipxRipControlMapOpt mandatory
X.25 addresses and Frame Relay DLCIs can be mapped in
two different ways: by using IPX network numbers
as previously implemented (OldNbrMap) or by using the
Ethernet address of the remote NETBuilder currently
implement…
Enumerationr/w
Enumerated Values:
1oldNbrMap
2newNbrMap
 .1.3.6.1.4.1.43.2.7.2.1.5
a3ipxRipControlWanOpt obsolete
This object is used to enable or disable the IPX WAN
feature on a specific port. IPX WAN is the protocol
Novell IPX uses to exchange necessary router to
router information prior to exchanging IPX RIP and
SAP informati…
Enumerationr/w
Enumerated Values:
1wan
2noWan
 .1.3.6.1.4.1.43.2.7.2.1.6
a3ipxRipControlPerRip mandatory
This object is used to specify how this router
generates IPX RIP updates. If this object is set
to periodicRip(1), the router will generate RIP
updates periodically. If this object is set to
nonPeriodicRip(2), the rou…
Enumerationr/w
Enumerated Values:
1periodicRip
2nonPeriodicRip
 .1.3.6.1.4.1.43.2.7.2.1.7
a3ipxRipControlPerSap mandatory
This object is used to specify how this router
generates IPX SAP updates. If this object is set
to periodicSap(1), the router will generate SAP
updates periodically. If this object is set to
nonPeriodicSap(2), the rou…
Enumerationr/w
Enumerated Values:
1periodicSap
2nonPeriodicSap
 .1.3.6.1.4.1.43.2.7.2.1.8
a3ipxRipControlTalk obsolete
This object controls the transmission of IPX RIP
updates on this port. If enabled, IPX RIP updates
are sent. If disabled, they are not sent.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.7.2.1.9
a3ipxRipControlListen obsolete
This object determines if IPX RIP updates are accepted
over this port. If this object is enabled(1), then the
IPX router listens to the incoming RIP updates.
If this object is set to disabled(2), then the IPX
router d…
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.7.2.1.10
a3ipxSapControlTalk obsolete
This object controls the transmission of IPX SAP
updates on this port. If enabled, IPX SAP updates
are sent. If disabled, they are not sent.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.7.2.1.11
a3ipxSapControlListen obsolete
This object determines if IPX SAP updates are accepted
over this port. If this object is enabled(1), then the
IPX router listens to the incoming SAP updates.
If this object is set to disabled(2), then the IPX
router d…
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.7.2.1.12
a3ipxRipCtl mandatory Enumerationr/w
Enumerated Values:
1talkListen
2talkNoListen
3noTalkListen
4noTalkNoListen
5auto
 .1.3.6.1.4.1.43.2.7.2.1.13
a3ipxSapCtl mandatory Enumerationr/w
Enumerated Values:
1talkListen
2talkNoListen
3noTalkListen
4noTalkNoListen
5auto
 .1.3.6.1.4.1.43.2.7.2.1.14

a3ipxWaAddrTable

table mandatory
.1.3.6.1.4.1.43.2.7.3 · 1 row entry · 5 columns
Open in standard view 
A list of IPX entities reachable across a
wide area network.
a3ipxWaAddrEntry entry .1.3.6.1.4.1.43.2.7.3.1
Each entry contains the WAN Address of an IPX
entity. Each entry also contains the IPX port
over which the entity can be reached.
Indexes
a3ipxWaAddrEthAddress
Column Syntax OID
a3ipxWaAddrEthAddress mandatory
The Ethernet address (IPX Node ID) of a remote IPX entity.
.1.3.6.1.4.1.43.2.7.3.1.1
a3ipxWaAddrPort mandatory
The IPX port through which the IPX entity identified
by a3ipxWaAddrEthAddress can be reached.
Integer32r/w
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.7.3.1.2
a3ipxWaAddrDLType mandatory
The type of address that is returned by
a3ipxWaAddrDLAddress.
Enumerationr/w
Enumerated Values:
1x25
2frameRelay
3smds
 .1.3.6.1.4.1.43.2.7.3.1.3
a3ipxWaAddrDLAddress mandatory
The WAN address that is used to reach the IPX entity
corresponding to this table entry.
RFC1213-MIBPhysAddressr/w
Textual Convention: RFC1213-MIBPhysAddress OctetString
 .1.3.6.1.4.1.43.2.7.3.1.4
a3ipxWaAddrStatus mandatory
This object is used to add and delete entries
in this table. See the notes describing
RowStatus at the beginning of this MIB.
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.7.3.1.5

a3ipxAttachedNetTable

table mandatory
.1.3.6.1.4.1.43.2.7.4 · 1 row entry · 6 columns
Open in standard view 
A list of the IPX Network Numbers attached to an IPX port.
a3ipxAttachedNetEntry entry .1.3.6.1.4.1.43.2.7.4.1
Each entry specifies an IPX network number, assigns
it to a port, and specifies the header format to
be used when sending IPX packets to that network.
On Ethernet ports, up to four different IPX Network
Numbers may be s…
Indexes
a3ipxAttachedNetNumber
Column Syntax OID
a3ipxAttachedNetNumber mandatory
The IPX Network Number associated with this table entry.
IPXNET
Textual Convention: IPXNET OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.7.4.1.1
a3ipxAttachedNetPort mandatory
The port to which the IPX Network Number is assigned.
Integer32r/w
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.7.4.1.2
a3ipxAttachedNetFormat mandatory
The format of the header used on packets sent to the
IPX Network Number associated with this table entry.

This object can be set to 1, 2, 3, or 4 when adding
an entry for a LAN interface. For WAN interfa…
Enumerationr/w
Enumerated Values:
1ethernet
2ieee
3llc
4snap
5ppp
6x25
7fr
8smds
 .1.3.6.1.4.1.43.2.7.4.1.3
a3ipxAttachedNetType mandatory
When more than one IPX Network Number is assigned to a
port, one must be labeled the primary number and the
rest secondary.
Enumerationr/w
Enumerated Values:
1primary
2secondary
 .1.3.6.1.4.1.43.2.7.4.1.4
a3ipxAttachedNetOperState mandatory
This identifies the current operational
state of an attached IPX network.
Enumeration
Enumerated Values:
1up
2down
 .1.3.6.1.4.1.43.2.7.4.1.5
a3ipxAttachedNetStatus mandatory
This object is used to add and delete entries
in this table. See the notes describing
RowStatus at the beginning of this MIB.
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.7.4.1.6

a3ipxRouteTable

table mandatory
.1.3.6.1.4.1.43.2.7.5 · 1 row entry · 9 columns
Open in standard view 
A list of IPX routes
a3ipxRouteEntry entry .1.3.6.1.4.1.43.2.7.5.1
Each entry specifies an IPX route. The destination
of the route is specified by a3ipxRouteDestNet. The
next hop of the route is specified by a3ipxRouteAttachedNet
and a3ipxRouteDLAddress. Note, IPX routing must be
e…
Indexes
a3ipxRouteDestNet a3ipxRouteType
Column Syntax OID
a3ipxRouteDestNet mandatory
The IPX network number of the destination network.
The value 0xfffffffe is used to represent the
default route.
IPXNET
Textual Convention: IPXNET OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.7.5.1.1
a3ipxRouteAttachedNet mandatory
The network number of the directly connected network
through which the router can reach the destination
network.
IPXNETr/w
Textual Convention: IPXNET OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.7.5.1.2
a3ipxRouteDLType mandatory
The type of network to which the closest router is
attached. This value is determined by the value of
a3ipxRouteAttachedNet.
Enumeration
Enumerated Values:
1ethernet
2x25
3frameRelay
4smds
 .1.3.6.1.4.1.43.2.7.5.1.3
a3ipxRouteDLAddress mandatory
The Data Link address of the next hop router through which
the IPX network can be reached. The type of address is
determined by the value of a3ipxRouteDLType.
RFC1213-MIBPhysAddressr/w
Textual Convention: RFC1213-MIBPhysAddress OctetString
 .1.3.6.1.4.1.43.2.7.5.1.4
a3ipxRouteHops mandatory
The number of gateways that a packet has to pass through
before reaching the destination network. The maximum
number of hops is 15.
Integer32r/w
Constraints:
range: 1-15
 .1.3.6.1.4.1.43.2.7.5.1.5
a3ipxRouteType mandatory
The IPX Router allows up to two routes (ie, two separate
next hop routers) to a specific destination network,
only one of which will be the primary route. The
determination of which is primary and which is secondary
is…
Enumeration
Enumerated Values:
1primary
2secondary
 .1.3.6.1.4.1.43.2.7.5.1.6
a3ipxRouteProto mandatory
This object specifies how the entry was made.
Enumeration
Enumerated Values:
1other
2static
3rip
 .1.3.6.1.4.1.43.2.7.5.1.7
a3ipxRouteDelay mandatory
The delay associated with the route.
Integer32r/w
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.7.5.1.8
a3ipxRouteStatus mandatory
This object is used to add and delete entries
in this table. See the notes describing
RowStatus at the beginning of this MIB. Note,
only statically learned routes may be removed
via this object. Dynamically learned r…
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.7.5.1.9

a3ipxServerTable

table mandatory
.1.3.6.1.4.1.43.2.7.6 · 1 row entry · 7 columns
Open in standard view 
A list of servers reachable via this router
a3ipxServerEntry entry .1.3.6.1.4.1.43.2.7.6.1
Each entry specifies the reachability of a server.
The server name is specified by a3ipxServerName. The
service is fully specified by a3ipxServerName, and
a3ipxServerType.
Indexes
a3ipxServerName a3ipxServerType
Column Syntax OID
a3ipxServerName mandatory
The name of the server.
OctetString
Constraints:
range: 0-47
 .1.3.6.1.4.1.43.2.7.6.1.1
a3ipxServerType mandatory
The type of service available on the server.
OctetString
Constraints:
range: 2-2
 .1.3.6.1.4.1.43.2.7.6.1.2
a3ipxServerNet mandatory
The IPX network number on which the server resides.
IPXNETr/w
Textual Convention: IPXNET OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.43.2.7.6.1.3
a3ipxServerDLAddress mandatory
The Mac address of the server.
r/w .1.3.6.1.4.1.43.2.7.6.1.4
a3ipxServerSocket mandatory
The socket number of the service.
OctetStringr/w
Constraints:
range: 2-2
 .1.3.6.1.4.1.43.2.7.6.1.5
a3ipxServerProto mandatory
This object identifies how the entry was
made. If the entry was learned via the
Service Advertisement Protocol, this object will
have the value sap(3). If the entry was entered
statically, this object will have the v…
Enumeration
Enumerated Values:
1other
2static
3sap
 .1.3.6.1.4.1.43.2.7.6.1.6
a3ipxServerStatus mandatory
This table currently does not allow entries to
be added. This object is used to delete entries
from this table. See the notes describing
RowStatus at the beginning of this MIB. Note,
only statically learned service e…
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.7.6.1.7

a3ipxX25configTable

table mandatory
.1.3.6.1.4.1.43.2.7.7 · 1 row entry · 6 columns
Open in standard view 
A list of IPX X25 configuration entries.
a3ipxX25configEntry entry .1.3.6.1.4.1.43.2.7.7.1
Each entry specifies a list of X25 configuration parameters
applying to an IPX port.
Indexes
a3ipxX25configPort
Column Syntax OID
a3ipxX25configPort mandatory
The port number to which this table entry applies.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.7.7.1.1
a3ipxX25configPID mandatory
The protocol ID that is included in all outgoing IPX
packets sent over the X25 port associated with this
table entry.
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.43.2.7.7.1.2
a3ipxX25configQueueSize obsolete
The maximum number of packets that can be queued
for a specific DTE address when the virtual circuit
or the X25 port is congested.

NOTE: this object is no longer supported by NETBuilders
running sw versio…
Integer32r/w
Constraints:
range: 1-128
 .1.3.6.1.4.1.43.2.7.7.1.3
a3ipxX25configVClimit obsolete
The maximum number of virtual circuits that can
be established concurrently for IPX routing.

NOTE: this object is no longer supported by NETBuilders
running sw version 8.0 and greater. The corresponding
…
Integer32r/w
Constraints:
range: 1-63
 .1.3.6.1.4.1.43.2.7.7.1.4
a3ipxX25configVCtimer obsolete
The maximum amount of time, in minutes, that can elapse
when there is no activity on the X25 virtual circuit
before it is cleared. This applies to the first virtual
circuit established for a particular DTE address. IF…
Integer32r/w
Constraints:
range: 1-512
 .1.3.6.1.4.1.43.2.7.7.1.5
a3ipxX25configProfId mandatory
To specify an X.25 profile that will be used
when the virtual circuit is set-up to carry
the IPX traffic. default (0) indicates that
no x25 profile is specified.
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.43.2.7.7.1.6

a3ipxSmdsGroupAddressTable

table mandatory
.1.3.6.1.4.1.43.2.7.8 · 1 row entry · 2 columns
Open in standard view 
A list of SMDS Group Addresses assigned to IPX Ports.
a3ipxSmdsGroupAddressEntry entry .1.3.6.1.4.1.43.2.7.8.1
Each entry specifies the SMDS Group Address assigned
to an IPX port.
Indexes
a3ipxSmdsGaIpxPort
Column Syntax OID
a3ipxSmdsGaIpxPort mandatory
This identifies an IPX port to which the
SMDS Group Address identified by the corresponding
instance of a3ipxSmdsGaAddress is associated.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.7.8.1.1
a3ipxSmdsGaAddress mandatory
This identifies an SMDS Group address that
is used as the IPX multicast address on the
specified SMDS port. If this object has a value
of all zeros, then no SMDS Group address is
defined for this port.
SMDSAddressr/w
Textual Convention: SMDSAddress OctetString
Type Constraints:
range: 8
 .1.3.6.1.4.1.43.2.7.8.1.2

a3ipxPreferredSvrTable

table mandatory
.1.3.6.1.4.1.43.2.7.9 · 1 row entry · 3 columns
Open in standard view 
A list of those IPX servers that are included
in responses to 'Get Nearest Server' requests.
Separate lists are kept for each port.  When
a request is receive over a particular port, this
system will respond with the preferred server
assigned to that port.  If more than one preferred
server has been assigned to a particular port,
each server will be offered in a round robin 
fashion.  That is, if serverA, serverB, and
serverC have been assigned to port 1, serverA will
be offered in response to the first request,
serverB in response to the second request, and
so on.
a3ipxPreferredSvrEntry entry .1.3.6.1.4.1.43.2.7.9.1
Each entry specifies an IPX server that will
be offered when a 'Get Nearest Server' request
in received over a particular port.
Indexes
a3ipxPrefSvrPort a3ipxPrefSvrName
Column Syntax OID
a3ipxPrefSvrPort mandatory
This identifies an IPX port to which the
IPX server identified by the corresponding
instance of a3ipxPrefSvrName is associated.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.7.9.1.1
a3ipxPrefSvrName mandatory
This identifies an IPX server that is offered
in response to 'Get Nearest Server' requests
received over the port identified by a3ipxPrefSvrPort.
If there exists more than one instance of this
object for a particular po…
OctetString
Constraints:
range: 0-47
 .1.3.6.1.4.1.43.2.7.9.1.2
a3ipxPrefSvrStatus mandatory
This object is used to add and remove entries
from this table. See the definition of RowStatus
at the beginning of this mib module for details.
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.7.9.1.3

a3ipxPortconfigTable

table mandatory
.1.3.6.1.4.1.43.2.7.10 · 1 row entry · 5 columns
Open in standard view 
A list of port-specific parmeters.
a3ipxPortconfigEntry entry .1.3.6.1.4.1.43.2.7.10.1
Each entry in this table applies the paramater over
a seperate port.
Indexes
a3ipxPortconfigPort
Column Syntax OID
a3ipxPortconfigPort mandatory
The port number to which this table entry applies.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.7.10.1.1
a3ipxRipUpdateTime mandatory
This parameter specifies how often the router sends
RIP regular updates to exhange routing information.
This parameter is defined in units of seconds.
Integer32r/w
Constraints:
range: 10-65535
 .1.3.6.1.4.1.43.2.7.10.1.2
a3ipxSapUpdateTime mandatory
This parameter specifies how often the router sends
Sap regular updates to exhange and service information.
This parameter is defined in units of
seconds.
Integer32r/w
Constraints:
range: 10-65535
 .1.3.6.1.4.1.43.2.7.10.1.3
a3ipxDefMetricHops mandatory
This parameter specifies the hop value placed in NRIP
advertisements of the default route. If this object
has the value 0, the default route is not advertised.
Integer32r/w
Constraints:
range: 0-15
 .1.3.6.1.4.1.43.2.7.10.1.4
a3ipxDefMetricTicks mandatory
This parameter specifies the number of ticks placed
in NLSP advertisements of the default route.
Integer32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.43.2.7.10.1.5

a3ipxSpoofCtlTable

table mandatory
.1.3.6.1.4.1.43.2.7.11 · 1 row entry · 2 columns
Open in standard view 
A table of spoof controls for all the ports. Each row, 
represented by a3ipxSpoofCtlEntry, contains the various
spoof controls that are applicable to a port.
a3ipxSpoofCtlEntry entry .1.3.6.1.4.1.43.2.7.11.1
Each entry represents the various spoof controls
applicable to a port.
Indexes
a3ipxSpoofCtlPort
Column Syntax OID
a3ipxSpoofCtlPort mandatory
Specifies the port number, used as an index
to a row entry in the table.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.7.11.1.1
a3ipxSpoofCtlWatchdog mandatory
Used to enable(1) or disable(2) the Spoofing of
Watchdog packets.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.7.11.1.2