wwpLeosEtherPortIngressCosPolicy
WWP-LEOS-PORT-MIB ·
.1.3.6.1.4.1.6141.2.60.2.1.1.1.1.23
Object
column
r/w
Enumeration
This object specifies the ingress cos policy to be applied to all frames coming in on the given port.
Context
- MIB
- WWP-LEOS-PORT-MIB
- OID
.1.3.6.1.4.1.6141.2.60.2.1.1.1.1.23- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- wwpLeosEtherPortEntry
- Table
- wwpLeosEtherPortTable
- Siblings
- 61
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | leave |
2 | fixed |
3 | ippInherit |
4 | phbgInherit |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| wwpLeosEtherPortId Port ID for the instance. Port ID's start at 1,
and may not be consecutive for each additional port.
This port Id should refer to the dot1dBasePort in the
Dot1dBasePortEntry. | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.1 |
| wwpLeosEtherPortOperSpeed deprecated The current operational speed of the port. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.10 |
| wwpLeosEtherPortAdminDuplex The desired mode for the port. It can be set to either half or
full duplex operation. The default value for this object
depends upon the platform. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.11 |
| wwpLeosEtherPortOperDuplex The current duplex mode of the port. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.12 |
| wwpLeosEtherPortAdminFlowCtrl Configures the ports flow control operation. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.13 |
| wwpLeosEtherPortOperFlowCtrl Shows ports flow control configuration. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.14 |
| wwpLeosEtherIngressPvid The Ingress PVID, the VLAN ID associated with untagged frames ingressing
the port or if tunnel is enabled on this port. The max value for this
object is platform dependent. Refe… | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.15 |
| wwpLeosEtherUntagEgressVlanId All the egress frames whose VLAN id matches the wwpLeosEtherUntagEgressVlanId, will
egress the port as untagged. To egress the frames tagged set
wwpLeosEtherUntagEgressVlanId to… | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.16 |
| wwpLeosEtherPortAcceptableFrameTypes When this is admitOnlyVlanTagged(2) the device will
discard untagged frames or Priority-Tagged frames
received on this port. When admitOnlyUntagged(3) is set,
the device will dis… | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.17 |
| wwpLeosEtherPortUntaggedPriority deprecated The 802.1p packet priority to be assigned to packets ingressing
this port that do not have an 802.1Q VLAN header. This priority
is also assigned to ingress frame if tunnel is en… | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.18 |
| wwpLeosEtherPortMaxFrameSize Setting this object will set the max frame size allowed on a
port. The max frame size can vary from 1522 bytes to 9216 bytes.
Default value is 1526 bytes. | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.19 |
| wwpLeosEtherPortName A textual string containing information about the
port. This string should indicate about the physical
location of the port as well. | column | OctetString | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.2 |
| wwpLeosEtherPortVlanIngressFiltering When this is true(1) the device will discard incoming
frames for VLANs which do not include this Port in its
Member set. When false(2), the port will accept all
incoming frames. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.20 |
| wwpLeosEtherPortAdminAdvertisedFlowCtrl This object specifies the advertised flow control
for given port. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.21 |
| wwpLeosEtherPortVplsPortType This object specifies whether port is in subscriber type,
network facing side or both. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.22 |
| wwpLeosEtherPortIngressFixedDot1dPri The 802.1p packet priority to be assigned to packets ingressing
this port that do not have an 802.1Q VLAN header. This priority
is also assigned to ingress untagged frame if the… | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.24 |
| wwpLeosEtherPortUntagDataVsi This object specifies the virtual switch to be used for this
port if data frame is untagged. If this object is set to 0 then
device will unset this object.
When setting this ob… | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.25 |
| wwpLeosEtherPortOperationalSpeed An estimate of the port's current bandwidth in k-bits per second
for given port. | column | kbps SNMPv2-SMIGauge32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.26 |
| wwpLeosEtherPortUntagCtrlVsi This object specifies the virtual switch to be used for this
port if control frame is untagged. If this object is set to 0 then
device will unset this object.
When setting this… | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.27 |
| wwpLeosEtherPortMirrorPort This object defines whether the port will allow traffic from other ports to
be mirrored to this port.
To allow traffic from other ports to be sent to this port, set this object t… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.28 |
| wwpLeosEtherPortMirrorIngress The value of this object is the port index of a mirror port. The ingress traffic
of this port can be mirrored by setting the destination port's wwpLeosEtherPortMirrorPort
object t… | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.29 |
| wwpLeosEtherPortDesc A textual string containing port description. | column | OctetString | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.3 |
| wwpLeosEtherPortMirrorEgress The value of this object is the port index of a mirror port. The egress traffic
of this port can be mirrored by setting the destination port's wwpLeosEtherPortMirrorPort
object to… | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.30 |
| wwpLeosEtherPortUntagDataVsiType This object specifies the virtual switch instance type associated with this
port. This object defaults to ethernet and specifies if
wwpLeosEtherPortUntagDataVsi belongs to ether… | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.31 |
| wwpLeosEtherPortUntagCtrlVsiType This object specifies the virtual switch instance type associated with this
port. This object defaults to ethernet and specifies if
wwpLeosEtherPortUntagCtrlVsi belongs to ether… | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.32 |
| wwpLeosEtherPortVsIngressFiltering This item is applicable to this port when the port is
added as a per-port member to a virtual switch. If true(1) the device
will discard incoming tagged frames. If false(2) the de… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.33 |
| wwpLeosEtherPortOperAutoNeg The object specifies the operational auto neg state. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.34 |
| wwpLeosEtherPortUpTime The object specifies the port up time in hundredths of a second. | column | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.35 |
| wwpLeosEtherPortUntagDataVid The Ingress Untagged Data Vid, the VLAN ID stamped on untagged frames
ingressing the port or if tunnel is enabled on this port. To disable
tagging of untagged data on ingress writ… | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.36 |
| wwpLeosEtherPortPhyLoopback This object defines whether the phy has been placed in loopback mode,
which causes frames egressing the port to be looped back to the port. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.37 |
| wwpLeosEtherPortVlanIngressFilterStrict This item is applicable to this port when the port is
added as a to a virtual switch. If true(1) the legacy ingress filter behavior
will be enforced at member addition (drop bit w… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.38 |
| wwpLeosEtherPortMacSaDaSwap This object defines whether the MAC SA and DA will be swapped on
frames egressing the port. This only works on a 311V. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.39 |
| wwpLeosEtherPortType The port type for the port. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.4 |
| wwpLeosEtherPortMacSaDaSwapVlan This object defines whether the MAC SA and DA will be swapped on
specific VLAN frames egressing the port. This only works on a 311V. | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.40 |
| wwpLeosEtherPortResolvedCosPolicy The Resolved Cost Policy.
Setting this attribute is not supported in leos version 4 | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.41 |
| wwpLeosEtherPortMode The mode of the port
Setting this attribute is not supported in leos version 4 | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.42 |
| wwpLeosEtherFixedRcos The fixed Resolve Cost value.
Setting this attribute is not supported in leos version 4 | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.43 |
| wwpLeosEtherPortEgressPortQueueMapId The Egress-port-Queue associated with this port.
Setting this attribute is not supported in leos version 4 | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.44 |
| wwpLeosEtherPortResolvedCosMapId RCOS map id for the port.
Setting this attribute is not supported in leos version 4 | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.45 |
| wwpLeosEtherPortResolvedCosRemarkL2 The object specifies whether to remark L2 based on L3. This applies when the
resolved cos policy is either l3-dscp-cos or dot1d-tag1-cos but not when it is
fixed-cos policy. Set… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.46 |
| wwpLeosEtherPortL2TransformMode L2 transform action for port.
Setting this attribute is not supported in leos version 4 | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.47 |
| wwpLeosEtherPortLinkFlapDetection This object defines whether link flap detection will be
enabled on the port. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.48 |
| wwpLeosEtherPortLinkFlapCount This object defines how many link down events are required
to trigger a link flap event. | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.49 |
| wwpLeosEtherPortPhysAddr The ethernet MAC address for the port. This information can also
be achieved via dot1dTpFdbTable | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.5 |
| wwpLeosEtherPortLinkFlapDetectTime This object defines the time in seconds during which link
down events are accumlated to trigger a link flap event. | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.50 |
| wwpLeosEtherPortLinkFlapHoldTime This object defines the time in seconds that a port will
be operationally disabled after a link flap event, before
it is re-enabled. A value of zero causes the port to
remain dis… | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.51 |
| wwpLeosEtherFixedRColor This sets the fixed color to green (default) or yellow.
Setting this attribute is not supported in saos version 4 | column | PortIngressFixedColor | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.52 |
| wwpLeosEtherPortFrameCosMapId Frame COS map id for the port.
Setting this attribute is not supported in leos version 4 | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.53 |
| wwpLeosEtherPortEgressCosPolicy Sets the egress frame cos policy
Setting this attribute is not supported in leos version 4 | column | PortEgressFrameCosPolicy | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.54 |
| wwpLeosEtherPortEgressSpeed An estimate of the port's current egress bandwidth restriction
in k-bits per second for given port. A value of 0 means there
is no active restriction. This attribute n… | column | kbps SNMPv2-SMIGauge32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.55 |
| wwpLeosEtherPortAdaptiveRateSpeed An estimate of the port's current adaptive-rate bandwidth restriction
in k-bits per second for given port. A value of 0 means there is no
active restriction. This attr… | column | kbps SNMPv2-SMIGauge32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.56 |
| wwpLeosEtherPortMirrorEncap This object defines whether the port will encapsulate mirrored
frames by adding a vlan-tag. (Or, in the case where a mirrored
frame is already tagged, by adding a further vlan-tag… | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.57 |
| wwpLeosEtherPortMirrorEncapVid This object defines the VID that will be added to mirrored frames
when the mirroring encapsulation mode is vlan-tag | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.58 |
| wwpLeosEtherPortMirrorEncapTpid This object defines the tpid used in the tag that is added to
mirrored frames, when the mirroring encapsulation mode is vlan-tag | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.59 |
| wwpLeosEtherPortAutoNeg The object sets the port to AUTO NEG MOde and vice versa.
Specific platforms may have requirements of configuring
speed before moving the port to out of AUTO-NEG mode. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.6 |
| wwpLeosEtherPortIfgDecrease This object defines the number of bytes that will be subtracted
from the minimum standard IFG of 12 bytes as defined in IEEE 802.3.
SAOS 6.x only supports a value of 0 or 4. | column | Integer32 | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.60 |
| wwpLeosEtherPortAdvertSpeed This object defines the speed capabilities that will be advertised during the auto-negotiation process. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.61 |
| wwpLeosEtherPortAdvertDuplex This object defines the duplex capabilities that will be advertised during the auto-negotiation process. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.62 |
| wwpLeosEtherPortAdminStatus The desired state of the port. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.7 |
| wwpLeosEtherPortOperStatus The current operational state of Port. | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.8 |
| wwpLeosEtherPortAdminSpeed Desired speed of the port.
Set the port speed to be either 10MB, 100MB, or gig. Set the
port speed to auto to enable automatic port speed detection.
The default value for this o… | column | Enumeration | .1.3.6.1.4.1.6141.2.60.2.1.1.1.1.9 |