wwpLeosPbtTransitTunnelEtypeRemark

WWP-LEOS-PBT-MIB · .1.3.6.1.4.1.6141.2.60.38.1.1.1.6
MIB view Table view

Object

scalar r/w Enumeration 
Setting this object will enable or disable remarking of the EtherType field in the B-Tag
(tunnel) portion of PBT frames that are transiting through the device without PBT encapsulation,
nor decapsulation.  While enabled, applicable PBT transit frames egressing a PBT enhanced port
will have their B-Tag EtherType marked with the value configured as the wwpLeosPbtTunnelTagEtype.

Context

MIB
WWP-LEOS-PBT-MIB
OID
.1.3.6.1.4.1.6141.2.60.38.1.1.1.6
Type
scalar
Access
readwrite
Status
current
Parent
wwpLeosPbtGlobalAttrs
Siblings
9

Syntax

Enumeration

Values & Constraints

Enumerated Values
1enabled
2disabled

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
wwpLeosPbtBridgeMac
This represents the provider mac address to be used as source mac during PBT encapsulation. If this object is not set then it will return default mac derived from chassis mac.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.6141.2.60.38.1.1.1.1
wwpLeosPbtTunnelSwitchOverHoldTime
This object represents the hold time before data traffic on backup tunnel will automatically switchover to primary tunnel.
scalarmilliseconds SNMPv2-SMIUnsigned32.1.3.6.1.4.1.6141.2.60.38.1.1.1.10
wwpLeosPbtServiceTagEType
This represents the etype value to be used in I-Tag (Service tag) section of PBT encapsulation. The I-tag ether type cannot be modified in native mode PBT
scalarOctetString.1.3.6.1.4.1.6141.2.60.38.1.1.1.2
wwpLeosPbtTunnelTagEtype
This represents the etype value to be used in B-Tag section of PBT encapsulation. Valid values are 8100, 9100 & 88a8
scalarOctetString.1.3.6.1.4.1.6141.2.60.38.1.1.1.3
wwpLeosPbtTunnelReversionState
Setting this object will enable or disable automatic tunnel reversion from backup to primary if primary comes back up. Device will wait for wwpLeosPbtTunnelReversionHoldTime befor…
scalarEnumeration.1.3.6.1.4.1.6141.2.60.38.1.1.1.4
wwpLeosPbtTunnelReversionHoldTime
This object represents the hold time before data traffic on the backup tunnel will automatically revert to the primary tunnel.
scalarmilliseconds SNMPv2-SMIUnsigned32.1.3.6.1.4.1.6141.2.60.38.1.1.1.5
wwpLeosPbtAdminMode
This object represents PBT Admin mode. Some platforms support either non-native or native mode.
scalarEnumeration.1.3.6.1.4.1.6141.2.60.38.1.1.1.7
wwpLeosPbtOperMode
This object represents PBT Oper mode. Some platforms support either non-native or native mode.
scalarEnumeration.1.3.6.1.4.1.6141.2.60.38.1.1.1.8
wwpLeosPbtServiceVlanTpid
When operating in native mode, this is the value of the service vlan TPID that will be used if retain-stag is set to TRUE. This is configurable only in native mode PBT. In non-nat…
scalarOctetString.1.3.6.1.4.1.6141.2.60.38.1.1.1.9