wwpPortRateLimitValue

WWP-EXT-BRIDGE-MIB · .1.3.6.1.4.1.6141.2.4.1.1.1.1.19
MIB view Table view

Object

column r/w Bits per second Integer32 
The value of this object represents the desired bit-rate limit 
for this port.  When the rate limiting mechanism is enabled for
this port, this value is enforced to the best extent possible by
the device.
              
For some devices the actual maximum bit-rate allowed may exceed the
rate limit parameter under certain circumstances due to hardware and
software limitations.

Context

MIB
WWP-EXT-BRIDGE-MIB
OID
.1.3.6.1.4.1.6141.2.4.1.1.1.1.19
Type
column
Access
readwrite
Status
current
Units
Bits per second
Parent
wwpPortEntry
Table
wwpPortTable
Siblings
18

Syntax

Bits per second Integer32

Values & Constraints

Object Constraints
range: 0-2147483647

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
wwpPortId
Port ID for the instance. Port ID's start at 1, and are consecutive for each additional port. This port Id should refer to the dot1dBasePort in the Dot1dBasePortEntry.
columnInteger32.1.3.6.1.4.1.6141.2.4.1.1.1.1.1
wwpPortAdminDuplex
The desired mode for the port. It can be set to either half or full duplex operation but not to auto.The default value for this object depends upon the platform.
columnEnumeration.1.3.6.1.4.1.6141.2.4.1.1.1.1.10
wwpPortOperDuplex
The current duplex mode of the port.
columnEnumeration.1.3.6.1.4.1.6141.2.4.1.1.1.1.11
wwpPortAdminFlowCtrl
Configures the ports flow control operation. Need to check 802.3x for additional modes for gig ports.
columnEnumeration.1.3.6.1.4.1.6141.2.4.1.1.1.1.12
wwpPortOperFlowCtrl
Shows ports flow control configuration.
columnEnumeration.1.3.6.1.4.1.6141.2.4.1.1.1.1.13
wwpPortTagged
The port tagged Status can be set to tagged or untagged. If a port is part of more than one VLAN, then the port Status should be 'tagged'.
columnEnumeration.1.3.6.1.4.1.6141.2.4.1.1.1.1.14
wwpPortUntaggedPriority
The 802.1p packet priority to be assigned to packets associated with this port that do not have an 802.1Q VLAN header.
columnEnumeration.1.3.6.1.4.1.6141.2.4.1.1.1.1.15
wwpPortMaxFrameSize
Setting this object will set the max frame size allowed on a port. The max frame size can vary between 1522 bytes till 9216 bytes. Default value is 1522 bytes
columnInteger32.1.3.6.1.4.1.6141.2.4.1.1.1.1.16
wwpPortIngressFiltering
When this is true(1) the device will discard incoming frames for VLANs which do not include this Port in its Member set. When false(2), the port will accept all incoming frames.
columnEnumeration.1.3.6.1.4.1.6141.2.4.1.1.1.1.17
wwpPortRateLimitState
When set to true, the rate limiting mechanism is enabled for this port. When set to false, the rate limiting mechanism is disabled for this port.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.6141.2.4.1.1.1.1.18
wwpPortType
The port type for the port.
columnEnumeration.1.3.6.1.4.1.6141.2.4.1.1.1.1.2
wwpPortName
Friendly name for the port.
columnOctetString.1.3.6.1.4.1.6141.2.4.1.1.1.1.3
wwpPortPhysAddr
The ethernet MAC address for the port. This information can also be achieved via dot1dTpFdbTable
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.6141.2.4.1.1.1.1.4
wwpPortAutoNeg
The object sets the port to AUTO NEG MOde and vice versa. Specific platforms may have requirements of configuring speed before moving the port to out of AUTO-NEG mode.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.6141.2.4.1.1.1.1.5
wwpPortAdminStatus
The desired state of the port.
columnEnumeration.1.3.6.1.4.1.6141.2.4.1.1.1.1.6
wwpPortOperStatus
The current operational state of Port.
columnEnumeration.1.3.6.1.4.1.6141.2.4.1.1.1.1.7
wwpPortAdminSpeed
Desired speed of the port. Set the port speed to be either 10MB, 100MB, or gig. The Management Station can't set the wwpPortAdminSpeed to auto. The default value for this object …
columnEnumeration.1.3.6.1.4.1.6141.2.4.1.1.1.1.8
wwpPortOperSpeed
The current operational speed of the port in MB.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6141.2.4.1.1.1.1.9