wwpPortOperStatus
WWP-EXT-BRIDGE-MIB ·
.1.3.6.1.4.1.6141.2.4.1.1.1.1.7
Object
column
Enumeration
The current operational state of Port.
Context
- MIB
- WWP-EXT-BRIDGE-MIB
- OID
.1.3.6.1.4.1.6141.2.4.1.1.1.1.7- Type
- column
- Access
- readonly
- Status
- current
- Parent
- wwpPortEntry
- Table
- wwpPortTable
- Siblings
- 18
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | up |
2 | down |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| wwpPortId Port ID for the instance. Port ID's start at 1, and are
consecutive for each additional port. This port Id should
refer to the dot1dBasePort in the Dot1dBasePortEntry. | column | Integer32 | .1.3.6.1.4.1.6141.2.4.1.1.1.1.1 |
| wwpPortAdminDuplex The desired mode for the port. It can be set to either half or full duplex
operation but not to auto.The default value for this object
depends upon the platform. | column | Enumeration | .1.3.6.1.4.1.6141.2.4.1.1.1.1.10 |
| wwpPortOperDuplex The current duplex mode of the port. | column | Enumeration | .1.3.6.1.4.1.6141.2.4.1.1.1.1.11 |
| wwpPortAdminFlowCtrl Configures the ports flow control operation. Need to check
802.3x for additional modes for gig ports. | column | Enumeration | .1.3.6.1.4.1.6141.2.4.1.1.1.1.12 |
| wwpPortOperFlowCtrl Shows ports flow control configuration. | column | Enumeration | .1.3.6.1.4.1.6141.2.4.1.1.1.1.13 |
| wwpPortTagged The port tagged Status can be set to tagged or untagged. If a port
is part of more than one VLAN, then the port Status should be 'tagged'. | column | Enumeration | .1.3.6.1.4.1.6141.2.4.1.1.1.1.14 |
| wwpPortUntaggedPriority The 802.1p packet priority to be assigned to packets associated
with this port that do not have an 802.1Q VLAN header. | column | Enumeration | .1.3.6.1.4.1.6141.2.4.1.1.1.1.15 |
| wwpPortMaxFrameSize Setting this object will set the max frame size allowed on a
port. The max frame size can vary between 1522 bytes till
9216 bytes. Default value is 1522 bytes | column | Integer32 | .1.3.6.1.4.1.6141.2.4.1.1.1.1.16 |
| wwpPortIngressFiltering When this is true(1) the device will discard incoming
frames for VLANs which do not include this Port in its
Member set. When false(2), the port will accept all
incoming frames. | column | Enumeration | .1.3.6.1.4.1.6141.2.4.1.1.1.1.17 |
| wwpPortRateLimitState When set to true, the rate limiting mechanism is enabled for
this port. When set to false, the rate limiting mechanism
is disabled for this port. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6141.2.4.1.1.1.1.18 |
| wwpPortRateLimitValue The value of this object represents the desired bit-rate limit
for this port. When the rate limiting mechanism is enabled for
this port, this value is enforced to the best exten… | column | Bits per second Integer32 | .1.3.6.1.4.1.6141.2.4.1.1.1.1.19 |
| wwpPortType The port type for the port. | column | Enumeration | .1.3.6.1.4.1.6141.2.4.1.1.1.1.2 |
| wwpPortName Friendly name for the port. | column | OctetString | .1.3.6.1.4.1.6141.2.4.1.1.1.1.3 |
| wwpPortPhysAddr The ethernet MAC address for the port. This information can also
be achieved via dot1dTpFdbTable | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.6141.2.4.1.1.1.1.4 |
| wwpPortAutoNeg The object sets the port to AUTO NEG MOde and vice versa.
Specific platforms may have requirements of configuring
speed before moving the port to out of AUTO-NEG mode. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6141.2.4.1.1.1.1.5 |
| wwpPortAdminStatus The desired state of the port. | column | Enumeration | .1.3.6.1.4.1.6141.2.4.1.1.1.1.6 |
| wwpPortAdminSpeed Desired speed of the port.
Set the port speed to be either 10MB, 100MB, or gig.
The Management Station can't set the wwpPortAdminSpeed to auto.
The default value for this object … | column | Enumeration | .1.3.6.1.4.1.6141.2.4.1.1.1.1.8 |
| wwpPortOperSpeed The current operational speed of the port in MB. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6141.2.4.1.1.1.1.9 |