vdslLineConfHamBandMask
VDSL-LINE-MIB ·
.1.3.6.1.2.1.10.97.1.1.11.1.36
Object
column
r/w
Bits
The transmit power spectral density mask code, used
to avoid interference with HAM (Handheld Amateur Radio)
radio bands by introducing power control (notching) in one
or more of these bands.
Amateur radio band notching is defined in the VDSL
spectrum as follows:
Band Start Frequency Stop Frequency
---- ------------------ --------------------------------
30m 1810 kHz 2000 kHz
40m 3500 kHz 3800 kHz (ETSI); 4000 kHz (ANSI)
80m 7000 kHz 7100 kHz (ETSI); 7300 kHz (ANSI)
160m 10100 kHz 10150 kHz
Notching for each standard band can be enabled or disabled
via the bit mask.
Two custom notches may be specified. If either of these
are enabled via the bit mask, then the following objects
MUST be specified:
If customNotch1 is enabled, then both
vdslLineConfCustomNotch1Start
vdslLineConfCustomNotch1Stop
MUST be specified.
If customNotch2 is enabled, then both
vdslLineConfCustomNotch2Start
vdslLineConfCustomNotch2Stop
MUST be specified.
Context
- MIB
- VDSL-LINE-MIB
- OID
.1.3.6.1.2.1.10.97.1.1.11.1.36- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- vdslLineConfProfileEntry
- Table
- vdslLineConfProfileTable
- Siblings
- 45
Syntax
Bits
Values & Constraints
Enumerated Values
0 | customNotch1 |
1 | customNotch2 |
2 | amateurBand30m |
3 | amateurBand40m |
4 | amateurBand80m |
5 | amateurBand160m |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| vdslLineConfProfileName This object identifies a row in this table.
A default profile with an index of 'DEFVAL', will
always exist and its parameters will be set to vendor
specific values,… | column | OctetString | .1.3.6.1.2.1.10.97.1.1.11.1.1 |
| vdslLineConfUpMinSnrMgn Specifies the minimum upstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0 to 31.75 dB. | column | 0.25dBm Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.10 |
| vdslLineConfUpTargetSnrMgn Specifies the target upstream Signal/Noise Margin in
units of 0.25 dB, for a range of 0 to 31.75 dB. This
is the Noise Margin the transceivers must achieve with
a BER of 10^-7 or… | column | 0.25dBm Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.11 |
| vdslLineConfDownFastMaxDataRate Specifies the maximum downstream fast channel
data rate in steps of 1000 bits/second. | column | kbps SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.12 |
| vdslLineConfDownFastMinDataRate Specifies the minimum downstream fast channel
data rate in steps of 1000 bits/second. | column | kbps SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.13 |
| vdslLineConfDownSlowMaxDataRate Specifies the maximum downstream slow channel
data rate in steps of 1000 bits/second.
The maximum aggregate downstream transmit speed
of the line can be derived fro… | column | kbps SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.14 |
| vdslLineConfDownSlowMinDataRate Specifies the minimum downstream slow channel
data rate in steps of 1000 bits/second.
The minimum aggregate downstream transmit speed
of the line can be derived fro… | column | kbps SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.15 |
| vdslLineConfUpFastMaxDataRate Specifies the maximum upstream fast channel
data rate in steps of 1000 bits/second.
The maximum aggregate upstream transmit speed
of the line can be derived from th… | column | kbps SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.16 |
| vdslLineConfUpFastMinDataRate Specifies the minimum upstream fast channel
data rate in steps of 1000 bits/second.
The minimum aggregate upstream transmit speed
of the line can be derived from th… | column | kbps SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.17 |
| vdslLineConfUpSlowMaxDataRate Specifies the maximum upstream slow channel
data rate in steps of 1000 bits/second. | column | kbps SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.18 |
| vdslLineConfUpSlowMinDataRate Specifies the minimum upstream slow channel
data rate in steps of 1000 bits/second. | column | kbps SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.19 |
| vdslLineConfDownRateMode Specifies the rate selection behavior for the line
in the downstream direction.
manual(1) forces the rate to the configured rate
adaptAtInit(2) adapts the li… | column | Enumeration | .1.3.6.1.2.1.10.97.1.1.11.1.2 |
| vdslLineConfDownRateRatio For dynamic rate adaptation at startup, the allocation
of data rate in excess of the minimum data rate for each
channel is controlled by the object. This object specifies
the rat… | column | percent Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.20 |
| vdslLineConfUpRateRatio For dynamic rate adaptation at startup, the allocation
of data rate in excess of the minimum data rate for each
channel is controlled by the object. This object specifies
the rat… | column | percent Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.21 |
| vdslLineConfDownMaxInterDelay Specifies the maximum interleave delay for the
downstream slow channel. | column | milliseconds Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.22 |
| vdslLineConfUpMaxInterDelay Specifies the maximum interleave delay for the
upstream slow channel. | column | milliseconds Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.23 |
| vdslLineConfDownPboControl Downstream power backoff (PBO) control for this
line. For transceivers which do not support downstream
PBO control, this object MUST be fixed at disabled(1).
If auto(2) is select… | column | Enumeration | .1.3.6.1.2.1.10.97.1.1.11.1.24 |
| vdslLineConfUpPboControl Upstream power backoff (PBO) control for this
line. For transceivers which do not support upstream
PBO control, this object MUST be fixed at disabled(1).
If auto(2) is selected, … | column | Enumeration | .1.3.6.1.2.1.10.97.1.1.11.1.25 |
| vdslLineConfDownPboLevel Specifies the downstream backoff level to be used
when vdslLineConfDownPboControl = manual(3). | column | 0.25dB Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.26 |
| vdslLineConfUpPboLevel Specifies the upstream backoff level to be used
when vdslLineConfUpPboControl = manual(3). | column | 0.25dB Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.27 |
| vdslLineConfDeploymentScenario The VDSL line deployment scenario. When using
fttCab(1), the VTU-C is located in a street cabinet.
When using fttEx(2), the VTU-C is located at the
central office. Changes to th… | column | Enumeration | .1.3.6.1.2.1.10.97.1.1.11.1.28 |
| vdslLineConfAdslPresence Indicates presence of ADSL service in the associated
cable bundle/binder.
none(1) indicates no ADSL service in the bundle
adslOverPots(2) indicates ADSL ser… | column | Enumeration | .1.3.6.1.2.1.10.97.1.1.11.1.29 |
| vdslLineConfUpRateMode Specifies the rate selection behavior for the line
in the upstream direction.
manual(1) forces the rate to the configured rate
adaptAtInit(2) adapts the line… | column | Enumeration | .1.3.6.1.2.1.10.97.1.1.11.1.3 |
| vdslLineConfApplicableStandard The VDSL standard to be used for the line.
ansi(1) indicates ANSI standard
etsi(2) indicates ETSI standard
itu(3) indicates ITU standard
other(4) … | column | Enumeration | .1.3.6.1.2.1.10.97.1.1.11.1.30 |
| vdslLineConfBandPlan The VDSL band plan to be used for the line.
bandPlan997(1) is to be used for
ITU-T G.993.1 Bandplan-B
ETSI Bandplan
ANSI Plan 997
band… | column | Enumeration | .1.3.6.1.2.1.10.97.1.1.11.1.31 |
| vdslLineConfBandPlanFx The frequency limit between bands D2 and U2 when
vdslLineConfBandPlan is set to bandPlanFx(3). | column | kHz Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.32 |
| vdslLineConfBandOptUsage Defines the VDSL link use of the optional frequency
range [25kHz - 138kHz] (Opt).
unused(1) indicates Opt is unused
upstream(2) indicates Opt usage is for ups… | column | Enumeration | .1.3.6.1.2.1.10.97.1.1.11.1.33 |
| vdslLineConfUpPsdTemplate The upstream PSD template to be used for the line.
Here, templateMask1(1) refers to a notched mask that
limits the transmitted PSD within the internationally
standardized HAM (Han… | column | Enumeration | .1.3.6.1.2.1.10.97.1.1.11.1.34 |
| vdslLineConfDownPsdTemplate The downstream PSD template to be used for the line.
Here, templateMask1(1) refers to a notched mask that
limits the transmitted PSD within the internationally
standardized HAM (H… | column | Enumeration | .1.3.6.1.2.1.10.97.1.1.11.1.35 |
| vdslLineConfCustomNotch1Start Specifies the start frequency of custom HAM (Handheld
Amateur Radio) notch 1. vdslLineConfCustomNotch1Start MUST
be less than or equal to vdslLineConfCustomNotch1Stop. | column | kHz SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.37 |
| vdslLineConfCustomNotch1Stop Specifies the stop frequency of custom HAM (Handheld
Amateur Radio) notch 1. vdslLineConfCustomNotch1Stop MUST
be greater than or equal to vdslLineConfCustomNotch1Start. | column | kHz SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.38 |
| vdslLineConfCustomNotch2Start Specifies the start frequency of custom HAM (Handheld
Amateur Radio) notch 2. vdslLineConfCustomNotch2Start MUST
be less than or equal to vdslLineConfCustomNotch2Stop. | column | kHz SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.39 |
| vdslLineConfDownMaxPwr Specifies the maximum aggregate downstream power
level in the range 0 to 14.5 dBm. | column | 0.25dBm Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.4 |
| vdslLineConfCustomNotch2Stop Specifies the stop frequency of custom HAM (Handheld
Amateur Radio) notch 2. vdslLineConfCustomNotch2Stop MUST
be greater than or equal to vdslLineConfCustomNotch2Start. | column | kHz SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.40 |
| vdslLineConfDownTargetSlowBurst Specifies the target level of impulse noise (burst)
protection for an interleaved (slow) channel. | column | microseconds Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.41 |
| vdslLineConfUpTargetSlowBurst Specifies the target level of impulse noise (burst)
protection for an interleaved (slow) channel. | column | microseconds Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.42 |
| vdslLineConfDownMaxFastFec This parameter provisions the maximum level of Forward
Error Correction (FEC) redundancy related overhead to
be maintained for a fast channel. | column | % Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.43 |
| vdslLineConfUpMaxFastFec This parameter provisions the maximum level of Forward
Error Correction (FEC) redundancy related overhead to
be maintained for a fast channel. | column | % Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.44 |
| vdslLineConfLineType This parameter provisions the VDSL physical entity at
start-up by defining whether and how the line will be
channelized, i.e., which channel type(s) are supported.
If the line is … | column | Enumeration | .1.3.6.1.2.1.10.97.1.1.11.1.45 |
| vdslLineConfProfRowStatus This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to 'active'.
When 'active' is … | column | SNMPv2-TCRowStatus | .1.3.6.1.2.1.10.97.1.1.11.1.46 |
| vdslLineConfUpMaxPwr Specifies the maximum aggregate upstream power
level in the range 0 to 14.5 dBm. | column | 0.25dBm Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.5 |
| vdslLineConfDownMaxSnrMgn Specifies the maximum downstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0 to 31.75 dB. | column | 0.25dBm Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.6 |
| vdslLineConfDownMinSnrMgn Specifies the minimum downstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0 to 31.75 dB. | column | 0.25dBm Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.7 |
| vdslLineConfDownTargetSnrMgn Specifies the target downstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0 to 31.75 dB.
This is the Noise Margin the transceivers must achieve
with a BER of 10^-7 o… | column | 0.25dBm Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.8 |
| vdslLineConfUpMaxSnrMgn Specifies the maximum upstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0 to 31.75 dB. | column | 0.25dBm Unsigned32 | .1.3.6.1.2.1.10.97.1.1.11.1.9 |