tnSvcEndPointRevertTimeCountDn
TN-SERV-MIB ·
.1.3.6.1.4.1.7483.6.1.2.4.2.19.1.16
Object
column
seconds Integer32
The value of tnSvcEndPointRevertTimeCountDn indicates the timer
count down before reverting back to the primary spoke-sdp
defined on this service endpoint, after having failed over to
a backup spoke-sdp.
This timer count down begins after primary Spoke SDP becomes
operational.
The value of -1 indicates when revert is not-applicable.
Context
- MIB
- TN-SERV-MIB
- OID
.1.3.6.1.4.1.7483.6.1.2.4.2.19.1.16- Type
- column
- Access
- readonly
- Status
- current
- Units
- seconds
- Parent
- tnSvcEndPointEntry
- Table
- tnSvcEndPointTable
- Siblings
- 25
Syntax
seconds Integer32
Values & Constraints
Object Constraints
range: -1-600
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| tnSvcEndPointName The value of tnSvcEndPointName specifies the name of the service
endpoint. | column | TN-TC-MIBTNamedItem | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.1 |
| tnSvcEndPointForceSwitchOverSdpId The value of tnSvcEndPointForceSwitchOverSdpId specifies the SDP
bind to switch over to when tnSvcEndPointForceSwitchOver is set
to 'doAction'. If the value of this object is non … | column | TN-TC-MIBSdpBindId | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.10 |
| tnSvcEndPointActiveHoldDelay The value of tnSvcEndPointActiveHoldDelay specifies the amount
of time in deci-seconds to hold the active state before going
into the standby state when a local MC-LAG SAP goes do… | column | deci-seconds Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.11 |
| tnSvcEndPointIgnoreStandbySig The value of tnSvcEndPointIgnoreStandbySig specifies whether the
local internal tasks will take into account the 'pseudo-wire
forwarding standby' bit received from the LDP peer wh… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.12 |
| tnSvcEndPointMacPinning The value of tnSvcEndPointMacPinning specifies whether or not
MAC address pinning is active on this end-point. | column | TN-TC-MIBTmnxEnabledDisabled | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.13 |
| tnSvcEndPointMacLimit The value of the object tnSvcEndPointMacLimit specifies the
maximum number of learned and static entries allowed for this
end-point.
The value 0 means: no limit for… | column | Integer32 | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.14 |
| tnSvcEndPointSuppressStandbySig The value of the object tnSvcEndPointSuppressStandbySig specifies
whether the 'pseudo wire forwarding standby' bit will be sent
to the LDP peer whenever the spoke SDP
'tnSvcEndPoi… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.15 |
| tnSvcEndPointTxActiveChangeCount The value of tnSvcEndPointTxActiveChangeCount indicates the
number of times active transmit change has taken place in this
endpoint. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.17 |
| tnSvcEndPointTxActiveLastChange The value of tnSvcEndPointTxActiveLastChange indicates the
value of sysUpTime at the time of the last active transmit
change in this endpoint. | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.18 |
| tnSvcEndPointTxActiveUpTime The value of tnSvcEndPointTxActiveUpTime indicates the active
'up' time (in hundredths of a second) of the end-point object
that is current transmit active. | column | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.19 |
| tnSvcEndPointRowStatus The value of tnSvcEndPointRowStatus is used for the creation and
deletion of service endpoints. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.2 |
| tnSvcEndPointMCEPId The value of tnSvcEndPointMCEPId specifies the multi-chassis
end-point identifier assigned to this endpoint. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.20 |
| tnSvcEndPointMCEPPeerAddrType The value of tnSvcEndPointMCEPPeerAddrType specifies the
address type of tnSvcEndPointMCEPPeerAddr object.
An 'inconsistentValue' error is returned if this object i… | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.21 |
| tnSvcEndPointMCEPPeerAddr The value of tnSvcEndPointMCEPPeerAddr specifies the
IP address of multi-chassis end-point peer.
An 'inconsistentValue' error is returned if this object is
set to n… | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.22 |
| tnSvcEndPointMCEPPeerName The value of tnSvcEndPointMCEPPeerName specifies the name of
multi-chassis end-point peer
TIMETRA-MC-REDUNDANCY-MIB::tmnxMcPeerName.
An 'inconsistentValue' error is… | column | TN-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.23 |
| tnSvcEndPointBlockOnMeshFail The value of tnSvcEndPointBlockOnMeshFail specifies that the
operational status of spoke-SDPs in the endpoint will be
affected by the operational status of associated mesh SDPs in… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.24 |
| tnSvcEndPointMCEPPsvModeActive The value of tnSvcEndPointMCEPPsvModeActive indicates whether
passive-mode behavior is currently active on this multi-chassis
end-point. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.25 |
| tnSvcEndPointStandbySigMaster The value of tnSvcEndPointStandbySigMaster specifies whether
PW standby bit will be sent to T-LDP peer whenever spoke-SDPs
of this endpoint are selected as standby. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.26 |
| tnSvcEndPointDescription The value of tnSvcEndPointDescription specifies the textual
description of this service endpoint. | column | TN-TC-MIBServObjDesc | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.3 |
| tnSvcEndPointRevertTime The value of tnSvcEndPointRevertTime specifies the time to wait
before reverting back to the primary spoke-sdp defined on this
service endpoint, after having failed over to a back… | column | seconds Integer32 | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.4 |
| tnSvcEndPointTxActiveType The value of tnSvcEndPointTxActiveType indicates the type of
end-point object that is current transmit active. | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.5 |
| tnSvcEndPointTxActivePortId The value of tnSvcEndPointTxActivePortId indicates the Port ID
of the SAP that is transmit active. This object is only valid
when tnSvcEndPointTxActiveType is 'sap'. | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.6 |
| tnSvcEndPointTxActiveEncap The value of tnSvcEndPointTxActiveEncap indicates the
encapsulation value of the SAP that is transmit active. This
object is only valid when tnSvcEndPointTxActiveType is 'sap'. | column | TN-TC-MIBTmnxEncapVal | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.7 |
| tnSvcEndPointTxActiveSdpId The value of tnSvcEndPointTxActiveSdpId indicates the SDP bind
ID of the SDP bind that is transmit active. This object is only
valid when tnSvcEndPointTxActiveType is 'sdpBind'. | column | TN-TC-MIBSdpBindId | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.8 |
| tnSvcEndPointForceSwitchOver The value of tnSvcEndPointForceSwitchOver specifies whether to
force a switchover of the active SDP bind. When it is set to
'doAction', the SDP bind specified by
tnSvcEndPointForc… | column | TN-TC-MIBTmnxActionType | .1.3.6.1.4.1.7483.6.1.2.4.2.19.1.9 |