tnPortEtherXGigMode
TN-PORT-MIB ·
.1.3.6.1.4.1.7483.6.1.2.2.4.4.1.10
Object
column
r/w
Enumeration
The tnPortEtherXGigMode variable specifies whether the Ethernet interface is in LAN or WAN mode. tnPortEtherXGigMode must be 'notApplicable' if tnPortClass is not 'xgige'.
Context
- MIB
- TN-PORT-MIB
- OID
.1.3.6.1.4.1.7483.6.1.2.2.4.4.1.10- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- tnPortEtherEntry
- Table
- tnPortEtherTable
- Siblings
- 33
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | notApplicable |
1 | lan |
2 | wan |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| tnPortEtherMTU The size of the largest packet which can be sent/received
on the Ethernet physical interface, specified in octets. For
interfaces that are used for transmitting network datagrams… | column | bytes Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.1 |
| tnPortEtherEgressRate The tnPortEtherEgressRate variable specifies the maximum egress
bandwidth (in kilobits per second) that the Ethernet interface
can generate. A value of -1 means that the limit is … | column | Integer32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.11 |
| tnPortEtherDot1qEtype The tnPortEtherDot1qEtype variable indicates the ethertype expected
when the port's encapsulation type is dot1qEncap. | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.12 |
| tnPortEtherQinqEtype The tnPortEtherQinqEtype variable indicates the ethertype expected
when the port's encapsulation type is qinqEncap. | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.13 |
| tnPortEtherIngressRate The tnPortEtherIngressRate variable specifies the maximum ingress
bandwidth (in mega-bits per second) that the Ethernet interface
can receive. A value of -1 means that the limit i… | column | mega-bits per second Integer32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.14 |
| tnPortEtherReportAlarm The value of tnPortEtherReportAlarm determines when and if to
generate tnEqPortEtherAlarm and tnEqPortEtherAlarmClear. | column | TmnxPortEtherReportStatus | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.15 |
| tnPortEtherReportAlarmStatus The value of tnPortEtherReportAlarmStatus indicates the alarms on
this port. | column | TmnxPortEtherReportStatus | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.16 |
| tnPortEtherPkts1519toMax The total number of packets received that were longer than 1518 octets
but less than the maximum frame size for the particular medium, usually
12287 octets (excluding framing bits… | column | Packets SNMPv2-SMICounter32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.17 |
| tnPortEtherHCOverPkts1519toMax The number of times the associated tnPortEtherPkts1519toMax
counter has overflowed. | column | Packets SNMPv2-SMICounter32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.18 |
| tnPortEtherHCPkts1519toMax The total number of packets (including bad packets) received that were
between 1519 octets in length and the maximum frame size, usually 12287
octets inclusive (excluding framing … | column | Packets SNMPv2-SMICounter64 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.19 |
| tnPortEtherDuplex The tnPortEtherDuplex variable specifies the duplex mode used by
the Ethernet interface if tnPortEtherAutoNegotiate has a value of
'false' or 'limited'. If tnPortEtherAutoNegotiat… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.2 |
| tnPortEtherLacpTunnel The value of tnPortEtherLacpTunnel specifies whether the LACP
packet tunneling for the ethernet port is enabled or disabled.
When tunneling is enabled, the port will not process a… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.20 |
| tnPortEtherDownWhenLoopedEnabled The value of tnPortEtherDownWhenLoopedEnabled specifies whether
physical loop detection for the Ethernet port is enabled or
disabled. When enabled, the port will periodically sen… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.21 |
| tnPortEtherDownWhenLoopedKeepAlive The tnPortEtherDownWhenLoopedKeepAlive variable specifies the
number of seconds between each keep alive PDU transmission. | column | seconds Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.22 |
| tnPortEtherDownWhenLoopedRetry The tnPortEtherDownWhenLoopedRetry variable specifies the minimum
number of seconds the port should wait after detecting a loop before
tnPortState can be set to 'up'. A value of … | column | seconds Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.23 |
| tnPortEtherDownWhenLoopedState The value of tnPortEtherDownWhenLoopedState indicates whether
a physical loop has been detected on the port or not. If
tnPortEtherDownWhenLoopedEnabled is set to 'false', this va… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.24 |
| tnPortEtherPBBEtype The tnPortEtherPBBEtype variable indicates the Ethertype expected
for Provider Backbone Bridging Frames. | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.25 |
| tnPortEtherSingleFiber tnPortEtherSingleFiber is used to enable/disable packet gathering and
redirection of IP packets from a single fiber on RX port of the
Ethernet interface and redistribute packets t… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.27 |
| tnPortEtherSSM tnPortEtherSSM specifies whether or not synchronous
status messages (SSM) are enabled on the ethernet port. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.28 |
| tnPortEtherDWLUseBroadcastAddr tnPortEtherDWLUseBroadcastAddr specifies whether or not the
Down When Looped destination MAC address is the broadcast address,
'true (1)', or the local port mac address, as specif… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.29 |
| tnPortEtherSpeed The tnPortEtherSpeed variable specifies the link speed of the
Ethernet interface if tnPortEtherAutoNegotiate has a value of
'false' or 'limited'. If tnPortEtherAutoNegotiate has … | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.3 |
| tnPortEtherSSMCodeType The value of tnPortEtherSSMCodeType specifies the code-type
used by the Synchronous Status Message (SSM) channel. | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.30 |
| tnPortEtherSSMTxDus The value of tnPortEtherSSMTxDus specifies whether or not the
value 0xF (dus/dnu) is forced in the Synchronous Status Message (SSM)
channel. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.31 |
| tnPortEtherSSMRxEsmc The value of tnPortEtherSSMRxEsmc indicates the SSM code received on
the Ethernet Synchronization Messaging Channel of the Ethernet port.
The value returned for thi… | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.32 |
| tnPortEtherSSMTxQualityLevel The value of tnPortEtherSSMTxQualityLevel indicates the quality
level transmitted in the Ethernet Synchronization Messaging Channel. | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.33 |
| tnPortEtherQinqEtypelink Ethertype profile ID which is referenced to tnCardEtherTypeProfileTable.
If tnPortEtherQinqEtypelink is zero, it indicates no associations.
If there is an association, tnPortEther… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.34 |
| tnPortEtherOperEgressRate The tnPortEtherOperEgressRate variable specifies the operational egress
bandwidth (in kilobits per second) that the Ethernet interface
generates. A value of -1 means that the limi… | column | Integer32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.35 |
| tnPortEtherAutoNegotiate When the value of tnPortEtherAutoNegotiate is 'true', the Ethernet
interface will automatically negotiate link parameters with the far
end (including speed and duplex), and will a… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.4 |
| tnPortEtherOperDuplex The tnPortEtherOperDuplex variable indicates the operational duplex
mode of the Ethernet interface. A value of 'fullDuplex' indicates that
the link is in full duplex mode. A valu… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.5 |
| tnPortEtherOperSpeed The tnPortEtherOperSpeed variable indicates the operational speed
of the Ethernet interface in mega-bits per second (mbps). If the value of
tnPortEtherAutoNegotiate is 'true', th… | column | mega-bits per second SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.6 |
| tnPortEtherAcctPolicyId The value of the accounting policy must be defined prior to associating
the policy with the ethernet port. Accounting policies can only be
associated with network ports.
A non-zer… | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.7 |
| tnPortEtherCollectStats Enable/disable the collection of accounting and statistical data
for the network ethernet port. When applying accounting policies the
data by default will be collected in the appr… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.8 |
| tnPortEtherMDIMDIX The tnPortEtherMDIMDIX variable indicates whether the Ethernet
interface is of type 'mdi' (Media Dependent Interface) or
'mdix' (Media Dependent Interface with crossover). If the … | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.9 |