tnPortEtherQinqEtypelink
TN-PORT-MIB ·
.1.3.6.1.4.1.7483.6.1.2.2.4.4.1.34
Object
Ethertype profile ID which is referenced to tnCardEtherTypeProfileTable. If tnPortEtherQinqEtypelink is zero, it indicates no associations. If there is an association, tnPortEtherQinqEtype shall equal to tnCardEthertypeQinQEtype, it means that the configuration per card will override the configuration per port. The profile ID 1 is associated all qinq port if no other profile is explicitly specified
Context
- MIB
- TN-PORT-MIB
- OID
.1.3.6.1.4.1.7483.6.1.2.2.4.4.1.34- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- tnPortEtherEntry
- Table
- tnPortEtherTable
- Siblings
- 33
Syntax
SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| tnPortEtherMTU The size of the largest packet which can be sent/received
on the Ethernet physical interface, specified in octets. For
interfaces that are used for transmitting network datagrams… | column | bytes Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.1 |
| tnPortEtherXGigMode The tnPortEtherXGigMode variable specifies whether the Ethernet
interface is in LAN or WAN mode. tnPortEtherXGigMode must be
'notApplicable' if tnPortClass is not 'xgige'. | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.10 |
| tnPortEtherEgressRate The tnPortEtherEgressRate variable specifies the maximum egress
bandwidth (in kilobits per second) that the Ethernet interface
can generate. A value of -1 means that the limit is … | column | Integer32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.11 |
| tnPortEtherDot1qEtype The tnPortEtherDot1qEtype variable indicates the ethertype expected
when the port's encapsulation type is dot1qEncap. | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.12 |
| tnPortEtherQinqEtype The tnPortEtherQinqEtype variable indicates the ethertype expected
when the port's encapsulation type is qinqEncap. | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.13 |
| tnPortEtherIngressRate The tnPortEtherIngressRate variable specifies the maximum ingress
bandwidth (in mega-bits per second) that the Ethernet interface
can receive. A value of -1 means that the limit i… | column | mega-bits per second Integer32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.14 |
| tnPortEtherReportAlarm The value of tnPortEtherReportAlarm determines when and if to
generate tnEqPortEtherAlarm and tnEqPortEtherAlarmClear. | column | TmnxPortEtherReportStatus | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.15 |
| tnPortEtherReportAlarmStatus The value of tnPortEtherReportAlarmStatus indicates the alarms on
this port. | column | TmnxPortEtherReportStatus | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.16 |
| tnPortEtherPkts1519toMax The total number of packets received that were longer than 1518 octets
but less than the maximum frame size for the particular medium, usually
12287 octets (excluding framing bits… | column | Packets SNMPv2-SMICounter32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.17 |
| tnPortEtherHCOverPkts1519toMax The number of times the associated tnPortEtherPkts1519toMax
counter has overflowed. | column | Packets SNMPv2-SMICounter32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.18 |
| tnPortEtherHCPkts1519toMax The total number of packets (including bad packets) received that were
between 1519 octets in length and the maximum frame size, usually 12287
octets inclusive (excluding framing … | column | Packets SNMPv2-SMICounter64 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.19 |
| tnPortEtherDuplex The tnPortEtherDuplex variable specifies the duplex mode used by
the Ethernet interface if tnPortEtherAutoNegotiate has a value of
'false' or 'limited'. If tnPortEtherAutoNegotiat… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.2 |
| tnPortEtherLacpTunnel The value of tnPortEtherLacpTunnel specifies whether the LACP
packet tunneling for the ethernet port is enabled or disabled.
When tunneling is enabled, the port will not process a… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.20 |
| tnPortEtherDownWhenLoopedEnabled The value of tnPortEtherDownWhenLoopedEnabled specifies whether
physical loop detection for the Ethernet port is enabled or
disabled. When enabled, the port will periodically sen… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.21 |
| tnPortEtherDownWhenLoopedKeepAlive The tnPortEtherDownWhenLoopedKeepAlive variable specifies the
number of seconds between each keep alive PDU transmission. | column | seconds Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.22 |
| tnPortEtherDownWhenLoopedRetry The tnPortEtherDownWhenLoopedRetry variable specifies the minimum
number of seconds the port should wait after detecting a loop before
tnPortState can be set to 'up'. A value of … | column | seconds Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.23 |
| tnPortEtherDownWhenLoopedState The value of tnPortEtherDownWhenLoopedState indicates whether
a physical loop has been detected on the port or not. If
tnPortEtherDownWhenLoopedEnabled is set to 'false', this va… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.24 |
| tnPortEtherPBBEtype The tnPortEtherPBBEtype variable indicates the Ethertype expected
for Provider Backbone Bridging Frames. | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.25 |
| tnPortEtherSingleFiber tnPortEtherSingleFiber is used to enable/disable packet gathering and
redirection of IP packets from a single fiber on RX port of the
Ethernet interface and redistribute packets t… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.27 |
| tnPortEtherSSM tnPortEtherSSM specifies whether or not synchronous
status messages (SSM) are enabled on the ethernet port. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.28 |
| tnPortEtherDWLUseBroadcastAddr tnPortEtherDWLUseBroadcastAddr specifies whether or not the
Down When Looped destination MAC address is the broadcast address,
'true (1)', or the local port mac address, as specif… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.29 |
| tnPortEtherSpeed The tnPortEtherSpeed variable specifies the link speed of the
Ethernet interface if tnPortEtherAutoNegotiate has a value of
'false' or 'limited'. If tnPortEtherAutoNegotiate has … | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.3 |
| tnPortEtherSSMCodeType The value of tnPortEtherSSMCodeType specifies the code-type
used by the Synchronous Status Message (SSM) channel. | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.30 |
| tnPortEtherSSMTxDus The value of tnPortEtherSSMTxDus specifies whether or not the
value 0xF (dus/dnu) is forced in the Synchronous Status Message (SSM)
channel. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.31 |
| tnPortEtherSSMRxEsmc The value of tnPortEtherSSMRxEsmc indicates the SSM code received on
the Ethernet Synchronization Messaging Channel of the Ethernet port.
The value returned for thi… | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.32 |
| tnPortEtherSSMTxQualityLevel The value of tnPortEtherSSMTxQualityLevel indicates the quality
level transmitted in the Ethernet Synchronization Messaging Channel. | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.33 |
| tnPortEtherOperEgressRate The tnPortEtherOperEgressRate variable specifies the operational egress
bandwidth (in kilobits per second) that the Ethernet interface
generates. A value of -1 means that the limi… | column | Integer32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.35 |
| tnPortEtherAutoNegotiate When the value of tnPortEtherAutoNegotiate is 'true', the Ethernet
interface will automatically negotiate link parameters with the far
end (including speed and duplex), and will a… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.4 |
| tnPortEtherOperDuplex The tnPortEtherOperDuplex variable indicates the operational duplex
mode of the Ethernet interface. A value of 'fullDuplex' indicates that
the link is in full duplex mode. A valu… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.5 |
| tnPortEtherOperSpeed The tnPortEtherOperSpeed variable indicates the operational speed
of the Ethernet interface in mega-bits per second (mbps). If the value of
tnPortEtherAutoNegotiate is 'true', th… | column | mega-bits per second SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.6 |
| tnPortEtherAcctPolicyId The value of the accounting policy must be defined prior to associating
the policy with the ethernet port. Accounting policies can only be
associated with network ports.
A non-zer… | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.7 |
| tnPortEtherCollectStats Enable/disable the collection of accounting and statistical data
for the network ethernet port. When applying accounting policies the
data by default will be collected in the appr… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.8 |
| tnPortEtherMDIMDIX The tnPortEtherMDIMDIX variable indicates whether the Ethernet
interface is of type 'mdi' (Media Dependent Interface) or
'mdix' (Media Dependent Interface with crossover). If the … | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.2.4.4.1.9 |