sdpOperTunnelFarEndInetAddr
TIMETRA-SDP-MIB ·
.1.3.6.1.4.1.6527.3.1.2.4.4.3.1.73
Object
column
OctetString
The value of sdpOperTunnelFarEndInetAddr indicates the operational IP
address of the remote end of the transport tunnel for this SDP.
If sdpTunnelFarEndInetAddress is not set, it will take the value from
sdpFarEndInetAddress.
Context
- MIB
- TIMETRA-SDP-MIB
- OID
.1.3.6.1.4.1.6527.3.1.2.4.4.3.1.73- Type
- column
- Access
- readonly
- Status
- current
- Parent
- sdpInfoEntry
- Table
- sdpInfoTable
- Siblings
- 72
Syntax
OctetString
Values & Constraints
Object Constraints
range: 0-0
range: 4-4
range: 16-16
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| sdpId SDP identifier. | column | TIMETRA-SERV-MIBSdpId | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.1 |
| sdpAdminPathMtu This object specifies the desired largest service frame size (in
octets) that can be transmitted through this SDP to the far-end ESR,
without requiring the packet to be fragmented… | column | Integer32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.10 |
| sdpOperPathMtu This object indicates the actual largest service frame size (in
octets) that can be transmitted through this SDP to the far-end ESR,
without requiring the packet to be fragmented.… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.11 |
| sdpKeepAliveAdminStatus This object is used to enable or disable the keep-alive protocol used
to determine the operating status of this SDP. | column | TIMETRA-TC-MIBTmnxEnabledDisabledAdminState | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.12 |
| sdpKeepAliveOperStatus The current status of the keep-alive protocol. The value 'alive'
indicates that the far-end ESR is replying the SDP Echo Requests
messages sent by this device indicating no error … | column | Enumeration | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.13 |
| sdpKeepAliveHelloTime This object specifies how often the SDP Echo Request messages are
transmitted on this SDP. | column | seconds Integer32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.14 |
| sdpKeepAliveMaxDropCount This object specifies the maximum number of consecutive SDP Echo
Request messages that can be unacknowledged before the keep-alive
protocol reports a fault. | column | Integer32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.15 |
| sdpKeepAliveHoldDownTime This object specifies the amount of time to wait before the keep-alive
operating status is eligible to enter the 'alive' state. | column | seconds Integer32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.16 |
| sdpLastMgmtChange The value of sysUpTime at the time of the most recent
management-initiated change to this SDP. | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.17 |
| sdpKeepAliveHelloMessageLength This object specifies the length of the SDP Echo Request messages
transmitted on this SDP. The default value of zero indicates that the
message length should be equal to the SDP's… | column | Integer32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.18 |
| sdpKeepAliveNumHelloRequestMessages The number of SDP Echo Request messages transmitted since the
keep-alive was administratively enabled or the counter was cleared. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.19 |
| sdpRowStatus This object specifies the status of this row. The only values
supported during a set operation are 'createAndGo' and 'destroy'. To
delete an entry from this table, the correspondi… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.2 |
| sdpKeepAliveNumHelloResponseMessages The number of SDP Echo Response messages received since the keep-alive
was administratively enabled or the counter was cleared. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.20 |
| sdpKeepAliveNumLateHelloResponseMessages The number of SDP Echo Response messages received after the
corresponding Request timeout timer expired. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.21 |
| sdpKeepAliveHelloRequestTimeout The number of seconds to wait for an SDP Echo Response message before
declaring a timeout. | column | seconds Integer32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.22 |
| sdpLdpEnabled When the value of this object is 'true' the transport LSPs are
signalled by LDP, as opposed to being provisioned static or
RSVP-signalled LSPs. This object applies only to MPLS SD… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.23 |
| sdpVlanVcEtype This object specifies the Ethertype used in frames sent out this SDP,
when the VC type is vlan. | column | Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.24 |
| sdpAdvertisedVllMtuOverride When the value of this object is 'true' the advertised MTU of a VLL
spoke SDP bind includes the 14-byte L2 header, so that it is backward
compatible with pre-2.0 software. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.25 |
| sdpOperFlags This object indicates all the conditions that affect the operating
status of this SDP. | column | Bits | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.26 |
| sdpLastStatusChange The value of sysUpTime at the time of the most recent operating status
change to this SDP. | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.27 |
| sdpMvplsMgmtService The value of sdpMvplsMgmtService indicates the service Id of the
service where the STP instance is running that is managing this SDP.
This object is only valid if sdpMvplsMgmtServ… | column | TIMETRA-TC-MIBTmnxServId | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.28 |
| sdpMvplsMgmtSdpBndId The value of sdpMvplsMgmtSdpBndId indicates which SDP bind in the
mVPLS instance specified in sdpMvplsMgmtService is controlling this
SDP. This object is only valid if sdpMvplsMgm… | column | TIMETRA-TC-MIBSdpBindId | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.29 |
| sdpDelivery This object specifies the type of delivery used by this SDP. The value
of this object must be specified when the row is created and cannot be
changed while the row status is 'acti… | column | Enumeration | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.3 |
| sdpCollectAcctStats The value of the object sdpCollectAcctStats specifies whether the
agent collects accounting statistics for this SDP. When the value is
'true' the agent collects accounting statist… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.30 |
| sdpAccountingPolicyId The value of sdpAccountingPolicyId specifies the policy to use to
collect accounting statistics on this SDP. The value zero indicates
that the agent should use the default account… | column | Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.31 |
| sdpClassFwdingEnabled The value of sdpClassFwdingEnabled specifies the admin state of
class-based forwarding on this SDP. When the value is 'true',
class-based forwarding is enabled. | column | TIMETRA-TC-MIBTmnxAdminStateTruthValue | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.32 |
| sdpClassFwdingDefaultLsp The value of sdpClassFwdingDefaultLsp specifies the LSP ID that is
used as a default when class-based forwarding is enabled on this SDP.
This object must be set when enabling clas… | column | TIMETRA-TC-MIBTmnxVRtrMplsLspID | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.33 |
| sdpClassFwdingMcLsp The value of sdpClassFwdingMcLsp specifies the LSP ID that all
multicast traffic will be forwarded on when class-based forwarding is
enabled on this SDP. When this object has its … | column | TIMETRA-TC-MIBTmnxVRtrMplsLspID | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.34 |
| sdpMetric The value of sdpMetric specifies the metric to be used within the
Tunnel Table Manager for decision making purposes. When multiple SDPs
going to the same destination exist, this v… | column | Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.35 |
| sdpAutoSdp The value of sdpAutoSdp indicates whether this is an Auto generated
SDP from RADIUS discovery or BGP auto-discovery. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.36 |
| sdpSnmpAllowed obsolete The value of sdpSnmpAllowed indicates if SNMP sets are allowed on this
SDP. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.37 |
| sdpPBBEtype This object specifies the Ethertype used in frames sent out on this
SDP when sdpBindVcType is 'vlan' for Provider Backbone Bridging
frames. | column | Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.38 |
| sdpBandwidthBookingFactor sdpBandwidthBookingFactor is used to calculate the max
SDP available bandwidth. The value of
sdpBandwidthBookingFactor specifies the percentage of the
SDP max available bandwidth… | column | Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.39 |
| sdpFarEndIpAddress obsolete This object specifies the IP address of the remote end of the GRE or
MPLS tunnel defined by this SDP. If sdpTunnelFarEndIpAddress is not
set, then sdpFarEndIpAddress also specifie… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.4 |
| sdpOperBandwidth The value of sdpOperBandwidth indicates the operational Bandwidth in
kilobits per seconds (Kbps) available for this SDP. The value
sdpOperBandwidth is determined by the sum of the… | column | kilobps SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.40 |
| sdpAvailableBandwidth The value of sdpAvailableBandwidth indicates the Bandwidth that is
still free for booking by the SDP bindings on the SDP. | column | kilobps SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.41 |
| sdpMaxBookableBandwidth The value of sdpMaxBookableBandwidth indicates the max Bandwidth that
the SDP has for booking by the SDP bindings. The value of
sdpMaxBookableBandwidth is calculated as follow:
… | column | kilobps SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.42 |
| sdpBookedBandwidth The value of sdpBookedBandwidth indicates the SDP Bandwidth that has
been booked by the SDP bindings. | column | kilobps SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.43 |
| sdpCreationOrigin The value of sdpCreationOrigin indicates the protocol or mechanism
which created this SDP. | column | TIMETRA-TC-MIBTmnxCreateOrigin | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.44 |
| sdpEnforceDiffServLspFc The value of sdpEnforceDiffServLspFc specifies whether service manager
must validate with RSVP the support of the FC by the LSP.
By default, the SDP uses the direct… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.45 |
| sdpMixedLspModeEnabled The value of sdpMixedLspModeEnabled specifies whether
mixed mode LSPs is enabled on this SDP. Setting the
value to 'true' allows LDP to be enabled and LSPs to
be configured at th… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.46 |
| sdpLspRevertTime The value of sdpLspRevertTime specifies the time to wait before
reverting back from LDP to the configured LSPs, after having failed
over to LDP.
When the value is -… | column | seconds Integer32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.47 |
| sdpLspRevertTimeCountDown The value of sdpLspRevertTimeCountDown indicated the timer countdown
before reverting back from LDP on this SDP. The timer countdown begins
after the first configured LSP becomes … | column | seconds Integer32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.48 |
| sdpLdpLspId The value of sdpLdpLspId indicates the Id for the LDP LSP if
sdpLdpEnabled is set to 'true' and there is a valid LDP route to the
sdpFarEndIpAddress or sdpFarEndNodeId. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.49 |
| sdpLspList obsolete When the SDP delivery specified by sdpDelivery is 'mpls', this object
specifies the list of LSPs used to reach the far-end ESR device.
All the LSPs in this list mus… | column | TIMETRA-SERV-MIBLspIdList | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.5 |
| sdpLdpActive obsolete The value of sdpLdpActive indicates whether LDP is active for the
current SDP. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.50 |
| sdpNetDomainName The value of sdpNetDomainName specifies the network-domain name this
SDP is associated with. The network-domain defines the list of network
interfaces this SDP can send traffic on… | column | TIMETRA-TC-MIBTNamedItemOrEmpty | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.51 |
| sdpEgressIfsNetDomainConsistent The value of sdpEgressIfsNetDomainConsistent indicates whether all the
egress network interfaces that can carry traffic on this SDP are
associated with the network-domain configur… | column | Enumeration | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.52 |
| sdpBgpTunnelEnabled The value of sdpBgpTunnelEnabled specifies whether the transport
tunnel is BGP as opposed to LDP or RSVP signalled LSPs.
This value cannot be set to 'true' if sdpLd… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.53 |
| sdpBgpTunnelLspId The value of sdpBgpTunnelLspId indicates the Id for the BGP Tunnel LSP
if sdpBgpTunnelEnabled is set to 'true' and there is a valid LDP route
to the sdpFarEndIpAddress. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.54 |
| sdpTunnelFarEndIpAddress obsolete The value of sdpTunnelFarEndIpAddress specifies the IP address of the
remote end of the transport tunnel for this SDP.
The value can only be changed while the admin… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.55 |
| sdpActiveLspType The value of sdpActiveLspType indicates the type of LSP that is
currently active on this SDP.
For sdpDelivery 'gre', the value is always 'not-applicable'.
… | column | Enumeration | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.56 |
| sdpBindingPort The value of sdpBindingPort specifies the port id for the binding on
this SDP.
The value of sdpPwPortOperStatus will be set to 'down' of all the
related SDP pseudo-… | column | TIMETRA-TC-MIBTmnxPortID | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.57 |
| sdpFarEndNodeId The value of sdpFarEndNodeId specifies the node identifier of the
far-end for this sdp.
The value of this object must be set to a non-default value when the
sdpDeli… | column | TIMETRA-TC-MIBTmnxMplsTpNodeID | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.58 |
| sdpFarEndGlobalId The value of sdpFarEndGlobalId specifies the global identifier of the
far-end for this sdp. | column | TIMETRA-TC-MIBTmnxMplsTpGlobalID | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.59 |
| sdpDescription Generic information about this SDP. | column | TIMETRA-SERV-MIBServObjDesc | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.6 |
| sdpFarEndInetAddressType The value of the object sdpFarEndInetAddressType specifies the address
type of sdpFarEndInetAddress. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.60 |
| sdpFarEndInetAddress The value of sdpFarEndInetAddress object specifies the IP address of
the remote end of the tunnel defined by this SDP. | column | OctetString | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.61 |
| sdpLocalEndInetAddressType The value of the object sdpLocalEndInetAddressType specifies the
address type of sdpLocalEndInetAddress. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.62 |
| sdpLocalEndInetAddress The value of sdpLocalEndInetAddress object specifies the IP address of
the local end of the tunnel defined by this SDP.
An 'inconsistentValue' error is returned whe… | column | OctetString | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.63 |
| sdpSourceBMacLSB The value of sdpSourceBMacLSB specifies the 16 least significant bits
(lsb) which when combined with the 32 most significant bits of the PBB
source-bmac specified by svcPbbSrcBVpl… | column | Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.64 |
| sdpControlPWVCId The value of sdpControlPWVCId specifies the spoke-SDP VC identifier to
be used as a control pseudo-wire to determine whether Shortest Path
Bridging Module (SPBM) advertises the vi… | column | TIMETRA-TC-MIBTmnxVcIdOrNone | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.65 |
| sdpControlPWIsActive The value of sdpControlPWIsActive indicates whether control
pseudo-wire is considered active on the Backbone Edge Bridge (BEB). | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.66 |
| sdpTunnelFarEndInetAddressType The value of sdpTunnelFarEndInetAddressType specifies the address type
of sdpTunnelFarEndInetAddress. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.67 |
| sdpTunnelFarEndInetAddress The value of sdpTunnelFarEndInetAddress specifies the IP address of
the remote end of the transport tunnel for this SDP.
This address must be different from sdpFarE… | column | OctetString | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.68 |
| sdpGreAllowFragmentation The value of sdpGreAllowFragmentation specifies whether to allow GRE
encapsulated packets to be sent without setting the DF bit for this
SDP.
This object is valid o… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.69 |
| sdpLabelSignaling This object specifies the signaling protocol used to obtain the
ingress and egress labels used in frames transmitted and received on
this SDP. When the value of this object is 'no… | column | Enumeration | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.7 |
| sdpFpeLspId The value of sdpFpeLspId indicates the identifier for the
forward-path-extension LSP when the SDP is created using 'fpe'. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.70 |
| sdpWeightedEcmpEnabled The value of sdpWeightedEcmpEnabled specifies the packets forwarded to
a set of ECMP tunnel next-hops which will be sprayed proportionally to
the load balancing weights configured… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.71 |
| sdpOperTunnelFarEndInetAddrType The value of sdpOperTunnelFarEndInetAddrType indicates the address
type of sdpOperTunnelFarEndInetAddr. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.72 |
| sdpAdminStatus The desired state of this SDP. | column | TIMETRA-TC-MIBServiceAdminStatus | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.8 |
| sdpOperStatus The operating state of this SDP. The value 'notAlive' is valid only
when keep-alive is enabled, and it means that the keep-alive operating
status is not alive. The value 'notReady… | column | Enumeration | .1.3.6.1.4.1.6527.3.1.2.4.4.3.1.9 |