tSyncIfTimingAdmBITSOutSource
TIMETRA-CHASSIS-MIB ·
.1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.28
Object
column
r/w
TmnxBITSOutSource
The value of tSyncIfTimingAdmBITSOutSource specifies the source of the
BITS (Building Integrated Timing Supply) output.
In an XRS-40 system, the extension chassis is synchronized with the
master chassis via the BITS ports. Two modes of operation are
permitted:
1) The BITS output ports of the master chassis CPMs are connected to
the BITS input ports of the extension chassis CPMs. In this mode,
tSyncIfTimingAdmBITSOutSource should be set to 'internalClock(2)',
to ensure that a valid clock signal is transmitted on the master
chassis's CPMs' BITS output ports.
2) The BITS input ports of all 4 CPMs are connected to external BITS
equipment. In this mode, the customer may connect the master
chassis's BITS output ports to the external BITS equipment's input
ports. This allows for recovered line references to be provided as
a frequency source into the external BITS equipment following the
inter-site synchronization mode of SDH/SONET. In this case,
tSyncIfTimingAdmBITSOutSource should be set to 'lineRef(1)'.
Context
- MIB
- TIMETRA-CHASSIS-MIB
- OID
.1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.28- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- tSyncIfTimingAdmEntry
- Table
- tSyncIfTimingAdmTable
- Siblings
- 37
Syntax
TmnxBITSOutSource
- Source
- TmnxBITSOutSource
- Base type
Enumeration
Values & Constraints
Type Values
1 | lineRef |
2 | internalClock |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| tSyncIfTimingAdmRevert The value of tSyncIfTimingAdmRevert specifies whether the reference
source will revert to a higher priority source that has been
re-validated or newly validated.
Th… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.1 |
| tSyncIfTimingAdmBITSIfType The value of tSyncIfTimingAdmBITSIfType specifies the interface type
of the BITS (Building Integrated Timing Supply) timing reference. | column | TmnxBITSIfType | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.10 |
| tSyncIfTimingAdmBITSAdminStatus The value of tSyncIfTimingAdmBITSAdminStatus specifies the desired
administrative status of the BITS (Building Integrated Timing Supply)
input timing reference. | column | TmnxPortAdminStatus | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.11 |
| tSyncIfTimingAdmRef1SrcHw obsolete The value of tSyncIfTimingAdmRef1SrcHw specifies the source HW Index
of the first timing reference if the source is not a port.
This can only be set to a valid HW I… | column | TmnxHwIndexOrZero | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.12 |
| tSyncIfTimingAdmRef1BITSIfType obsolete The value of tSyncIfTimingAdmRef1BITSIfType specifies the interface
type of the first timing reference if the source is BITS.
This can only be changed if the value … | column | TmnxBITSIfType | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.13 |
| tSyncIfTimingAdmRef2SrcHw obsolete The value of tSyncIfTimingAdmRef2SrcHw specifies the source HW Index
of the second timing reference if the source is not a port.
This can only be set to a valid HW … | column | TmnxHwIndexOrZero | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.14 |
| tSyncIfTimingAdmRef2BITSIfType obsolete The value of tSyncIfTimingAdmRef2BITSIfType specifies the interface
type of the second timing reference if the source is BITS.
This can only be changed if the value… | column | TmnxBITSIfType | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.15 |
| tSyncIfTimingAdmBITSOutAdmStatus The value of tSyncIfTimingAdmBITSOutAdmStatus specifies administrative
status of the BITS (Building Integrated Timing Supply) output timing
reference.
In an XRS-40 … | column | TmnxPortAdminStatus | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.16 |
| tSyncIfTimingAdmBITSOutLineLen tSyncIfTimingAdmBITSOutLineLen specifies the length of the line
(in feet) for the BITS (Building Integrated Timing Supply) output.
The following values are valid:
lengthNotApp… | column | Enumeration | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.17 |
| tSyncIfTimingAdmRef1CfgQltyLevel The value of tSyncIfTimingAdmRef1CfgQltyLevel specifies the configured
Quality Level of Reference 1. A value of 'unknown (0)' indicates
Reference 1 is not forced to a specific qua… | column | TmnxSSMQualityLevel | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.18 |
| tSyncIfTimingAdmRef2CfgQltyLevel The value of tSyncIfTimingAdmRef2CfgQltyLevel specifies the configured
Quality Level of Reference 2. A value of 'unknown (0)' indicates
Reference 2 is not forced to a specific qua… | column | TmnxSSMQualityLevel | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.19 |
| tSyncIfTimingAdmRefOrder1 The value of tSyncIfTimingAdmRefOrder1 specifies the most preferred
timing reference source.
The synchronous equipment timing subsystem chooses a timing reference
b… | column | TmnxSETSRefSource | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.2 |
| tSyncIfTimingAdmBITSCfgQltyLevel The value of tSyncIfTimingAdmBITSCfgQltyLevel specifies the configured
Quality Level of the BITS interface. A value of 'unknown (0)'
indicates the BITS interface is not forced to … | column | TmnxSSMQualityLevel | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.20 |
| tSyncIfTimingAdmRef1NationalUse obsolete The value of tSyncIfTimingAdmRef1NationalUse specifies the national
use bit to carry SSM Messages. This applies only to E1 BITS
interfaces.
This object was obsolete… | column | Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.21 |
| tSyncIfTimingAdmRef2NationalUse obsolete The value of tSyncIfTimingAdmRef2NationalUse specifies the national
use bit to carry SSM Messages. This applies only to E1 BITS
interfaces.
This object was obsolete… | column | Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.22 |
| tSyncIfTimingAdmBITSNationalUse The value of tSyncIfTimingAdmBITSNationalUse specifies the national
use bit to carry SSM Messages. This applies only to E1 BITS
interfaces. | column | Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.23 |
| tSyncIfTimingAdmQLSelection The value of tSyncIfTimingAdmQLSelection specifies whether or not the
timing reference selection process uses the quality level of each
timing reference when making the decision o… | column | TIMETRA-TC-MIBTmnxEnabledDisabled | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.24 |
| tSyncIfTimingAdmRefOrder4 The value of tSyncIfTimingAdmRefOrder4 specifies the fourth most
preferred timing reference for the synchronous equipment timing
subsystem. | column | TmnxSETSRefSource | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.25 |
| tSyncIfTimingAdmPTPAdminStatus The value of tSyncIfTimingAdmPTPAdminStatus specifies the desired
administrative status of the Precision Timing Protocol (PTP) timing
reference. | column | TmnxPortAdminStatus | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.26 |
| tSyncIfTimingAdmPTPCfgQltyLevel The value of tSyncIfTimingAdmPTPCfgQltyLevel specifies the configured
Quality Level of the Precision Timing Protocol (PTP). A value of
'unknown (0)' specifies PTP is not forced to… | column | TmnxSSMQualityLevel | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.27 |
| tSyncIfTimingAdmBITSOutQlMin The value of tSyncIfTimingAdmBITSOutQlMin specifies the minimum
quality level that a signal must have for it to be selected for BITS
output. This can be used to ensure that the si… | column | TmnxSSMQualityLevel | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.29 |
| tSyncIfTimingAdmRefOrder2 The value of tSyncIfTimingAdmRefOrder2 specifies the second most
preferred timing reference for the synchronous equipment timing
subsystem. | column | TmnxSETSRefSource | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.3 |
| tSyncIfTimingAdmBITSOutSquelch The value of tSyncIfTimingAdmBITSOutSquelch specifies whether or not
to squelch the output signal. This object is only valid when there is
no valid reference selected.
… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.30 |
| tSyncIfTimingAdmQlMin The value of tSyncIfTimingAdmQlMin specifies the minimum acceptable
quality level that a signal must have for it to be considered for
selection by the system timing module.
… | column | TmnxSSMQualityLevel | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.32 |
| tSyncIfTimingAdmWaitToRestorTime The value of tSyncIfTimingAdmWaitToRestorTime specifies the time, in
minutes, that a previously failed input reference must be valid before
it will be used for either the BITS out… | column | minutes Unsigned32 | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.33 |
| tSyncIfTimingAdmChangedMask The value of tSyncIfTimingAdmChangedMask indicates a bitmask of which
synchronous interface timing objects have been set, but not committed.
The agent sets these bi… | column | Bits | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.34 |
| tSyncIfTimingAdmSyncECfgQltyLevl The value of tSyncIfTimingAdmSyncECfgQltyLevl specifies the configured
Quality Level of the Synchronous Ethernet (SyncE) timing reference. A
value of 'unknown (0)' specifies SyncE… | column | TmnxSSMQualityLevel | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.35 |
| tSyncIfTimingAdmSyncEAdminStatus The value of tSyncIfTimingAdmSyncEAdminStatus specifies the desired
administrative status of the Synchronous Ethernet (SyncE) timing
reference. | column | TmnxPortAdminStatus | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.36 |
| tSyncIfTimingAdmRefOrder5 The value of tSyncIfTimingAdmRefOrder5 specifies the fifth most
preferred timing reference for the synchronous equipment timing
subsystem. | column | TmnxSETSRefSource | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.37 |
| tSyncIfTimingAdmGnssCfgQltyLevel The value of tSyncIfTimingAdmGnssCfgQltyLevel specifies the configured
Quality Level of the GNSS (Global Navigation Satellite System) timing
reference. A value of 'unknown (0)' sp… | column | TmnxSSMQualityLevel | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.38 |
| tSyncIfTimingAdmGnssAdminStatus The value of tSyncIfTimingAdmGnssAdminStatus specifies the desired
administrative status of the GNSS (Global Navigation Satellite System)
timing reference. | column | TmnxPortAdminStatus | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.39 |
| tSyncIfTimingAdmRef1SrcPort The value of tSyncIfTimingAdmRef1SrcPort specifies the source port of
the first timing reference. | column | TIMETRA-TC-MIBTmnxPortID | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.4 |
| tSyncIfTimingAdmRef1AdminStatus The value of tSyncIfTimingAdmRef1AdminStatus specifies the desired
administrative status of the first timing reference. | column | TmnxPortAdminStatus | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.5 |
| tSyncIfTimingAdmRef2SrcPort The value of tSyncIfTimingAdmRef2SrcPort specifies the source port of
the second timing reference. | column | TIMETRA-TC-MIBTmnxPortID | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.6 |
| tSyncIfTimingAdmRef2AdminStatus The value of tSyncIfTimingAdmRef2AdminStatus specifies the desired
administrative status of the second timing reference. | column | TmnxPortAdminStatus | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.7 |
| tSyncIfTimingAdmChanged The value of tSyncIfTimingAdmChanged is a bitmask that indicates which
objects have been set, but not committed. bit values used here are:
0x0001: tSyncIfTiming… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.8 |
| tSyncIfTimingAdmRefOrder3 The value of tSyncIfTimingAdmRefOrder3 specifies the third most
preferred timing reference for the synchronous equipment timing
subsystem. | column | TmnxSETSRefSource | .1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.9 |