s5AgSysSpanningTreeAdminCompatibility
S5-AGENT-MIB ·
.1.3.6.1.4.1.45.1.6.4.4.24
Object
scalar
r/w
Bits
This object controls the compatibility mode for various
features. Note that for some features, the actual operational
mode might not change until after a system reset.
The port802dot1dLearning(0) bit indicates whether the learning
mode of a port stays in the Forwarding state, or changes to the
Disabled state when the port's operational status goes down. If
the bit is on, it means the port goes to the Disabled state. If
the bit is off, it means the port stays in the Forwarding state.
Context
- MIB
- S5-AGENT-MIB
- OID
.1.3.6.1.4.1.45.1.6.4.4.24- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- s5AgentSystem
- Siblings
- 67
Syntax
Bits
Values & Constraints
Enumerated Values
0 | port802dot1dLearning |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| s5AgSysAutoPvid This value indicates whether adding a port as a member
of a VLAN automatically results in its PVID being set
to be the same as that VLAN ID. Some exceptions apply. | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.1 |
| s5AgSysCpuIpAddress The system's CPU IP address. Note that for a stackable
system in standalone mode, this will be the standalone
IP address, but in stack mode, this will be the stack IP
address. I… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.45.1.6.4.4.10 |
| s5AgSysStackIpAddress The stack IP address of a stackable system. A non-stackable
system should never return an instance of this object, nor allow
writes to this object. Note that in standalone mode,… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.45.1.6.4.4.11 |
| s5AgSysCpuNetMask The system's CPU subnet mask. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.45.1.6.4.4.12 |
| s5AgSysManagementVlanId The VLAN ID of the system's management VLAN. | scalar | Integer32 | .1.3.6.1.4.1.45.1.6.4.4.13 |
| s5AgSysBinaryConfigUnitNumber When in standalone mode, and loading a binary configuration file
that was created from a stack, this object specifies the unit
number of the portion of the config file to be extra… | scalar | Integer32 | .1.3.6.1.4.1.45.1.6.4.4.14 |
| s5AgSysStackInsertionUnitNumber When in stack mode, this object specifies the unit number to
be assigned to the next unit that joins the stack. The value
may not be set to the unit number of an existing stack m… | scalar | Integer32 | .1.3.6.1.4.1.45.1.6.4.4.15 |
| s5AgSysSpanningTreeOperMode This object indicates the current spanning-tree mode of the system.
The meaning of specific values is:
avayaStpg(1) .. The older proprietary mode which supports
… | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.16 |
| s5AgSysSpanningTreeAdminMode This object indicates the desired spanning-tree mode of the system.
The meaning of specific values is:
avayaStpg(1) .. The older proprietary mode which supports
… | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.17 |
| s5AgSysAutoUnitReplacementEnabled This object indicates whether the auto-unit-replacement feature
is enabled or disabled. The value when retrieved will always be
true(1) or false(2). Setting the value to setToDe… | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.18 |
| s5AgSysAsciiConfigManualUpload deprecated Indicates the status of the last manual attempt to
upload an ASCII configuration file. The value of
this object when retrieved can be either passed(1),
inProgress(2) or failed(3)… | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.19 |
| s5AgSysCurrentOperationalMode Indicates the stacking mode. Pure stack mode does not
allow BS450 and BS410 units to join stack and provides
some advanced features that are not available in Hybrid
stack mode. | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.2 |
| s5AgSysSpanningTreePathCostCalculationMode This object indicates the current spanning-tree path cost
calculation mode of the system. Note that this object can
only take the value ieee802dot1dCompatible(1) if the value of
… | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.20 |
| s5AgSysUsbTargetUnit This object indicates the unit number of the USB port to be
use in file upload/download operations. | scalar | Integer32 | .1.3.6.1.4.1.45.1.6.4.4.21 |
| s5AgSysSpanningTreePortMode This object indicates the current spanning-tree port mode. | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.22 |
| s5AgSysLicenseFilename Name of the license file that will be downloaded/uploaded
when the s5AgInfoFileAction object is set to dnldLicense(18),
upldLicense(19), dlndLicenseFromUsb(20), upldLicense(21), o… | scalar | OctetString | .1.3.6.1.4.1.45.1.6.4.4.23 |
| s5AgSysSpanningTreeOperCompatibility This object indicates the operational compatibility mode for
various features controlled by the associated object,
s5AgSysSpanningTreeAdminCompatibility. | scalar | Bits | .1.3.6.1.4.1.45.1.6.4.4.25 |
| s5AgSysGlobalFlowControlEnabled This object controls whether flow control for ethernet ports
is globally enabled or disabled. This object is only used
on systems for which flow control cannot be enabled/disable… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.1.6.4.4.26 |
| s5AgSysAutosaveToNvramEnabled This object controls whether autosaving to NVRAM is enabled.
Autosaving normally occurs periodically in a background task
if any configuration changes have been made. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.1.6.4.4.27 |
| s5AgSysFlushMacAddrTableAll Setting this object to flush(1) will flush the CDT MAC address
table. Setting it to dynamic(2) will flush only dynamically
learned addresses. Setting it to static(3) will flush … | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.28 |
| s5AgSysFlushMacAddrTableByPortList Setting this object will flush the CDT MAC address for all
ports specified in the value. On retrieval, the value is
the last value set, or a zero-length octet string if it has
ne… | scalar | Q-BRIDGE-MIBPortList | .1.3.6.1.4.1.45.1.6.4.4.29 |
| s5AgSysNextBootOperationalMode Indicates the stacking mode at the next boot. A change
to this object will modify the stacking mode after the
system is reset/rebooted. | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.3 |
| s5AgSysFlushMacAddrTableByVlan Setting this object will flush the CDT MAC address table for
the specified VLAN. On retrieval, the value is the last
value set, or 1 if it has never been set. | scalar | Q-BRIDGE-MIBVlanId | .1.3.6.1.4.1.45.1.6.4.4.30 |
| s5AgSysFlushMacAddrTableByTrunk Setting this object will flush the CDT MAC address table for
the specified trunk. On retrieval, the value is the last
value set, or 1 if it has never been set. | scalar | Integer32 | .1.3.6.1.4.1.45.1.6.4.4.31 |
| s5AgSysFlushMacAddrTableByAddress Setting this object will flush the specified MAC address
from the CDT MAC address table. On retrieval, its value is
the last value set, or 00:00:00:00:00:00 if it has never
been … | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.45.1.6.4.4.32 |
| s5AgSysVlanConfigControl This object controls the VLAN configuration control mode:
automatic - AutoPVID and automatic change to membership
of port-based VLANs
autopvid -- Automatic change to P… | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.33 |
| s5AgSysJumboFramesEnabled This object controls whether jumbo frames are supported. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.1.6.4.4.34 |
| s5AgSysAutoUnitReplacementSaveEnabled This object indicates whether auto-unit-replacement automatic
saving of unit images to the base unit is enabled. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.1.6.4.4.35 |
| s5AgSysAutoUnitReplacementRestore This object is used to force the configuration of a unit to be
restored from the saved configuration on the base unit. Setting
the value to a unit number will force the configura… | scalar | Integer32 | .1.3.6.1.4.1.45.1.6.4.4.36 |
| s5AgSysAutoUnitReplacementForceSave This object is used to force the configuration of a non-base
unit to be saved to the base unit. Setting it to a particular
unit number will force the save of that unit's configur… | scalar | Integer32 | .1.3.6.1.4.1.45.1.6.4.4.37 |
| s5AgSysTftpServerInetAddressType This object indicates the type of address stored in the related
object s5AgSysTftpServerInetAddress. | scalar | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.45.1.6.4.4.38 |
| s5AgSysTftpServerInetAddress This object contains the IP address of the TFTP server for all
TFTP operations. | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.45.1.6.4.4.39 |
| s5AgSysBinaryConfigFilename Name of the binary configuration file that will be
downloaded/uploaded when the s5AgInfoFileAction object is
set to dnldConfig(2), upldConfig(4), dlndConfigFromUsb(16),
or upldCon… | scalar | OctetString | .1.3.6.1.4.1.45.1.6.4.4.4 |
| s5AgSysTelnetSessionLoginAuthenType This object controls the authentication method used for telnet
session logins. The values of this object have the following meanings:
none(1) ---- No username/password is req… | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.40 |
| s5AgSysSerialConsoleLoginAuthenType This object controls the authentication method used for serial
console logins. The values of this object have the following meanings:
none(1) ---- No username/password is req… | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.41 |
| s5AgSysSshAuthKeyFilename Name of the Ssh authentication key file that will be downloaded
when the s5AgInfoFileAction object is set to dnldSshDsaAuthKeyFromUsb(23),
dnldSshRsaAuthKeyFromUsb(28), dnldSshDs… | scalar | OctetString | .1.3.6.1.4.1.45.1.6.4.4.42 |
| s5AgSysAsciiConfigManualUploadApplications This objects is used to specify the set of applications to
be included an an ASCII configure file when it is uploaded. | scalar | Bits | .1.3.6.1.4.1.45.1.6.4.4.43 |
| s5AgSysOperationalLicense The type of license currently in effect. | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.44 |
| s5AgSysInstalledLicense The type of license currently installed. | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.45 |
| s5AgSysCpuIpv6Address The system's CPU IPv6 address. Note that for a stackable
system in standalone mode, this will be the standalone
IPv6 address, but in stack mode, this will be the stack IPv6
addre… | scalar | IPV6-TCIpv6Address | .1.3.6.1.4.1.45.1.6.4.4.46 |
| s5AgSysStackIpv6Address The stack IPv6 address of a stackable system. A non-stackable
system should never return an instance of this object, nor allow
writes to this object. Note that in standalone mod… | scalar | IPV6-TCIpv6Address | .1.3.6.1.4.1.45.1.6.4.4.47 |
| s5AgSysCpuIpv6NetMask The system's CPU IPv6 subnet mask. | scalar | IPV6-TCIpv6AddressPrefix | .1.3.6.1.4.1.45.1.6.4.4.48 |
| s5AgSysStackIpv6NetMask The system's CPU IPv6 subnet mask. | scalar | IPV6-TCIpv6AddressPrefix | .1.3.6.1.4.1.45.1.6.4.4.49 |
| s5AgSysTftpServerAddress The IP address of the TFTP server for all TFTP operations.
If not used, then the value is 0.0.0.0. Further, if the
value of s5AgTftpServerInetAddressType is not ipv4(1), then
the… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.45.1.6.4.4.5 |
| s5AgSysIpv6DefaultGateway The system's IPv6 default gateway. | scalar | IPV6-TCIpv6Address | .1.3.6.1.4.1.45.1.6.4.4.50 |
| s5AgSysSpanningTreeBpduFilterIgnoreSelf This object indicates if bridge's own BPDUs
should be ignored or not when BPDU FIltering
decisions are made. If the value is set to true,
bridge's own BPDUs are ignored by BPDU FI… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.1.6.4.4.51 |
| s5AgSysIdentifyUnits This object is used to tell a stackable system to identify
the numbering of units in the stack by flashing the appropriate
number of LEDs on the front panel of each unit. | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.52 |
| s5AgSysMacAddrTableLearningPorts This object controls the list of ports on which MAC address
learning is enabled. | scalar | Q-BRIDGE-MIBPortList | .1.3.6.1.4.1.45.1.6.4.4.53 |
| s5AgSysSerialSecurityEnable This object enables/disables the serial security feature. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.1.6.4.4.54 |
| s5AgSysMgmtStackIpAddress The management stack IP address of a stackable system. This
address applies to the out-of-band, dedicated management ports.
Its counterpart for in-band access (management VLAN) is… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.45.1.6.4.4.55 |
| s5AgSysAuditEnable This object enables/disables CLI audit logging. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.1.6.4.4.56 |
| s5AgSysQuickConfigEnable This object enables/disables quick config. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.1.6.4.4.57 |
| s5AgSysStackIpv6MgmtAddress The stack IP address of a stackable system. A non-stackable
system should never return an instance of this object, nor allow
writes to this object. Note that in standalone mode,… | scalar | IPV6-TCIpv6Address | .1.3.6.1.4.1.45.1.6.4.4.58 |
| s5AgSysStackIpv6MgmtNetMask The stack IP address of a stackable system. A non-stackable
system should never return an instance of this object, nor allow
writes to this object. Note that in standalone mode,… | scalar | IPV6-TCIpv6AddressPrefix | .1.3.6.1.4.1.45.1.6.4.4.59 |
| s5AgSysAsciiConfigFilename deprecated Name of the ascii configuration file that will be
downloaded/uploaded either at boot time when the
s5AgSysAsciiConfigAutoDownload object is set to
useConfig(3), or when the s5AgSy… | scalar | OctetString | .1.3.6.1.4.1.45.1.6.4.4.6 |
| s5AgSysIpv6MgmtGateway The IP address of the default gateway associated with the
physical dedicated management port (out of band management port)
of a component. | scalar | IPV6-TCIpv6Address | .1.3.6.1.4.1.45.1.6.4.4.60 |
| s5AgSysBlinkLeds This object is used to start or stop the flashing of LEDs
from the front panel of a unit. When setting the object,
s5AgSysBlinkLedsUnit specifies the unit number and
s5AgSysBlink… | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.61 |
| s5AgSysBlinkLedsUnit This object specifies the unit number used in the blink-leds action. | scalar | Integer32 | .1.3.6.1.4.1.45.1.6.4.4.62 |
| s5AgSysBlinkLedsTimeThreshold This object specifies the time threshold used in the blink-leds action. | scalar | Minutes Integer32 | .1.3.6.1.4.1.45.1.6.4.4.63 |
| s5AgSysJumboFramesSize This object represents the maximum Ethernet frame size to be used when
jumbo frames are supported & enabled ( see s5AgSysJumboFramesEnabled ). Default settings
for jumbo should be… | scalar | Bytes Integer32 | .1.3.6.1.4.1.45.1.6.4.4.64 |
| s5AgSysDiagnosticsQuickModeEnabled This object controls diagnostics tests mode at boot sequence. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.1.6.4.4.65 |
| s5AgSysTimeStampEnabled This object indicates whether the UTC stamp is displayed in 'show *' output or not.
A TRUE(1) value means that the time stamp is displayed, a FALSE(2) value indicates that time s… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.1.6.4.4.66 |
| s5AgSysForcedStackModeEnabled This object indicates whether the Forced Stack Mode feature is enabled. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.1.6.4.4.67 |
| s5AgSysSflowGlobalEnable This object globally enables or disables sflow. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.45.1.6.4.4.68 |
| s5AgSysAsciiConfigAutoDownload deprecated Indicates whether an ASCII configuration file should be
downloaded at boot time. The file can be downloaded
using either the configured filename and TFTP server
address, or a BOO… | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.7 |
| s5AgSysAsciiConfigAutoDldStatus deprecated Indicates the status of the last automatic ASCII
configuration file download at boot time. If no
automatic download at boot time has been attempted,
the value returned will be fa… | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.8 |
| s5AgSysAsciiConfigManualDownload deprecated Indicates the status of the last manual attempt to
download an ASCII configuration file. The value of
this object when retrieved can be either passed(1),
inProgress(2) or failed(… | scalar | Enumeration | .1.3.6.1.4.1.45.1.6.4.4.9 |