pktcSigDevVmwiSigProtocol
PKTC-IETF-SIG-MIB ·
.1.3.6.1.2.1.169.1.1.37
Object
scalar
r/w
PktcSubscriberSideSigProtocol
This object identifies the subscriber line protocol used
for signaling the information on Visual Message Waiting
Indicator (VMWI). Different countries define different
VMWI signaling protocols to support VMWI service.
Frequency shift keying (FSK) is most commonly used.
DTMF is an alternative.
The value of this MIB object MUST NOT persist across MTA
reboots.
Context
- MIB
- PKTC-IETF-SIG-MIB
- OID
.1.3.6.1.2.1.169.1.1.37- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- pktcSigDevObjects
- Siblings
- 40
Syntax
PktcSubscriberSideSigProtocol
- Source
- PktcSubscriberSideSigProtocol
- Base type
Enumeration
Values & Constraints
Type Values
1 | fsk |
2 | dtmf |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| pktcSigDevCodecTable This table describes the MTA-supported codec types. An MTA
MUST populate this table with all possible combinations of
codecs it supports for simultaneous operation. For example,… | table | - | .1.3.6.1.2.1.169.1.1.1 |
| pktcSigDevR5Cadence This object specifies ring cadence 5 (a user-defined
field).
The value of this MIB object MUST NOT persist across MTA
reboots. | scalar | PktcRingCadence | .1.3.6.1.2.1.169.1.1.10 |
| pktcSigDevR6Cadence This object specifies ring cadence 6 (a user-defined
field).
The value of this MIB object MUST NOT persist across MTA
reboots. | scalar | PktcRingCadence | .1.3.6.1.2.1.169.1.1.11 |
| pktcSigDevR7Cadence This object specifies ring cadence 7 (a user-defined
field).
The value of this MIB object MUST NOT persist across MTA
reboots. | scalar | PktcRingCadence | .1.3.6.1.2.1.169.1.1.12 |
| pktcSigDevRgCadence This object specifies ring cadence rg (a user-defined
field).
The value of this MIB object MUST NOT persist across MTA
reboots. | scalar | PktcRingCadence | .1.3.6.1.2.1.169.1.1.13 |
| pktcSigDevRsCadence This object specifies ring cadence rs (a user-defined
field). The MTA MUST reject any attempt to make this object
repeatable.
The value of this MIB object MUST NOT per… | scalar | PktcRingCadence | .1.3.6.1.2.1.169.1.1.14 |
| pktcSigDefCallSigDscp The default value used in the IP header for setting the
Differentiated Services Code Point (DSCP) value for call
signaling.
The value of this MIB object MUST NOT persis… | scalar | Dscp | .1.3.6.1.2.1.169.1.1.15 |
| pktcSigDefMediaStreamDscp This object contains the default value used in the IP
header for setting the Differentiated Services Code Point
(DSCP) value for media stream packets. The MTA MUST NOT
update thi… | scalar | Dscp | .1.3.6.1.2.1.169.1.1.16 |
| pktcSigCapabilityTable This table describes the signaling types supported by this
MTA. | table | - | .1.3.6.1.2.1.169.1.1.17 |
| pktcSigDefNcsReceiveUdpPort This object contains the MTA User Datagram Protocol (UDP)
receive port that is being used for NCS call signaling.
This object should only be changed by the configuration
file.
… | scalar | Unsigned32 | .1.3.6.1.2.1.169.1.1.18 |
| pktcSigPowerRingFrequency This object must only be provided via the configuration
file during the provisioning process. The power ring
frequency is the frequency at which the sinusoidal voltage
must trave… | scalar | Enumeration | .1.3.6.1.2.1.169.1.1.19 |
| pktcSigDevEchoCancellation This object specifies if the device is capable of echo
cancellation. The MTA MUST set this MIB object to a
value of true(1) if it is capable of echo
cancellation, and a value of … | scalar | SNMPv2-TCTruthValue | .1.3.6.1.2.1.169.1.1.2 |
| pktcSigPulseSignalTable The Pulse signal table defines the pulse signal operation.
There are nine types of international pulse signals,
with each signal having a set of provisionable parameters.
The valu… | table | - | .1.3.6.1.2.1.169.1.1.20 |
| pktcSigDevCidMode For on-hook caller id, pktcSigDevCidMode selects the method
for representing and signaling caller identification. For
the duringRingingETS method, the Frequency Shift Keying
(FSK… | scalar | Enumeration | .1.3.6.1.2.1.169.1.1.21 |
| pktcSigDevCidAfterRing This object specifies the delay between the end of first
ringing pattern and the start of the transmission of the
FSK or DTMF containing the caller id information. It is
only use… | scalar | Milliseconds Unsigned32 | .1.3.6.1.2.1.169.1.1.22 |
| pktcSigDevCidAfterDTAS This object specifies the delay between the end of the
Dual Tone Alert Signal (DT-AS) and the start of the
transmission of the FSK or DTMF containing the caller id
information. T… | scalar | Milliseconds Unsigned32 | .1.3.6.1.2.1.169.1.1.23 |
| pktcSigDevCidAfterRPAS This object specifies the delay between the end of the
Ring Pulse Alert Signal (RP-AS) and the start of the
transmission of the FSK or DTMF containing the caller id
information. … | scalar | Milliseconds Unsigned32 | .1.3.6.1.2.1.169.1.1.24 |
| pktcSigDevRingAfterCID This object specifies the delay between the end of the
complete transmission of the FSK or DTMF containing the
caller id information and the start of the first ring
pattern. It i… | scalar | Milliseconds Unsigned32 | .1.3.6.1.2.1.169.1.1.25 |
| pktcSigDevCidDTASAfterLR This object specifies the delay between the end of the
Line Reversal and the start of the Dual Tone Alert Signal
(DT-AS). This object is only used when pktcSigDevCidMode
is set t… | scalar | Milliseconds Unsigned32 | .1.3.6.1.2.1.169.1.1.26 |
| pktcSigDevVmwiMode For visual message waiting indicator (VMWI),
pktcSigDevVmwiMode selects the alerting signal method. For
the dtAsETS, rpAsETS, lrAsETS, osi, and lrETS methods,
the FSK containing … | scalar | Enumeration | .1.3.6.1.2.1.169.1.1.27 |
| pktcSigDevVmwiAfterDTAS This object specifies the delay between the end of the
Dual Tone Alert Signal (DT-AS) and the start of the
transmission of the FSK or DTMF containing the VMWI
information.
… | scalar | Milliseconds Unsigned32 | .1.3.6.1.2.1.169.1.1.28 |
| pktcSigDevVmwiAfterRPAS This object specifies the delay between the end of the
Ring Pulse Alert Signal (RP-AS) and the start of the
transmission of the FSK or DTMF containing the VMWI
information.
… | scalar | Milliseconds Unsigned32 | .1.3.6.1.2.1.169.1.1.29 |
| pktcSigDevSilenceSuppression This object specifies if the device is capable of
silence suppression (as a result of Voice Activity
Detection). The MTA MUST set this MIB object to a
value of true(1) if it is c… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.2.1.169.1.1.3 |
| pktcSigDevVmwiDTASAfterLR This object specifies the delay between the end of the
Line Reversal and the start of the Dual Tone Alert Signal
(DT-AS) for VMWI information. This object is only used
when pktcS… | scalar | Milliseconds Unsigned32 | .1.3.6.1.2.1.169.1.1.30 |
| pktcSigDevRingCadenceTable Cadence rings are defined by the telco governing
body for each country. The MTA must be able to support
various ranges of cadence patterns and cadence periods.
The MTA will be ab… | table | - | .1.3.6.1.2.1.169.1.1.31 |
| pktcSigDevToneTable The Tone Table defines the composition of tones and
various tone operations.
The definition of the tones callWaiting1 through
callWaiting4 in this table MUST only conta… | table | - | .1.3.6.1.2.1.169.1.1.32 |
| pktcSigDevMultiFreqToneTable This MIB table defines the characteristics of tones
with multiple frequencies. The constraints imposed
on the tones by the MIB table pktcSigDevToneTable
need to be considered for… | table | - | .1.3.6.1.2.1.169.1.1.33 |
| pktcSigDevCidDelayAfterLR This object specifies the delay between the end of the
Line Reversal and the start of the FSK or DTMF signal.
This MIB object is used only when pktcSigDevCidMode is
set to a value… | scalar | Milliseconds Unsigned32 | .1.3.6.1.2.1.169.1.1.34 |
| pktcSigDevCidDtmfStartCode This object identifies optional start codes used when
the MIB object pktcSigDevCidSigProtocol is set
to a value of 'dtmf(2)'.
Different countries define different calle… | scalar | DtmfCode | .1.3.6.1.2.1.169.1.1.35 |
| pktcSigDevCidDtmfEndCode This object identifies optional end codes used when the
pktcSigDevCidSigProtocol is set to a value of
'dtmf(2)'.
Different countries define different caller id signalin… | scalar | DtmfCode | .1.3.6.1.2.1.169.1.1.36 |
| pktcSigDevVmwiDelayAfterLR This object specifies the delay between the end of the
Line Reversal and the start of the FSK or DTMF signal.
This object is only used when pktcSigDevVmwiMode is
set to a value of… | scalar | Milliseconds Unsigned32 | .1.3.6.1.2.1.169.1.1.38 |
| pktcSigDevVmwiDtmfStartCode This object identifies optional start codes used when
the pktcSigDevVmwiSigProtocol is set to a value of
'dtmf(2)'. Different countries define different On Hook
Data Transmission… | scalar | DtmfCode | .1.3.6.1.2.1.169.1.1.39 |
| pktcSigDevCidSigProtocol This object is used to configure the subscriber-line
protocol used for signaling on-hook caller id information.
Different countries define different caller id signaling
protocols … | scalar | PktcSubscriberSideSigProtocol | .1.3.6.1.2.1.169.1.1.4 |
| pktcSigDevVmwiDtmfEndCode This object identifies an optional end code used when the
pktcSigDevVmwiSigProtocol is set to a value of
'dtmf(2)'. Different countries define different on-hook
Data Transmission… | scalar | DtmfCode | .1.3.6.1.2.1.169.1.1.40 |
| pktcSigDevrpAsDtsDuration This object specifies the duration of the rpASDTS ring
pulse prior to the start of the transmission of the
FSK or DTMF containing the caller id information. It is
only used when … | scalar | Milliseconds Unsigned32 | .1.3.6.1.2.1.169.1.1.41 |
| pktcSigDevR0Cadence This object specifies ring cadence 0 (a user-defined
field).
The value of this MIB object MUST NOT persist across MTA
reboots. | scalar | PktcRingCadence | .1.3.6.1.2.1.169.1.1.5 |
| pktcSigDevR1Cadence This object specifies ring cadence 1 (a user-defined
field).
The value of this MIB object MUST NOT persist across MTA
reboots. | scalar | PktcRingCadence | .1.3.6.1.2.1.169.1.1.6 |
| pktcSigDevR2Cadence This object specifies ring cadence 2 (a user-defined
field).
The value of this MIB object MUST NOT persist across MTA
reboots. | scalar | PktcRingCadence | .1.3.6.1.2.1.169.1.1.7 |
| pktcSigDevR3Cadence This object specifies ring cadence 3 (a user-defined
field).
The value of this MIB object MUST NOT persist across MTA
reboots. | scalar | PktcRingCadence | .1.3.6.1.2.1.169.1.1.8 |
| pktcSigDevR4Cadence This object specifies ring cadence 4 (a user-defined
field).
The value of this MIB object MUST NOT persist across MTA
reboots. | scalar | PktcRingCadence | .1.3.6.1.2.1.169.1.1.9 |