agentPortMulticastControlThresholdUnit
NG700-SWITCHING-MIB ·
.1.3.6.1.4.1.4526.11.1.2.13.1.27
Object
column
r/w
Enumeration
Configures the units of the threshold value to percentage of port speed or absolute packets per second.
Context
- MIB
- NG700-SWITCHING-MIB
- OID
.1.3.6.1.4.1.4526.11.1.2.13.1.27- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- agentPortConfigEntry
- Table
- agentPortConfigTable
- Siblings
- 35
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| agentPortDot1dBasePort The port number of this port. | column | Integer32 | .1.3.6.1.4.1.4526.11.1.2.13.1.1 |
| agentPortClearStats clear stats for this port only | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.10 |
| agentPortDefaultType This object identifies the default administrative port type,
to be used in conjunction with the operational port type
denoted by agentPortType.
This object represen… | column | ObjectIdentifier | .1.3.6.1.4.1.4526.11.1.2.13.1.11 |
| agentPortType This object identifies the port type. An initial set of MAU types
are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to
new types of MAUs is managed by the IANA. If … | column | ObjectIdentifier | .1.3.6.1.4.1.4526.11.1.2.13.1.12 |
| agentPortAutoNegAdminStatus This object identifies the administration status of auto negotiation
for this port. | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.13 |
| agentPortDot3FlowControlMode Config flowcontrol allows you to enable or disable
802.3x flow control for this port. This value
applies to only full-duplex mode ports. Enabling
symmetric flow control allows the… | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.14 |
| agentPortMaxFrameSizeLimit This object identifies the largest value that can be
configured for agentPortMaxFrameSize | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4526.11.1.2.13.1.18 |
| agentPortMaxFrameSize This object identifies the currently configured maximum frame size
value for this port. The maximmum value that this object can be set
to is the value of agentPortMaxFrameSizeLimi… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4526.11.1.2.13.1.19 |
| agentPortIfIndex The switch's Port IfIndex | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4526.11.1.2.13.1.2 |
| agentPortBroadcastControlMode If enabled, broadcast storm recovery will function on this port.
When you specify Enable for Broadcast Storm Recovery and the broadcast
traffic on this Ethernet port exceeds the c… | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.20 |
| agentPortBroadcastControlThreshold Configures the broadcast storm recovery threshold for this port
as a percentage of port speed or as an absolute pps rate. | column | Integer32 | .1.3.6.1.4.1.4526.11.1.2.13.1.21 |
| agentPortMulticastControlMode If enabled, multicast storm recovery will function on this port.
When you specify Enable for Multicast Storm Recovery and the multicast
traffic on this Ethernet port exceeds the c… | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.22 |
| agentPortMulticastControlThreshold Configures the multicast storm recovery threshold for this port
as a percentage of port speed or as an absolute pps rate. | column | Integer32 | .1.3.6.1.4.1.4526.11.1.2.13.1.23 |
| agentPortUnicastControlMode If enabled, unicast storm recovery will function on this port.
When you specify Enable for Unicast Storm Recovery and the unknown unicast
traffic on this Ethernet port exceeds the… | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.24 |
| agentPortUnicastControlThreshold Configures the unicast storm recovery threshold for this port
as a percentage of port speed or as an absolute pps rate. | column | Integer32 | .1.3.6.1.4.1.4526.11.1.2.13.1.25 |
| agentPortBroadcastControlThresholdUnit Configures the units of the threshold value to percentage of
port speed or absolute packets per second. | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.26 |
| agentPortUnicastControlThresholdUnit Configures the units of the threshold value to percentage of
port speed or absolute packets per second. | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.28 |
| agentPortVoiceVlanMode Describes and Configures the Port Voice VLAN Mode. This object
can only be set to disable(5). | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.29 |
| agentPortIanaType The switch's Port Type | column | IANAifType-MIBIANAifType | .1.3.6.1.4.1.4526.11.1.2.13.1.3 |
| agentPortVoiceVlanID Describes and Configures the Port Voice VLAN ID
if the Voice Vlan Mode is Vlan ID. | column | Integer32 | .1.3.6.1.4.1.4526.11.1.2.13.1.30 |
| agentPortVoiceVlanPriority Describes and Configures the Port Voice VLAN Priority
if the Voice Vlan Mode is dot1p. A value of 255 indicates
that the priority is not configured. | column | Integer32 | .1.3.6.1.4.1.4526.11.1.2.13.1.31 |
| agentPortVoiceVlanDataPriorityMode Describes and Configures the Port Voice VLAN Data Priority Mode. | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.32 |
| agentPortVoiceVlanOperationalStatus Describes the Port Voice VLAN Operational Status. | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.33 |
| agentPortVoiceVlanUntagged Describes and Configures the Port Voice VLAN tagging mode. | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.34 |
| agentPortVoiceVlanNoneMode Describes and Configures the Port Voice VLAN None mode. | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.35 |
| agentPortVoiceVlanDSCP Describes and Configures the Port Voice VLAN DSCP value. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4526.11.1.2.13.1.36 |
| agentPortVoiceVlanAuthMode Describes and Configures the Port Voice VLAN Authentication mode.
Disable means authentication not required for voice devices when dot1x is enabled. | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.37 |
| agentPortDot3FlowControlOperStatus This object identifies operational status of the flow control per port. | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.38 |
| agentPortSTPMode obsolete The switch's Port Spanning Tree Protocol Mode
STP mode values are:
dot1d (the default)
fast, indicates you want to use the fast spanning tree mode
off, indicates th… | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.4 |
| agentPortSwitchportMode | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.45 |
| agentPortSTPState obsolete The switch's Port Spanning Tree Protocol State.
This object is only supported when the Dot1d Protocol is enabled. | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.5 |
| agentPortAdminMode The switch's Port Admin Mode | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.6 |
| agentPortPhysicalMode obsolete The switch's Port Speed Mode. This is the configured physical mode.
This object is read-only for gigabit ports | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.7 |
| agentPortPhysicalStatus obsolete The switch's Port Physical Speed Status. This is the current actual speed. | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.8 |
| agentPortLinkTrapMode If enabled, link up and link down traps will be sent for this port. | column | Enumeration | .1.3.6.1.4.1.4526.11.1.2.13.1.9 |