netBotz-prd-bot-amps4-max-range
NETBOTZ-MIB ·
.1.3.6.1.4.1.5528.30.10.61
Object
scalar
mandatory
r/w
Integer32
The maximum RMS milliamps measureable by the fourth Amp Detect.
Context
- MIB
- NETBOTZ-MIB
- OID
.1.3.6.1.4.1.5528.30.10.61- Type
- scalar
- Access
- readwrite
- Status
- mandatory
- Parent
- netBotz-prd-bot
- Siblings
- 137
Syntax
Integer32
- Source
- COPS-PR-SPPIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| netBotz-prd-bot-temp mandatory The reading of the temperature probe, in degrees F or degrees C (depends on netBotz-ismetric). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.1 |
| netBotz-prd-bot-airflow-mins mandatory Minutes without airflow before alarm set. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.10 |
| netBotz-prd-bot-amp1-total-amp-seconds mandatory The accumulated total of amp-seconds on the AmpDetect on port 1. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.102 |
| netBotz-prd-bot-amp1-total-amp-seconds-since-time mandatory The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds on the AmpDetect on port 1.
Writing a value to this attribute resets the accumulated… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.103 |
| netBotz-prd-bot-amp2-total-amp-seconds mandatory The accumulated total of amp-seconds on the AmpDetect on port 2. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.104 |
| netBotz-prd-bot-amp2-total-amp-seconds-since-time mandatory The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds on the AmpDetect on port 2.
Writing a value to this attribute resets the accumulated… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.105 |
| netBotz-prd-bot-amp3-total-amp-seconds mandatory The accumulated total of amp-seconds on the AmpDetect on port 3. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.106 |
| netBotz-prd-bot-amp3-total-amp-seconds-since-time mandatory The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds on the AmpDetect on port 3.
Writing a value to this attribute resets the accumulated… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.107 |
| netBotz-prd-bot-amp4-total-amp-seconds mandatory The accumulated total of amp-seconds on the AmpDetect on port 4. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.108 |
| netBotz-prd-bot-amp4-total-amp-seconds-since-time mandatory The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds on the AmpDetect on port 4.
Writing a value to this attribute resets the accumulated… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.109 |
| netBotz-prd-bot-audio-secs mandatory Seconds of alarm audio before alarm set. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.11 |
| netBotz-prd-bot-amptotal-total-amp-seconds mandatory The accumulated total of amp-seconds on the total of all AmpDetects. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.110 |
| netBotz-prd-bot-amptotal-total-amp-seconds-since-time mandatory The UTC time (seconds since 1/1/1970) of the beginning of the accumulated total of amp-seconds for all AmpDetects.
Writing a value to this attribute resets the accumulated total a… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.111 |
| netBotz-prd-bot-ext-dry1 mandatory The current value of the external dry contact sensor on Ext1: 0=Open, 1=Closed, -1=N/A | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.112 |
| netBotz-prd-bot-ext-dry2 mandatory The current value of the external dry contact sensor on Ext2: 0=Open, 1=Closed, -1=N/A | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.113 |
| netBotz-prd-bot-ext-dry3 mandatory The current value of the external dry contact sensor on Ext3: 0=Open, 1=Closed, -1=N/A | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.114 |
| netBotz-prd-bot-ext-dry4 mandatory The current value of the external dry contact sensor on Ext4: 0=Open, 1=Closed, -1=N/A | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.115 |
| netBotz-prd-bot-ext-dry1-alarm-value mandatory The value to generate alarms on for the external dry contact sensor on Ext1: 0=Open, 1=Closed | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.116 |
| netBotz-prd-bot-ext-dry1-enabled mandatory External dry contact sensor on Ext1 alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.117 |
| netBotz-prd-bot-ext-dry2-alarm-value mandatory The value to generate alarms on for the external dry contact sensor on Ext2: 0=Open, 1=Closed | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.118 |
| netBotz-prd-bot-ext-dry2-enabled mandatory External dry contact sensor on Ext2 alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.119 |
| netBotz-prd-bot-temp-enabled mandatory Temperature probe alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.12 |
| netBotz-prd-bot-ext-dry3-alarm-value mandatory The value to generate alarms on for the external dry contact sensor on Ext3: 0=Open, 1=Closed | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.120 |
| netBotz-prd-bot-ext-dry3-enabled mandatory External dry contact sensor on Ext3 alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.121 |
| netBotz-prd-bot-ext-dry4-alarm-value mandatory The value to generate alarms on for the external dry contact sensor on Ext4: 0=Open, 1=Closed | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.122 |
| netBotz-prd-bot-ext-dry4-enabled mandatory External dry contact sensor on Ext4 alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.123 |
| netBotz-prd-bot-ext-dry1-label mandatory The sensor name/label for the dry contact sensor on Ext1 | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.124 |
| netBotz-prd-bot-ext-dry1-open-label mandatory The sensor name/label for the open(0) state for the dry contact sensor on Ext1 | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.125 |
| netBotz-prd-bot-ext-dry1-closed-label mandatory The sensor name/label for the closed(0) state for the dry contact sensor on Ext1 | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.126 |
| netBotz-prd-bot-ext-dry1-open-to-close-millis mandatory The minimum number of milliseconds that the dry contact sensor on Ext1
must read closed before the state is changed from open to closed. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.127 |
| netBotz-prd-bot-ext-dry1-close-to-open-millis mandatory The minimum number of milliseconds that the dry contact sensor on Ext1
must read openbefore the state is changed from closed to open. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.128 |
| netBotz-prd-bot-ext-dry1-response mandatory The type of alert response for the dry contact sensor on Ext1: ALERT=e-mail with no
pictures, CAMERA=e-mail with pictures from camera. | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.129 |
| netBotz-prd-bot-hum-enabled mandatory Humidity probe alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.13 |
| netBotz-prd-bot-ext-dry2-label mandatory The sensor name/label for the dry contact sensor on Ext2 | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.130 |
| netBotz-prd-bot-ext-dry2-open-label mandatory The sensor name/label for the open(0) state for the dry contact sensor on Ext2 | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.131 |
| netBotz-prd-bot-ext-dry2-closed-label mandatory The sensor name/label for the closed(0) state for the dry contact sensor on Ext2 | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.132 |
| netBotz-prd-bot-ext-dry2-open-to-close-millis mandatory The minimum number of milliseconds that the dry contact sensor on Ext2
must read closed before the state is changed from open to closed. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.133 |
| netBotz-prd-bot-ext-dry2-close-to-open-millis mandatory The minimum number of milliseconds that the dry contact sensor on Ext2
must read openbefore the state is changed from closed to open. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.134 |
| netBotz-prd-bot-ext-dry2-response mandatory The type of alert response for the dry contact sensor on Ext2: ALERT=e-mail with no
pictures, CAMERA=e-mail with pictures from camera. | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.135 |
| netBotz-prd-bot-ext-dry3-label mandatory The sensor name/label for the dry contact sensor on Ext3 | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.136 |
| netBotz-prd-bot-ext-dry3-open-label mandatory The sensor name/label for the open(0) state for the dry contact sensor on Ext3 | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.137 |
| netBotz-prd-bot-ext-dry3-closed-label mandatory The sensor name/label for the closed(0) state for the dry contact sensor on Ext3 | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.138 |
| netBotz-prd-bot-ext-dry3-open-to-close-millis mandatory The minimum number of milliseconds that the dry contact sensor on Ext3
must read closed before the state is changed from open to closed. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.139 |
| netBotz-prd-bot-air-enabled mandatory Airflow probe alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.14 |
| netBotz-prd-bot-ext-dry3-close-to-open-millis mandatory The minimum number of milliseconds that the dry contact sensor on Ext3
must read openbefore the state is changed from closed to open. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.140 |
| netBotz-prd-bot-ext-dry3-response mandatory The type of alert response for the dry contact sensor on Ext3: ALERT=e-mail with no
pictures, CAMERA=e-mail with pictures from camera. | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.141 |
| netBotz-prd-bot-cam-motion mandatory The current motion reading for the camera motion sensor (0=none, 1=motion detected) | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.148 |
| netBotz-prd-bot-cam-motion-enabled mandatory Camera motion sensor alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.149 |
| netBotz-prd-bot-audio-enabled mandatory Audio probe alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.15 |
| netBotz-prd-bot-cam-motion-sensitivity mandatory Camera motion sensor sensitivity: 1=max, 15=min, 0=disabled. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.150 |
| netBotz-prd-bot-cam-motion-delay mandatory Camera motion sensor delay. This is the minimum number of milliseconds of detected
motion required before the alarm is triggered. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.151 |
| netBotz-prd-bot-camera-event-autocycle mandatory Enables (1) or disables (0) the option to have the camera-based responses to
alarm conditions automatically cycle as long as the condition persists. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.152 |
| netBotz-prd-bot-num-pix-before-alarm mandatory Controls the number of pictures to be captured before any triggered alarm. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.153 |
| netBotz-prd-bot-delay-before-event-pix mandatory Controls the number of milliseconds before the first picture is captured
after any triggered alarm. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.154 |
| netBotz-prd-bot-delay-between-event-pix mandatory Controls the number of milliseconds between pictures captured
after any triggered alarm. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.155 |
| netBotz-prd-bot-cam-motion-area-of-motion mandatory Camera motion sensor area of motion: 1=max, 15=min, 0=disabled. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.156 |
| netBotz-prd-bot-cam-pix-for-duration-of-alerts mandatory Camera images gathered for duration of camera related alert: 0=no, 1=yes. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.157 |
| netBotz-prd-bot-camera-enabled mandatory Controls whether the camera is enabled or not: 0=no, 1=yes. Changing this will reboot the appliance. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.158 |
| netBotz-prd-bot-camera-is-flipped mandatory Controls whether the camera image is flipped 180 degress or not: 0=no, 1=yes. Changing this will reboot the appliance. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.159 |
| netBotz-prd-bot-switch-state mandatory Switch state setting. The state controls which
condition of the door switch indicates an alarm.
If set to 0, alarm is set when the switch is closed.
If set to 1, alarm is set when… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.16 |
| netBotz-prd-bot-camera-brightness mandatory Sets the brightness on the camera, from 20 to 180 (20 is low, 180 is high). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.160 |
| netBotz-prd-bot-switch-enabled mandatory Door switch enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.17 |
| netBotz-prd-bot-audio-level mandatory Audio level setting. This is the relative audio level, from 0-11,
above which an alarm will be sent. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.18 |
| netBotz-prd-bot-humidity mandatory The reading of the humidity probe, in percent. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.2 |
| netBotz-prd-bot-trap-index mandatory The crawler ID of the last trap. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.20 |
| netBotz-prd-bot-trap-address mandatory The IP address of the last trap. | scalar | RFC1155-SMIIpAddress | .1.3.6.1.4.1.5528.30.10.21 |
| netBotz-prd-bot-trap-oid mandatory The object id of the last trap. | scalar | ObjectIdentifier | .1.3.6.1.4.1.5528.30.10.22 |
| netBotz-prd-bot-trap-value mandatory The value of the last object trap. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.23 |
| netBotz-prd-bot-trap-date mandatory The date and time of a specific trap. This field
contains the number of seconds elapsed since
midnight (00:00:00), January 1, 1970 | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.24 |
| netBotz-prd-bot-refresh mandatory Rate of web page refresh, in seconds. This must be greater than 5 seconds. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.26 |
| netBotz-prd-bot-airflow-level mandatory Airflow alert level. This is the relative level of airflow below which
an alarm will be sent. The range is 1-11. Each unit is approximately 40 feet/second or 13 meters/second o… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.27 |
| netBotz-prd-bot-doorpic-count mandatory Number of pictures to take when door activated.
These pictures will be sent as attachments to the door alert e-mail.
The range is from 0 to 5 pictures. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.28 |
| netBotz-prd-bot-amps1 mandatory The reading of the first amperage probe, in milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.29 |
| netBotz-prd-bot-airflow mandatory The reading of the airflow probe. Each unit represents approximately 40 feet/minute or
13 meters/minute of airflow velocity. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.3 |
| netBotz-prd-bot-amps1-enabled mandatory Amperage[1] probe alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.30 |
| netBotz-prd-bot-amps1-min mandatory The amperage[1] probe minimum, from 0 to 30000 milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.31 |
| netBotz-prd-bot-amps1-max mandatory The amperage[1] probe maximum, from 0 to 30000 milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.32 |
| netBotz-prd-bot-amps2 mandatory The reading of the second amperage probe, in milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.34 |
| netBotz-prd-bot-amps2-enabled mandatory Amperage[2] probe alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.35 |
| netBotz-prd-bot-amps2-min mandatory The amperage[2] probe minimum, from 0 to 30000 milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.36 |
| netBotz-prd-bot-amps2-max mandatory The amperage[2] probe maximum, from 0 to 30000 milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.37 |
| netBotz-prd-bot-amps3 mandatory The reading of the third amperage probe, in milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.39 |
| netBotz-prd-bot-audio mandatory The reading of the audio alarm probe on/off. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.4 |
| netBotz-prd-bot-amps3-enabled mandatory Amperage[3] probe alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.40 |
| netBotz-prd-bot-amps3-min mandatory The amperage[3] probe minimum, from 0 to 30000 milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.41 |
| netBotz-prd-bot-amps3-max mandatory The amperage[3] probe maximum, from 0 to 30000 milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.42 |
| netBotz-prd-bot-amps-total mandatory The total of the readings of all amperage probes, in milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.44 |
| netBotz-prd-bot-amps-total-enabled mandatory Total amperage alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.45 |
| netBotz-prd-bot-amps-total-min mandatory The total amperage minimum, from 0 to 90000 milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.46 |
| netBotz-prd-bot-amps-total-max mandatory The total amperage maximum, from 0 to 90000 milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.47 |
| netBotz-prd-bot-amps-total-support-enabled mandatory Total Amperage Support enabled(Y) or disabled(N). | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.48 |
| netBotz-prd-bot-amps1-uV-per-10mA mandatory The scaling factor used for the first amperage probe to convert microvolts measured from the
Amp Detect into 10s of milliamps of current. Needs to be set based on the type of Amp… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.49 |
| netBotz-prd-bot-doorajar mandatory The reading of the door switch probe open(1) or closed(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.5 |
| netBotz-prd-bot-amps2-uV-per-10mA mandatory The scaling factor used for the second amperage probe to convert microvolts measured from the
Amp Detect into 10s of milliamps of current. Needs to be set based on the type of Am… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.50 |
| netBotz-prd-bot-amps3-uV-per-mA mandatory The scaling factor used for the third amperage probe to convert microvolts measured from the
Amp Detect into 10s of milliamps of current. Needs to be set based on the type of Amp… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.51 |
| netBotz-prd-bot-amps1-max-range mandatory The maximum RMS milliamps measureable by the first Amp Detect. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.52 |
| netBotz-prd-bot-amps2-max-range mandatory The maximum RMS milliamps measureable by the second Amp Detect. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.53 |
| netBotz-prd-bot-amps3-max-range mandatory The maximum RMS milliamps measureable by the third Amp Detect. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.54 |
| netBotz-prd-bot-amps4 mandatory The reading of the fourth amperage probe, in milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.55 |
| netBotz-prd-bot-amps4-enabled mandatory Amperage[4] probe alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.56 |
| netBotz-prd-bot-amps4-min mandatory The amperage[4] probe minimum, in milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.57 |
| netBotz-prd-bot-amps4-max mandatory The amperage[4] probe maximum, in milliamps. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.58 |
| netBotz-prd-bot-temp-min mandatory The temperature probe minimum, from 35 to 120 degrees F, or 1 to 50 degrees C (depends on netBotz-ismetric). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.6 |
| netBotz-prd-bot-amps4-uV-per-10mA mandatory The scaling factor used for the fourth amperage probe to convert microvolts measured from the
Amp Detect into 10s of milliamps of current. Needs to be set based on the type of Am… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.60 |
| netBotz-prd-bot-ext-temp1 mandatory The reading of the external temperature probe on port 1, in degrees F or degrees C (depends on netBotz-ismetric). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.62 |
| netBotz-prd-bot-ext-temp2 mandatory The reading of the external temperature probe on port 2, in degrees F or degrees C (depends on netBotz-ismetric). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.63 |
| netBotz-prd-bot-ext-temp3 mandatory The reading of the external temperature probe on port 3, in degrees F or degrees C (depends on netBotz-ismetric). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.64 |
| netBotz-prd-bot-ext-temp1-enabled mandatory External temperature probe on port 1 alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.66 |
| netBotz-prd-bot-ext-temp1-min mandatory The external temperature probe on port 1 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.67 |
| netBotz-prd-bot-ext-temp1-max mandatory The external temperature probe on port 1 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.68 |
| netBotz-prd-bot-ext-temp2-enabled mandatory External temperature probe on port 2 alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.69 |
| netBotz-prd-bot-temp-max mandatory The temperature probe maximum, from 35 to 120 degrees F, or 1 to 50 degrees C (depends on netBotz-ismetric). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.7 |
| netBotz-prd-bot-ext-temp2-min mandatory The external temperature probe on port 2 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.70 |
| netBotz-prd-bot-ext-temp2-max mandatory The external temperature probe on port 2 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.71 |
| netBotz-prd-bot-ext-temp3-enabled mandatory External temperature probe on port 3 alarm enabled(1) or disabled(0). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.72 |
| netBotz-prd-bot-ext-temp3-min mandatory The external temperature probe on port 3 probe minimum, in degrees F or degrees C (depends on netBotz-ismetric). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.73 |
| netBotz-prd-bot-ext-temp3-max mandatory The external temperature probe on port 3 probe maximum, in degrees F or degrees C (depends on netBotz-ismetric). | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.74 |
| netBotz-prd-bot-ext-temp1-uV-per-degreeC mandatory The scaling factor used for the external temperature probe on port 1 to convert microvolts measured from the
temperature sensor into degrees C. Needs to be set based on the type … | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.78 |
| netBotz-prd-bot-ext-temp1-uV-at-0-degreeC mandatory The offset used for the external temperature probe on port 1 of microvolts measured from the
temperature sensor at zero degrees C. Needs to be set based on the type of temperatur… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.79 |
| netBotz-prd-bot-humidity-min mandatory The humidity probe minimum, from 10 to 90 percent. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.8 |
| netBotz-prd-bot-ext-temp1-min-range mandatory The minimum temperature measureable by the temperature sensor installed on port 1, in tenths of a degree C.
Needs to be set based on the type of temperature sensor module installe… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.80 |
| netBotz-prd-bot-ext-temp1-max-range mandatory The maximum temperature measureable by the temperature sensor installed on port 1, in tenths of a degree C.
Needs to be set based on the type of temperature sensor module installe… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.81 |
| netBotz-prd-bot-ext-temp2-uV-per-degreeC mandatory The scaling factor used for the external temperature probe on port 2 to convert microvolts measured from the
temperature sensor into degrees C. Needs to be set based on the type … | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.82 |
| netBotz-prd-bot-ext-temp2-uV-at-0-degreeC mandatory The offset used for the external temperature probe on port 2 of microvolts measured from the
temperature sensor at zero degrees C. Needs to be set based on the type of temperatur… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.83 |
| netBotz-prd-bot-ext-temp2-min-range mandatory The minimum temperature measureable by the temperature sensor installed on port 2, in tenths of a degree C.
Needs to be set based on the type of temperature sensor module installe… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.84 |
| netBotz-prd-bot-ext-temp2-max-range mandatory The maximum temperature measureable by the temperature sensor installed on port 2, in tenths of a degree C.
Needs to be set based on the type of temperature sensor module installe… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.85 |
| netBotz-prd-bot-ext-temp3-uV-per-degreeC mandatory The scaling factor used for the external temperature probe on port 3 to convert microvolts measured from the
temperature sensor into degrees C. Needs to be set based on the type … | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.86 |
| netBotz-prd-bot-ext-temp3-uV-at-0-degreeC mandatory The offset used for the external temperature probe on port 3 of microvolts measured from the
temperature sensor at zero degrees C. Needs to be set based on the type of temperatur… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.87 |
| netBotz-prd-bot-ext-temp3-min-range mandatory The minimum temperature measureable by the temperature sensor installed on port 3, in tenths of a degree C.
Needs to be set based on the type of temperature sensor module installe… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.88 |
| netBotz-prd-bot-ext-temp3-max-range mandatory The maximum temperature measureable by the temperature sensor installed on port 3, in tenths of a degree C.
Needs to be set based on the type of temperature sensor module installe… | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.89 |
| netBotz-prd-bot-humidity-max mandatory The humidity probe maximum, from 10 to 90 percent. | scalar | Integer32 | .1.3.6.1.4.1.5528.30.10.9 |
| netBotz-prd-bot-ext-port1-module-id mandatory The module ID of the sensor module installed on port 1. Blank string indicates that no module is installed. | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.94 |
| netBotz-prd-bot-ext-port1-module-type mandatory The type of sensor module installed on port 1. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact sensor. | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.95 |
| netBotz-prd-bot-ext-port2-module-id mandatory The module ID of the sensor module installed on port 2. Blank string indicates that no module is installed. | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.96 |
| netBotz-prd-bot-ext-port2-module-type mandatory The type of sensor module installed on port 2. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact sensor. | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.97 |
| netBotz-prd-bot-ext-port3-module-id mandatory The module ID of the sensor module installed on port 3. Blank string indicates that no module is installed. | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.98 |
| netBotz-prd-bot-ext-port3-module-type mandatory The type of sensor module installed on port 3. NONE=no module, AMP=AmpDetect module, TEMP=temperature sensor, DRY=dry contact sensor. | scalar | RFC1213-MIBDisplayString | .1.3.6.1.4.1.5528.30.10.99 |