nbsSffMsaOpticalConnector
NBS-SFF-MIB ·
.1.3.6.1.4.1.629.204.1.1.1.1.4
Object
column
Integer32
The Optical Connector as reported in the MSA memory map, +1.
Here is the list of values:
1 - unknown
2 - SC
3 - Fiber Channel Style 1 copper connector
4 - Fiber Channel Style 2 copper connector
5 - BNC/TNC
6 - Fiber Channel coaxial headers
7 - Fiberjack
8 - LC
9 - MT-RJ
10 - MU
11 - SG
12 - Optical pigtail
13 - MPO Parllel Optic
14 to 32 - Reserved
33 - HSSDC II
34 - Copper pigtail
35 - RJ45
36 to 128 - Reserved
-- start InfiniBand Annex A6 (CXP)
48 (30h: Passive Copper Cable Assembly)
49 (31h: Active Copper Cable Assembly (ref. Byte 147))
50 (32h: Active Optical Cable Assembly)
51 (33h: Optical Transceiver w/ optical connector)
-- end InfiniBand Annex A6 (CXP)
129 - firewireA (MRV Specific)
130 - cuRJ45 (MRV Specific)
131 - cuRJ45 with LEDs (MRV Specific)
132 - coaxBNC (MRV Specific)
133 - sataDevicePlug (MRV Specific)
134 - sataHostPlug (MRV Specific)
135 - miniCoax (MRV Specific)
136 to 256 - Vendor specific
Context
- MIB
- NBS-SFF-MIB
- OID
.1.3.6.1.4.1.629.204.1.1.1.1.4- Type
- column
- Access
- readonly
- Status
- current
- Parent
- nbsSffMsaEntry
- Table
- nbsSffMsaTable
- Siblings
- 26
Syntax
Integer32
- Source
- COPS-PR-SPPIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| nbsSffMsaPhysicalIfIndex ifIndex from MIB2 | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.629.204.1.1.1.1.1 |
| nbsSffMsaLinkLengthMmf10m This value specifies link length that is supported by the
transceiver while operating in compliance with applicable
standards using 50 micron multimode OM2 [500MHz*km at 850nm,]
f… | column | Integer32 | .1.3.6.1.4.1.629.204.1.1.1.1.10 |
| nbsSffMsaLinkLength625Mmf10m This value specifies link length that is supported by the
transceiver while operating in compliance with applicable
standards using 62.5 micron multimode OM1 [200 MHz*km at
850nm,… | column | Integer32 | .1.3.6.1.4.1.629.204.1.1.1.1.11 |
| nbsSffMsaCopperLinkLength This value specifies the minimum link length that is supported
by the transceiver while operating in compliance with the
applicable standards using copper cable. The value is in u… | column | Integer32 | .1.3.6.1.4.1.629.204.1.1.1.1.12 |
| nbsSffMsaVendorName The vendor name is a 16 character field that contains ASCII
characters, The vendor name shall be the full name of the
corporation, a commonly accepted abbreviation of the name of
… | column | OctetString | .1.3.6.1.4.1.629.204.1.1.1.1.13 |
| nbsSffMsaVendorOUI The vendor organizationally unique identifier field (vendor
OUI) is a 3-byte field that contains the IEEE Company
Identifier for the vendor. A value of all zero in the 3-byte
fiel… | column | OctetString | .1.3.6.1.4.1.629.204.1.1.1.1.14 |
| nbsSffMsaVendorPartNumber The vendor part number (vendor PN) is a 16-byte field that
contains ASCII characters, left-aligned, defining the vendor
part number or product name.
Unlike the MSA … | column | OctetString | .1.3.6.1.4.1.629.204.1.1.1.1.15 |
| nbsSffMsaVendorRevision The vendor revision number (vendor rev) is a 4-byte field that
contains ASCII characters, defining the vendor's product
revision number.
Unlike the MSA standard, ag… | column | OctetString | .1.3.6.1.4.1.629.204.1.1.1.1.16 |
| nbsSffMsaBaseChecksumMatch The check code is a one byte code that can be used to verify
that the first 64 (0-63) bytes of serial information in the
SFP transceiver is valid.Returns yes if checksum matches, … | column | Enumeration | .1.3.6.1.4.1.629.204.1.1.1.1.17 |
| nbsSffMsaLossOfSignalImplemented Byte 65 Bit 1. Signal as defined in the specification | column | Integer32 | .1.3.6.1.4.1.629.204.1.1.1.1.18 |
| nbsSffMsaLossOfSignalInverted Byte 65 Bit 2. Signal as defined in the specification | column | Integer32 | .1.3.6.1.4.1.629.204.1.1.1.1.19 |
| nbsSffMsaIdentifier The MSA Identifier as reported in the MSA memory map, +1.
Some of these MSA Identifiers are also represented in
nbsCmmcPortType from the NBS-CMMC-MIB:
… | column | Enumeration | .1.3.6.1.4.1.629.204.1.1.1.1.2 |
| nbsSffMsaTxFault Byte 65 Bit 3.TX_FAULT signal implemented. Reset definition
in Section III and Laser Fault condition, Generated by laser
safety system. | column | Enumeration | .1.3.6.1.4.1.629.204.1.1.1.1.20 |
| nbsSffMsaTxDisable Byte 65 Bit 4.TX_DISABLE is implemented and disables the
serial output. | column | Integer32 | .1.3.6.1.4.1.629.204.1.1.1.1.21 |
| nbsSffMsaRateSelectImplemented Byte 65 Bit 5.If this bit is set then active control of the
rate select pin is required to change rates. If bit is not
set, no control of pin is required. In all cases, compliance… | column | Enumeration | .1.3.6.1.4.1.629.204.1.1.1.1.22 |
| nbsSffMsaMaxBitRate The upper bit rate limit at which the SFP transceiver will
still meet its specifications (BR, max) is specified in units
of 1% above the nominal bit rate. A value of zero indicate… | column | Integer32 | .1.3.6.1.4.1.629.204.1.1.1.1.23 |
| nbsSffMsaMinBitRate The lower bit rate limit at which the SFP transceiver will
still meet its specifications (BR, min) is specified in units
of 1% below the nominal bit rate. A value of zero indicate… | column | Integer32 | .1.3.6.1.4.1.629.204.1.1.1.1.24 |
| nbsSffMsaVendorSerialNumber The vendor serial number (vendor SN) is a 16 character field
that contains ASCII characters, left-aligned and padded on
the right with ASCII spaces (20h), defining the vendor's
se… | column | OctetString | .1.3.6.1.4.1.629.204.1.1.1.1.25 |
| nbsSffMsaVendorDateCode The date code is an 8-byte field that contains the vendor's
date code in ASCII characters. The date code is mandatory. | column | OctetString | .1.3.6.1.4.1.629.204.1.1.1.1.26 |
| nbsSffMsaExtChecksumMatch The check code is a one byte code that can be used to verify
that the first 32 bytes of extended serial information in the
SFP transceiver is valid. The check code shall be the lo… | column | Enumeration | .1.3.6.1.4.1.629.204.1.1.1.1.27 |
| nbsSffMsaExtIdentifier The field should be set to 04h for all SFP modules indicating
serial ID module definition.
Not supported value: 0 | column | Integer32 | .1.3.6.1.4.1.629.204.1.1.1.1.3 |
| nbsSffMsaTransceiverCodes The following bit significant indicators define the
electronic or optical interfaces that are supported by the
SFP transceiver. At least one bit shall be set in this field.
For Fi… | column | OctetString | .1.3.6.1.4.1.629.204.1.1.1.1.5 |
| nbsSffMsaSerialEncoding The encoding value indicates the serial encoding mechanism
that is the nominal design target of the particular
transceiver. The value shall be contained in the serial data.
For XF… | column | Enumeration | .1.3.6.1.4.1.629.204.1.1.1.1.6 |
| nbsSffMsaNominalBitRate The nominal bit rate (BR, nominal) is specified in units of
100 Megabits per second, rounded off to the nearest 100
Megabits per second. The bit rate includes those bits
necessary… | column | Integer32 | .1.3.6.1.4.1.629.204.1.1.1.1.7 |
| nbsSffMsaLinkLengthSmfKm This value specifies the link length that is supported by the
transceiver while operating in compliance with the applicable
standards using single mode fiber. The value is in unit… | column | Integer32 | .1.3.6.1.4.1.629.204.1.1.1.1.8 |
| nbsSffMsaLinkLengthSmf100m This value specifies the link length that is supported by the
transceiver while operating in compliance with the applicable
standards using single mode fiber. The value is in unit… | column | Integer32 | .1.3.6.1.4.1.629.204.1.1.1.1.9 |