nbsSffDiagsDDMonitoringImplemented
NBS-SFF-MIB ·
.1.3.6.1.4.1.629.204.1.3.1.1.11
Object
column
Enumeration
Byte 92, bit 6. If this bit is set indicating that digital diagnostic monitoring has been implemented, received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage monitoring and temperature monitoring must all be implemented. Additionally, alarm and warning thresholds must be written as specified in this document at locations 00 to 55 on 2 wire serial address 1010001X (A2h)
Context
- MIB
- NBS-SFF-MIB
- OID
.1.3.6.1.4.1.629.204.1.3.1.1.11- Type
- column
- Access
- readonly
- Status
- current
- Parent
- nbsSffDiagsEntry
- Table
- nbsSffDiagsTable
- Siblings
- 62
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | no |
2 | yes |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| nbsSffDiagsRateIdentifier The rate identifier byte refers to several (optional) industry
standard definitions of Rate_Select or Application_Select
control behaviors, intended to manage transceiver optimiza… | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.1 |
| nbsSffDiagsInternallyCalibrated Byte 92, bit 5 Internally Calibrated.
Two calibration options are possible if bit 6 has been set
indicating that digital diagnostic monitoring has been
implemented. If bit 5, Inte… | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.10 |
| nbsSffDiagsOptRateSelectControl Byte 93 bit 1. Optional Rate Select control implemented per
SFF-8431. Sets to 1 if not implemented, 2 if implemented. | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.12 |
| nbsSffDiagsOptAppSelectControl Based on byte 93 bit 2. Optional Application Select control
implemented per SFF-8079. Sets to 1 if not
implemented, 2 if implemented. | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.13 |
| nbsSffDiagsOptSoftRSControlMon Based on byte 93 bit 3. Optional soft RATE_SELECT control and
monitoring implemented. Sets to 1 if not implemented,
2 if implemented. | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.14 |
| nbsSffDiagsOptSoftRxLoSMonitoring Based on byte 93 bit 4. Optional soft RX_LOS monitoring
implemented. Sets to 1 if not implemented, 2 if implemented. | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.15 |
| nbsSffDiagsOptSoftTxFaultMonitoring Based on byte 93 bit 5. Optional soft TX_FAULT monitoring
implemented. Sets to 1 if not implemented, 2 if implemented. | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.16 |
| nbsSffDiagsOptSoftTxDisable Based on byte 93 bit 6. Optional soft TX_DISABLE control and
monitoring implemented.Sets to 1 if not implemented, 2 if
implemented. | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.17 |
| nbsSffDiagsOptAlarmWarningFlags Based on byte 93 bit 7. Optional Alarm/warning flags
implemented for all monitored quantities.Sets to 1 if
not implemented, 2 if implemented. See Table 3.18 | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.18 |
| nbsSffDiags8472Compliance Byte 94 contains an unsigned integer that indicates which
feature set(s) are implemented in the transceiver. | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.19 |
| nbsSffDiagsLinkLengthOm3 This value specifies link length that is supported by the
transceiver while operating in compliance with applicable
standards using 50 micron multimode OM3 [2000 MHz*km] fiber.
Th… | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.2 |
| nbsSffDiagsTemperature Module temperature in centigradese. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.20 |
| nbsSffDiagsTempLowAlarm Predefined temperature for low alarm threshold in
Centigrades. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.21 |
| nbsSffDiagsTempLowWarn Predefined temperature for low warning threshold in
Centigrades | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.22 |
| nbsSffDiagsTempHighWarn Predefined temperature for high warning threshold in
Centigrades | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.23 |
| nbsSffDiagsTempHighAlarm Predefined temperature for high alarm threshold in
Centigrades | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.24 |
| nbsSffDiagsVoltage Internally measured supply voltage in transceiver in the
units of Volts. Bytes 98 & 99 of Address A2h | column | OctetString | .1.3.6.1.4.1.629.204.1.3.1.1.25 |
| nbsSffDiagsVoltLowAlarm Predefined voltage for low alarm threshold in the
units of Volts. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.26 |
| nbsSffDiagsVoltLowWarn Predefined voltage for low warning threshold in the
units of Volts. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.27 |
| nbsSffDiagsVoltHighWarn Predefined voltage for high warning threshold in the
units of Volts. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.28 |
| nbsSffDiagsVoltHighAlarm Predefined voltage for high alarm threshold in the
units of Volts. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.29 |
| nbsSffDiagsLaserWavelength Nominal transmitter output wavelength at room temperature. 16
bit value with byte 60 as high order byte and byte 61 as low
order byte. The laser wavelength is equal to the the 16 … | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.3 |
| nbsSffDiagsBiasCurrent Internally measured TX Bias Current in the units of mA.
Bytes 100 & 101 of Address A2h | column | OctetString | .1.3.6.1.4.1.629.204.1.3.1.1.30 |
| nbsSffDiagsBiasLowAlarm Predefined bias current for low alarm threshold in the
units of mA | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.31 |
| nbsSffDiagsBiasLowWarn Predefined bias current for low warning threshold in
the units of mA | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.32 |
| nbsSffDiagsBiasHighWarn Predefined bias current for high warning threshold in the
units of mA | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.33 |
| nbsSffDiagsBiasHighAlarm Predefined bias current for high alarm threshold in the
units of mA | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.34 |
| nbsSffDiagsTxPower Measured TX output power in the units of dBm. | column | OctetString | .1.3.6.1.4.1.629.204.1.3.1.1.35 |
| nbsSffDiagsTxPowerLowAlarm Predefined Tx output power for low alarm threshold in the
units of dBm. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.36 |
| nbsSffDiagsTxPowerLowWarn Predefined Tx output power for low warning threshold in the
units of dBm. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.37 |
| nbsSffDiagsTxPowerHighWarn Predefined Tx output power for high warning threshold in the
units of dBm. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.38 |
| nbsSffDiagsTxPowerHighAlarm Predefined Tx output power for high alarm threshold in
the units of dBm. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.39 |
| nbsSffDiagsLROutputImplemented Byte 64, bit 0. Value of 1 identifies a conventional
limiting (or unspecified) receiver output. Value of 2
identifies a linear receiver output. | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.4 |
| nbsSffDiagsRxPower Measured received optical power.
Received power, RX_PWR, is given in uW by the
following equation:
Rx_PWR (uW) = Rx_PWR(4) * Rx_PWR AD
4 (16 bit unsigned integer) +
Rx_PWR(3) * Rx… | column | OctetString | .1.3.6.1.4.1.629.204.1.3.1.1.40 |
| nbsSffDiagsRxPowerLowAlarm Predefined Rx input power for low alarm threshold in
the units of dBm. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.41 |
| nbsSffDiagsRxPowerLowWarn Predefined Rx input power for low warning threshold in
the units of dBm. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.42 |
| nbsSffDiagsRxPowerHighWarn Predefined Rx input power for high warning threshold in the
units of dBm. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.43 |
| nbsSffDiagsRxPowerHighAlarm Predefined Rx input power for high alarm threshold in
the units of dBm. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.44 |
| nbsSffDiagsDataReadyBarState Indicates transceiver has achieved power up and data is ready.
Bit remains high until data is ready to be read at which time
the device sets the bit low. Byte 110, bit 0 of A2h | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.45 |
| nbsSffDiagsRxLosState Digital state of the RX_LOS Output Pin. Updated within 100ms
of change on pin. Byte 110, bit 1 of A2h | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.46 |
| nbsSffDiagsTxFaultState Digital state of the TX Fault Output Pin. Updated within
100ms of change on pin. Byte 110, bit 2 of A2h | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.47 |
| nbsSffDiagsSoftRateSelect Read/write bit that allows software rate select control.
Writing 1 selects full bandwidth operation. This bit is
OR'd with the hard Rate_Select, AS(0) or RS(0) pin value.
See Tabl… | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.48 |
| nbsSffDiagsRateSelectState0 Digital state of the SFP Rate_Select Input Pin. Updated within
100ms of change on pin. Note: This pin is also known as AS(0)
in SFF-8079 and RS(0) in SFF-8431. Byte 110, bit 4 of … | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.49 |
| nbsSffDiagsPowerLevelDeclaration Byte 64, bit 1. Value 1 identifies Power Level 1 (or
unspecified) requirements. Value 2 identifies a Power
Level2 requirements. | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.5 |
| nbsSffDiagsRS1State Reserved for digital state of input pin AS(1) per SFF-8079 and
RS(1) per SFF-8431. Updated within 100ms of change on pin. See
A2h Byte 118, Bit 3 for Soft RS(1) Select control inf… | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.50 |
| nbsSffDiagsSoftTxDisableSelect Read/write bit that allows software disable of laser.
Writing 1 disables laser. See Table 3.11 for enable/
disable timing requirements. This bit is OR d with the hard
TX_DISABLE p… | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.51 |
| nbsSffDiagsTxDisableState Digital state of the TX Disable Input Pin. Updated within
100ms of change on pin. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.52 |
| nbsSffDiagsBiasCurrentSlope Fixed decimal (unsigned) calibration data, laser bias
current measured in mA. | column | OctetString | .1.3.6.1.4.1.629.204.1.3.1.1.53 |
| nbsSffDiagsBiasCurrentOffset Fixed decimal (signed two's complement) calibration data,
laser bias current measured in mA. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.54 |
| nbsSffDiagsTxPowerSlope Fixed decimal (unsigned) calibration data, transmitter
coupled output power in the units of dBm. | column | OctetString | .1.3.6.1.4.1.629.204.1.3.1.1.55 |
| nbsSffDiagsTxPowerOffset Fixed decimal (signed two's complement) calibration data,
transmitter coupled output power in the units of dBm. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.56 |
| nbsSffDiagsTemperatureSlope Fixed decimal (unsigned) calibration data, internal module
temperature in C | column | OctetString | .1.3.6.1.4.1.629.204.1.3.1.1.57 |
| nbsSffDiagsTemperatureOffset Fixed decimal (signed two's complement) calibration data,
internal module temperature in C | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.58 |
| nbsSffDiagsVoltageSlope Fixed decimal (unsigned) calibration data, internal module
supply voltage in Volts. | column | OctetString | .1.3.6.1.4.1.629.204.1.3.1.1.59 |
| nbsSffDiagsCooledTranDeclaration Byte 64, bit 2. Value 1 identifies a conventional
uncooled (or unspecified) laser implementation. Value 2
identifies a cooled laser transmitter implementation. | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.6 |
| nbsSffDiagsVoltageOffset Fixed decimal (signed two's complement) calibration data,
internal module supply voltage in Volts. | column | Integer32 | .1.3.6.1.4.1.629.204.1.3.1.1.60 |
| nbsSffDiagsPowerLevelSelect Reserved for SFF-8431 Power Level (maximum power dissipation)
enable.
Value of zero disables Power Level 2 (1.0 Watt max).
Value of one enables Power Level 2 (1.5 Watt max).
Refer… | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.61 |
| nbsSffDiagsPowerLevelOpState Reserved for SFF-8431 Power Level (maximum power dissipation)
status.Value of zero indicates Power Level 1 operation
(1.0 Watt max) Value of one indicates Power Level 2 operation
… | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.62 |
| nbsSffDiagsSoftRSSelect Read/write bit that allows software Tx rate control. Writing
1 selects full speed Tx operation. This bit is OR d with the
hard RS(1) pin value.See Table 3.11 for timing requiremen… | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.63 |
| nbsSffDiagsAddressChangeRequired Byte 92, bit 2 indicates whether or not it is necessary for
the host to perform an address change sequence before
accessing information at 2-wire serial address A2h. If this
bit i… | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.7 |
| nbsSffDiagsPowerMeasurementType Byte 92, bit 3 indicates whether the received power
measurement represents average input optical power or OMA.
If the bit is set, average power is monitored. If it is not,
OMA is … | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.8 |
| nbsSffDiagsExternallyCalibrated Byte 92, bit 4 Externally Calibrated
Two calibration options are possible if bit 6 has been set
indicating that digital diagnostic monitoring has been
implemented. If bit 4 is set… | column | Enumeration | .1.3.6.1.4.1.629.204.1.3.1.1.9 |