genEquipProtectionRevertivePrimaryIDU

MWRM-UNIT-MIB · .1.3.6.1.4.1.2281.10.1.6.13
MIB view Table view

Object

scalar r/w Enumeration 
Decides whether upper or lower IDU will be primary. When placed in a shelf, the upper will be the upper slot in the shelf.
When working in stand-alone mode, the IDU with the highest IP address will be considered as upper.

Context

MIB
MWRM-UNIT-MIB
OID
.1.3.6.1.4.1.2281.10.1.6.13
Type
scalar
Access
readwrite
Status
current
Parent
genEquipProtection
Siblings
16

Syntax

Enumeration

Values & Constraints

Enumerated Values
0lower
1upper

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
genEquipProtectionAdmin
The Admin mode of the protection. In case of protection2Plus2Hsb this parameter should be configured in the main and extension slots.
scalarEnumeration.1.3.6.1.4.1.2281.10.1.6.1
genEquipProtectionCopyToMateStatus
This parameter represents the status of the copy-to-mate command when protection is enabled. - ready(0) - inProgress(1), - success(2), - failure(3)
scalarProgressStatus.1.3.6.1.4.1.2281.10.1.6.10
genEquipProtectionMultiUnitLAGAdmin
This parameter enables the Multi Unit LAG feature. It can be activated only in Single Pipe configuration and only when protection is active (either 1+1 or 2+2).
scalarEnableDisable.1.3.6.1.4.1.2281.10.1.6.11
genEquipProtectionRevertiveAdmin
Enable/Disable revertive protection mode. In revertive protection mode one IDU will be defined as a Primary and the other will be Secondary. Revertive protection will always tend …
scalarEnableDisable.1.3.6.1.4.1.2281.10.1.6.12
genEquipProtectionRevertiveMinTimer
Minimal revertive protection timer period.
scalarInteger32.1.3.6.1.4.1.2281.10.1.6.14
genEquipProtectionRevertiveMaxNumOfTries
Maximal number of revertive protection tries. Used to prevent instability. Revertive protection will give up trying to switch to the primary standby IDU path after the maximal num…
scalarInteger32.1.3.6.1.4.1.2281.10.1.6.15
genEquipProtectionRevertiveTimerMultiplier
A factor that increases the revertive timer period after each try. Setting 1 value will leave the timer period constantly at its minimal value.
scalarInteger32.1.3.6.1.4.1.2281.10.1.6.16
genEquipProtectionAspRevertive
n Smart Pipe HSB mode , this parameter causes the Ethernet line port to be muted upon a complete failure of the radio signal (in both active and standby units)
scalarEnableDisable.1.3.6.1.4.1.2281.10.1.6.17
genEquipProtectionMode
In protection mode, the card can be either active or standby
scalarEnumeration.1.3.6.1.4.1.2281.10.1.6.2
genEquipProtectionMateIPAddr
Same parameter as genEquipNetworkMateIp. In case of 1+1 protection it is the protected card (Mate) IP address. In case of 2+2 protection it is the IP address of the protected unit.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.2281.10.1.6.3
genEquipProtectionMateMACAddr
In case of 1+1 protection it is protected card (Mate) MAC address In case of 2+2 protection it is the IP address of the protected unit.
scalarSNMPv2-TCMacAddress.1.3.6.1.4.1.2281.10.1.6.4
genEquipProtectionRadioExcessiveBERSwitch
The Admin state of an Excessive BER threshold. When enabled, crossing the Excessive BER threshold will cause a protection switch.
scalarEnableDisable.1.3.6.1.4.1.2281.10.1.6.5
genEquipProtectionLockout
This parameter provides the ability to lock the mode of each card in the protection, meaning to force the fact that protection switch will not occur.
scalarOffOn.1.3.6.1.4.1.2281.10.1.6.6
genEquipProtectionForceSwitch
This parameter is a command that forces a protection switch regardless of the state of the standby card.
scalarOffOn.1.3.6.1.4.1.2281.10.1.6.7
genEquipProtectionManualSwitch
This parameter is a command that performs manaual protection switch.
scalarOffOn.1.3.6.1.4.1.2281.10.1.6.8
genEquipProtectionCopyToMateComand
Setting this parameter to On will copy configured parameters from the active to the standby unit.
scalarOffOn.1.3.6.1.4.1.2281.10.1.6.9