genEquipProtectionLockout
MWRM-UNIT-MIB ·
.1.3.6.1.4.1.2281.10.1.6.6
Object
scalar
r/w
OffOn
This parameter provides the ability to lock the mode of each card in the protection, meaning to force the fact that protection switch will not occur.
Context
- MIB
- MWRM-UNIT-MIB
- OID
.1.3.6.1.4.1.2281.10.1.6.6- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- genEquipProtection
- Siblings
- 16
Syntax
OffOn
- Source
- OffOn
- Base type
Enumeration
Values & Constraints
Type Values
0 | off |
1 | on |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| genEquipProtectionAdmin The Admin mode of the protection.
In case of protection2Plus2Hsb this parameter should be configured in
the main and extension slots. | scalar | Enumeration | .1.3.6.1.4.1.2281.10.1.6.1 |
| genEquipProtectionCopyToMateStatus This parameter represents the status of the copy-to-mate command when protection is enabled.
- ready(0)
- inProgress(1),
- success(2),
- failure(3) | scalar | ProgressStatus | .1.3.6.1.4.1.2281.10.1.6.10 |
| genEquipProtectionMultiUnitLAGAdmin This parameter enables the Multi Unit LAG feature.
It can be activated only in Single Pipe configuration and only when protection is active (either 1+1 or 2+2). | scalar | EnableDisable | .1.3.6.1.4.1.2281.10.1.6.11 |
| genEquipProtectionRevertiveAdmin Enable/Disable revertive protection mode. In revertive protection mode one IDU will be defined as a Primary and the other will be Secondary.
Revertive protection will always tend … | scalar | EnableDisable | .1.3.6.1.4.1.2281.10.1.6.12 |
| genEquipProtectionRevertivePrimaryIDU Decides whether upper or lower IDU will be primary. When placed in a shelf, the upper will be the upper slot in the shelf.
When working in stand-alone mode, the IDU with the highe… | scalar | Enumeration | .1.3.6.1.4.1.2281.10.1.6.13 |
| genEquipProtectionRevertiveMinTimer Minimal revertive protection timer period. | scalar | Integer32 | .1.3.6.1.4.1.2281.10.1.6.14 |
| genEquipProtectionRevertiveMaxNumOfTries Maximal number of revertive protection tries. Used to prevent instability. Revertive protection will give up trying to switch
to the primary standby IDU path after the maximal num… | scalar | Integer32 | .1.3.6.1.4.1.2281.10.1.6.15 |
| genEquipProtectionRevertiveTimerMultiplier A factor that increases the revertive timer period after each try. Setting 1 value will leave the timer period constantly at its minimal value. | scalar | Integer32 | .1.3.6.1.4.1.2281.10.1.6.16 |
| genEquipProtectionAspRevertive n Smart Pipe HSB mode , this parameter causes the Ethernet line port to be muted upon a complete failure of
the radio signal (in both active and standby units) | scalar | EnableDisable | .1.3.6.1.4.1.2281.10.1.6.17 |
| genEquipProtectionMode In protection mode, the card can be either active or standby | scalar | Enumeration | .1.3.6.1.4.1.2281.10.1.6.2 |
| genEquipProtectionMateIPAddr Same parameter as genEquipNetworkMateIp.
In case of 1+1 protection it is the protected card (Mate) IP address.
In case of 2+2 protection it is the IP address of the protected unit. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2281.10.1.6.3 |
| genEquipProtectionMateMACAddr In case of 1+1 protection it is protected card (Mate) MAC address
In case of 2+2 protection it is the IP address of the protected unit. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.2281.10.1.6.4 |
| genEquipProtectionRadioExcessiveBERSwitch The Admin state of an Excessive BER threshold. When enabled, crossing the Excessive BER threshold will cause
a protection switch. | scalar | EnableDisable | .1.3.6.1.4.1.2281.10.1.6.5 |
| genEquipProtectionForceSwitch This parameter is a command that forces a protection switch regardless of the state of the standby card. | scalar | OffOn | .1.3.6.1.4.1.2281.10.1.6.7 |
| genEquipProtectionManualSwitch This parameter is a command that performs manaual protection switch. | scalar | OffOn | .1.3.6.1.4.1.2281.10.1.6.8 |
| genEquipProtectionCopyToMateComand Setting this parameter to On will copy configured parameters from the active to the standby unit. | scalar | OffOn | .1.3.6.1.4.1.2281.10.1.6.9 |