mplsTunnelAssociateLinearProt
LUM-MPLS-MIB ·
.1.3.6.1.4.1.8708.2.40.2.4.1.1.17
Object
column
LUM-TCCommandString
Internal command for create and associate a PSC
(Protection State Coordination) protocol for linear protection of the tunnel.
Only supported 1:1 protection architecture: a protection transport path is
dedicated to the working transport path of a single service and the traffic
is only transmitted either on the working or the protection path, by
using a selector at the source of the protection domain.
The active LSP associated with the tunnel will be the working path.
Protection path -- the Identifier of the protection LSP path
Mode -- revertive/non-revertive mode of the protection domain
WTR timer -- wait-to-restore timer, used to delay reversion to
normal state when recovering from a failure condition
on the working path and the protection domain is
configured for revertive behavior
Continuous message interval
-- interval of continuous control message
Rapid message interval
-- interval of three rapid control messages
After associate the linear protection, the cross reference of the protection
LSP and the tunnel will be displayed in mplsTnlXLspTable.
Context
- MIB
- LUM-MPLS-MIB
- OID
.1.3.6.1.4.1.8708.2.40.2.4.1.1.17- Type
- column
- Access
- readonly
- Status
- current
- Parent
- mplsTunnelEntry
- Table
- mplsTunnelTable
- Siblings
- 23
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| mplsTunnelIndex An arbitrary index assigned to each entry. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.4.1.1.1 |
| mplsTunnelDestNodeId The ID of the destination node, i.e. the node
where this tunnel terminates. Used for externally uniquely
identifying the tunnel in the standardized format,
'[Src Global ID]:[Src N… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.4.1.1.10 |
| mplsTunnelDestTunnelId The destination node MPLS-TP tunnel ID of the tunnel.
Used for externally uniquely identifying the tunnel
in the standardized format,
'[Src global ID]:[Src node ID]:[Src tunnel ID… | column | MplsIdentifier | .1.3.6.1.4.1.8708.2.40.2.4.1.1.11 |
| mplsTunnelExtId The global ID of the tunnel, used for externally
uniquely identifying the tunnel in the standardized format,
'[Src global ID]:[Src node ID]:[Src tunnel ID]-
[Dest. global ID]:[Des… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.40.2.4.1.1.12 |
| mplsTunnelAssociateLSP Internal command for mapping a new LSP to the tunnel.
The first LSP associated to the tunnel will be the
primary path and the additional LSPs will be the
protection path.
… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.4.1.1.13 |
| mplsTunnelRowStatus Manages creation and deletion of conceptual rows.
See also SNMPv2-TC.
Note: The newly created object will not necessarily
receive the same index as used in the crea… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.8708.2.40.2.4.1.1.14 |
| mplsTunnelLinearProtection The linear protection profile applied to the tunnel.
Protection state coordination (PSC) protocol is used
for linear protection. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.40.2.4.1.1.15 |
| mplsTunnelProtectionState Status of the linear protection that applied to the tunnel
fullyworking (1) -- both protection and working path are fully active
degraded (2) -- service degraded on the protec… | column | Enumeration | .1.3.6.1.4.1.8708.2.40.2.4.1.1.16 |
| mplsTunnelGlobalId This object allows the administrator to assign a unique
operator identifier also called MPLS-TP Global
Identifier.
The Global Identifier can contain the 2-octet or
4-octet value o… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.4.1.1.18 |
| mplsTunnelDestGlobalId This object allows the administrator to assign a unique
operator identifier also called MPLS-TP Global
Identifier.
The Global Identifier can contain the 2-octet or
4-octet value o… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.4.1.1.19 |
| mplsTunnelInternalReference For internal use only. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.4.1.1.2 |
| mplsTunnelWorkingLSP Identifier of the working path of the linear protection. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.40.2.4.1.1.20 |
| mplsTunnelProtectionLSP Identifier of the protection path of the linear protection. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.40.2.4.1.1.21 |
| mplsTunnelReservedBW Bandwidth reserved by the tunnel.
Default value is 0 and indicates that no bandwidth
has been allocated by the tunnel. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.4.1.1.22 |
| mplsTunnelBookedBW The total amount of bandwidth booked by pseudowires in the tunnel. | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.8708.2.40.2.4.1.1.23 |
| mplsTunnelDescr User configurable label. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.40.2.4.1.1.24 |
| mplsTunnelIdentifier Unique identifier used for referencing this object. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.40.2.4.1.1.3 |
| mplsTunnelName The management name of the entry, for example
'tunnel:1:2:id', where the first number indicates
subrack, the second slot number and the id
is the unique tunnel identifier. | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.40.2.4.1.1.4 |
| mplsTunnelActiveLSP ID of the associated LSP that is active, if exists. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.40.2.4.1.1.5 |
| mplsTunnelActiveLspIndex The index of the associated LSP that is active,
if exists. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.4.1.1.6 |
| mplsTunnelState Indicates the state of the tunnel.
down (1)
-- The tunnel is de-actived or unavailable to carry any traffic.
up (2)
-- The tunnel is active and ready to carry traffic.… | column | Enumeration | .1.3.6.1.4.1.8708.2.40.2.4.1.1.7 |
| mplsTunnelSrcNodeId The ID of the source node, i.e. the node where this
tunnel originates. Used for externally uniquely
identifying the tunnel in the standardized format,
'[Src Global ID]:[Src Node I… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.4.1.1.8 |
| mplsTunnelSrcTunnelId The source node MPLS-TP tunnel ID of this tunnel.
Used for externally uniquely identifying the tunnel
in the standardized format,
'[Src Global ID]:[Src Node ID]:[Src Tunnel ID]-
[… | column | MplsIdentifier | .1.3.6.1.4.1.8708.2.40.2.4.1.1.9 |