mplsNodeLPContMsgInterval

LUM-MPLS-MIB · .1.3.6.1.4.1.8708.2.40.2.5.1.1.14
MIB view Table view

Object

column r/w Unsigned32 
In linear protection domain, the control message is transmitted over
the protection path only.
Subsequent messages are continuously transmitted to verify that the
session is alive. If no valid control message is received, that last
valid received message is applicable.
The continuous message interval is configured for all linear
protection service on the board.
Unit: second.

Context

MIB
LUM-MPLS-MIB
OID
.1.3.6.1.4.1.8708.2.40.2.5.1.1.14
Type
column
Access
readwrite
Status
current
Parent
mplsNodeEntry
Table
mplsNodeTable
Siblings
24

Syntax

Unsigned32

Values & Constraints

Object Constraints
range: 1-30

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
mplsNodeIndex
An arbitrary index assigned to each entry.
columnUnsigned32.1.3.6.1.4.1.8708.2.40.2.5.1.1.1
mplsNodeCreatePw
Pseudowire ID - Unique pseudowire ID used when referencing the pseudowire within the node. Pseudowire type - Edge pseudowire connects to a singel tunnel …
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.10
mplsNodeCreateIf
Internal command for creating an interface. Identifier - Unique MPLS interface ID used when referencing the interface within the node. Admin Status - Defines whet…
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.11
mplsNodeLinearProtMode
The mode of the protection domain, configured for all MPLS linear protection service on the board. nonRevertive (1) -- non-revertive mode revertive (2) -- revertive mode
columnEnumeration.1.3.6.1.4.1.8708.2.40.2.5.1.1.12
mplsNodeLinearProtWtrTimer
The wait-to-restore (WTR) timer configured for all MPLS linear protection service on the board. A WTR timer is used to delay reversion to Normal state when recovering from a failu…
columnUnsigned32.1.3.6.1.4.1.8708.2.40.2.5.1.1.13
mplsNodeLPRapidMsgInterval
In linear protection domain, when the state of the protection domain is changed, three control messages shall be transmitted as quickly as possible to allow for rapid protection s…
columnUnsigned32.1.3.6.1.4.1.8708.2.40.2.5.1.1.15
mplsNodeGlobalId
This object allows the administrator to assign a unique operator identifier also called MPLS-TP Global Identifier. The Global Identifier can contain the 2-octet or 4-octet value o…
columnUnsigned32.1.3.6.1.4.1.8708.2.40.2.5.1.1.16
mplsNodeCreateMsPw
Internal command for creating a multi-segment pseudowire. Identifier - Unique pseudowire ID used when referencing the pseudowire within the node. East outlabe…
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.17
mplsNodeCreateLsp2
Internal command for creating a bidirectional LSP entry. Identifier - Unique LSP ID used when referencing the LSP within the node. Role …
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.18
mplsNodeCreateTunnelAdvanced
Identifier - Unique tunnel ID used when referencing the tunnel within the node. MPLS-TP ID - Set the standard MPLS-TP ID for the tunnel o…
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.19
mplsNodeName
The management name of the interface, for example 'node:1:2', where the first number indicates subrack, the second slot number.
columnLUM-TCMgmtNameString.1.3.6.1.4.1.8708.2.40.2.5.1.1.2
mplsNodeCreateLspAdvanced
Internal command for creating a bidirectional LSP entry. Identifier - Unique LSP ID used when referencing the LSP within the node. Role …
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.20
mplsNodeCreatePwGeneric
Internal command for creating a bidirectional LSP entry. Identifier - Unique LSP ID used when referencing the LSP within the node.
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.21
mplsNodeCreatePwMpls
Internal command for creating a bidirectional LSP entry. Identifier - Unique LSP ID used when referencing the LSP within the node.
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.22
mplsNodeCreatePwEnet
Internal command for creating a bidirectional LSP entry. Identifier - Unique LSP ID used when referencing the LSP within the node.
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.23
mplsNodeCreateBfdTemplate
Internal command for creating a new BFD template. Identifier - The unique identifier for the template. Tx Interval - Minimum interval for sending BFD…
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.24
mplsNodeCreateXCAdvanced
Internal command for creating a XC entry. In-segment name - Name of the incoming segment. In-segment label - The MPLS label for the incoming traffic. Out-se…
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.25
mplsNodeSubrack
The subrack that this MPLS node belongs to.
columnUnsigned32.1.3.6.1.4.1.8708.2.40.2.5.1.1.3
mplsNodeSlot
The slot that this MPLS node belongs to.
columnUnsigned32.1.3.6.1.4.1.8708.2.40.2.5.1.1.4
mplsNodeIccIdStr
Unique code assigned to the network operator or service provider maintained by ITU-T. The ITU carrier code used to form a globally unique node ID for non IP environments.
columnOctetString.1.3.6.1.4.1.8708.2.40.2.5.1.1.5
mplsNodeIdNum
Unique node ID / router ID assigned with in the scope of the network of the operator / service provider, defined by the ICC ID. This value is unique and only valid for this board.…
columnUnsigned32.1.3.6.1.4.1.8708.2.40.2.5.1.1.6
mplsNodeCreateXC
Internal command for creating a XC entry. In-segment name - Name of the incoming segment. In-segment label - The MPLS label for the incoming traffic. Out-se…
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.7
mplsNodeCreateTunnel
Identifier - Unique tunnel ID used when referencing the tunnel within the node. MPLS-TP ID - Set the standard MPLS-TP ID for the tunnel o…
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.8
mplsNodeCreateLsp
Internal command for creating a bidirectional LSP entry. Identifier - Unique LSP ID used when referencing the LSP within the node. Role …
columnLUM-TCCommandString.1.3.6.1.4.1.8708.2.40.2.5.1.1.9