mplsNodeIdNum
LUM-MPLS-MIB ·
.1.3.6.1.4.1.8708.2.40.2.5.1.1.6
Object
column
r/w
Unsigned32
Unique node ID / router ID assigned with in the scope
of the network of the operator / service provider,
defined by the ICC ID. This value is unique and only
valid for this board.
Accepted values are 0.0.0.0 - 255.255.255.255.
If this value is changed all MPLS-TP MP IDs on this
board will be updated. All BFD sessions on the board will
need to be in administrative down.
Context
- MIB
- LUM-MPLS-MIB
- OID
.1.3.6.1.4.1.8708.2.40.2.5.1.1.6- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- mplsNodeEntry
- Table
- mplsNodeTable
- Siblings
- 24
Syntax
Unsigned32
Values & Constraints
Object Constraints
range: 0-4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| mplsNodeIndex An arbitrary index assigned to each entry. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.5.1.1.1 |
| mplsNodeCreatePw Pseudowire ID - Unique pseudowire ID used when referencing
the pseudowire within the node.
Pseudowire type - Edge pseudowire connects to a singel tunnel … | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.10 |
| mplsNodeCreateIf Internal command for creating an interface.
Identifier - Unique MPLS interface ID used when referencing
the interface within the node.
Admin Status - Defines whet… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.11 |
| mplsNodeLinearProtMode The mode of the protection domain, configured for all MPLS linear
protection service on the board.
nonRevertive (1) -- non-revertive mode
revertive (2) -- revertive mode | column | Enumeration | .1.3.6.1.4.1.8708.2.40.2.5.1.1.12 |
| mplsNodeLinearProtWtrTimer The wait-to-restore (WTR) timer configured for all MPLS linear
protection service on the board.
A WTR timer is used to delay reversion to Normal state
when recovering from a failu… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.5.1.1.13 |
| mplsNodeLPContMsgInterval In linear protection domain, the control message is transmitted over
the protection path only.
Subsequent messages are continuously transmitted to verify that the
session is alive… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.5.1.1.14 |
| mplsNodeLPRapidMsgInterval In linear protection domain, when the state of the protection domain
is changed, three control messages shall be transmitted as quickly as
possible to allow for rapid protection s… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.5.1.1.15 |
| mplsNodeGlobalId This object allows the administrator to assign a unique
operator identifier also called MPLS-TP Global
Identifier.
The Global Identifier can contain the 2-octet or
4-octet value o… | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.5.1.1.16 |
| mplsNodeCreateMsPw Internal command for creating a multi-segment pseudowire.
Identifier - Unique pseudowire ID used when referencing
the pseudowire within the node.
East outlabe… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.17 |
| mplsNodeCreateLsp2 Internal command for creating a bidirectional LSP entry.
Identifier - Unique LSP ID used when referencing
the LSP within the node.
Role … | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.18 |
| mplsNodeCreateTunnelAdvanced Identifier - Unique tunnel ID used when referencing
the tunnel within the node.
MPLS-TP ID - Set the standard MPLS-TP ID for the
tunnel o… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.19 |
| mplsNodeName The management name of the interface, for example
'node:1:2', where the first number indicates
subrack, the second slot number. | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.2 |
| mplsNodeCreateLspAdvanced Internal command for creating a bidirectional LSP entry.
Identifier - Unique LSP ID used when referencing
the LSP within the node.
Role … | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.20 |
| mplsNodeCreatePwGeneric Internal command for creating a bidirectional LSP entry.
Identifier - Unique LSP ID used when referencing
the LSP within the node. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.21 |
| mplsNodeCreatePwMpls Internal command for creating a bidirectional LSP entry.
Identifier - Unique LSP ID used when referencing
the LSP within the node. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.22 |
| mplsNodeCreatePwEnet Internal command for creating a bidirectional LSP entry.
Identifier - Unique LSP ID used when referencing
the LSP within the node. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.23 |
| mplsNodeCreateBfdTemplate Internal command for creating a new BFD template.
Identifier - The unique identifier for the template.
Tx Interval - Minimum interval for sending BFD… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.24 |
| mplsNodeCreateXCAdvanced Internal command for creating a XC entry.
In-segment name - Name of the incoming segment.
In-segment label - The MPLS label for the incoming
traffic.
Out-se… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.25 |
| mplsNodeSubrack The subrack that this MPLS node belongs to. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.5.1.1.3 |
| mplsNodeSlot The slot that this MPLS node belongs to. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.40.2.5.1.1.4 |
| mplsNodeIccIdStr Unique code assigned to the network operator or
service provider maintained by ITU-T.
The ITU carrier code used to form a globally unique
node ID for non IP environments. | column | OctetString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.5 |
| mplsNodeCreateXC Internal command for creating a XC entry.
In-segment name - Name of the incoming segment.
In-segment label - The MPLS label for the incoming
traffic.
Out-se… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.7 |
| mplsNodeCreateTunnel Identifier - Unique tunnel ID used when referencing
the tunnel within the node.
MPLS-TP ID - Set the standard MPLS-TP ID for the
tunnel o… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.8 |
| mplsNodeCreateLsp Internal command for creating a bidirectional LSP entry.
Identifier - Unique LSP ID used when referencing
the LSP within the node.
Role … | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.40.2.5.1.1.9 |