ethIfAdminStatus
LUM-ETH-MIB ·
.1.3.6.1.4.1.8708.2.18.2.2.1.1.11
Object
The administrative state for the interface.
down - The interface should be inactive.
service - The interface is activated but alarms
are suppressed. Intended for use during service
or re-configuration. When service is concluded
adminStatus should be set to 'up' again.
up - The interface should be activated when
it becomes available. Alarms are not suppressed.
Context
- MIB
- LUM-ETH-MIB
- OID
.1.3.6.1.4.1.8708.2.18.2.2.1.1.11- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- ethIfEntry
- Table
- ethIfTable
- Siblings
- 39
Values & Constraints
Type Values
1 | down |
2 | service |
3 | up |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ethIfIndex An arbitrary index assigned to each entry. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.18.2.2.1.1.1 |
| ethIfHighSpeed The expected signal bit rate in units of
1,000,000 bits (Mb) per second. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.18.2.2.1.1.10 |
| ethIfOperStatus The operational state for the interface.
notPresent - The physical resources are not
available.
down - The interface is de-activated or the are
fault… | column | LUM-TCBoardOrInterfaceOperStatus | .1.3.6.1.4.1.8708.2.18.2.2.1.1.12 |
| ethIfLaserStatus The operational state of the laser.
off - The laser is turned off.
on - The laser is turned on. | column | Enumeration | .1.3.6.1.4.1.8708.2.18.2.2.1.1.13 |
| ethIfTxSignalStatus The operational state for outgoing (TX) signal
of the interface.
down - A fault that would lead to a protection
switch has occurred.
degraded - The s… | column | Enumeration | .1.3.6.1.4.1.8708.2.18.2.2.1.1.14 |
| ethIfAutoNegotiationMode The wanted auto negotiation mode.
off - auto negotiation process is disabled
on - auto negotiation process is enabled | column | Enumeration | .1.3.6.1.4.1.8708.2.18.2.2.1.1.15 |
| ethIfAutoNegotiationStatus The result of the auto negotiation procedure
incomplete - the result is still pending
half - half duplex
full - full duplex | column | Enumeration | .1.3.6.1.4.1.8708.2.18.2.2.1.1.16 |
| ethIfDuplexCapability The duplex capability of the HW.
half - supports half duplex
full - supports full duplex | column | Enumeration | .1.3.6.1.4.1.8708.2.18.2.2.1.1.17 |
| ethIfFlowControlMode The mode for handling of pause messages between
the peers.
noPause - PAUSE frame reception and
transmission is disabled
rxPause - PAUSE frame rece… | column | Enumeration | .1.3.6.1.4.1.8708.2.18.2.2.1.1.18 |
| ethIfInterPacketGap Time between the frames in nano seconds.
Legal values are 72, 80, ... 200, 320, 328,
336, ... 456 | column | Unsigned32 | .1.3.6.1.4.1.8708.2.18.2.2.1.1.19 |
| ethIfName The management name of the interface, for
example 'eth1:2:1', where the first number
indicates sub-rack, the second slot number and
the third is the port number.
Examples:
… | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.18.2.2.1.1.2 |
| ethIfFrameSize The maximum size of the transmitted and
received frames (in bytes). | column | Unsigned32 | .1.3.6.1.4.1.8708.2.18.2.2.1.1.20 |
| ethIfPowerLevel The received power level in units of 0.1 dBm. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.18.2.2.1.1.21 |
| ethIfPowerLevelHighThreshold deprecated The upper threshold for received power level
in units of 0.1 dBm. | column | Integer32 | .1.3.6.1.4.1.8708.2.18.2.2.1.1.22 |
| ethIfPowerLevelLowThreshold deprecated The lower threshold for received power level
in units of 0.1 dBm. | column | Integer32 | .1.3.6.1.4.1.8708.2.18.2.2.1.1.23 |
| ethIfLaserBias Measures laser bias current value in tenths
of mA (0.1 mA). | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.18.2.2.1.1.24 |
| ethIfLaserBiasThreshold Sets the threshold for the laser bias alarm.
in percentage relative to the value set during
production. The preset value is 100%. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.18.2.2.1.1.25 |
| ethIfLossOfSignal Loss of signal.
Applicable for all signal formats.
A(ctivation): Active loss of signal HW
indication.
D(e-activation): Inactive loss of signal HW
ind… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.18.2.2.1.1.26 |
| ethIfReceivedPowerHigh Received power level high threshold exceeded.
A: The received power level exceeds the
associated threshold.
D: The received power level is 0.5 dB bel… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.18.2.2.1.1.27 |
| ethIfReceivedPowerLow Received power level low threshold exceeded.
A: The received power level is below the
associated threshold.
D: The received power level is 0.5 dB abo… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.18.2.2.1.1.28 |
| ethIfLaserBiasHigh Laser bias high threshold exceeded.
A: The laser bias current exceeds the associated
threshold.
D: The laser bias current is 0.5 mA below the
associa… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.18.2.2.1.1.29 |
| ethIfDescr User configurable label. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.18.2.2.1.1.3 |
| ethIfLossOfSync Loss of sync.
A: GbE 'frame' can not be located.
D: GbE 'frame' is located. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.18.2.2.1.1.30 |
| ethIfBitrateMismatch Bitrate mismatch.
A: The interface is unable to lock to the
inserted signal.
D: The interface is able to lock to the
inserted signal. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.18.2.2.1.1.31 |
| ethIfLinkDown A: Failure to negotiate a connection with the
other party.
D: A connection is negotiated. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.18.2.2.1.1.32 |
| ethIfAuAlarmIndicationSignalW2C Payload Alarm indication signal (AIS) on the
trunk-side.
A: An 'all ones' SDH signal is detected.
D: SDH signal recovered. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.18.2.2.1.1.33 |
| ethIfForwardAls Forward Automatic Laser Shut-down. Decides
the behaviour of the client laser (W2C) when
the trunc signal is defected.
disabled - The laser is NOT turned off at
fail… | column | Enumeration | .1.3.6.1.4.1.8708.2.18.2.2.1.1.34 |
| ethIfSuppressRemoteAlarms Suppress AIS in the alarm list. The fault
status on the port object can, however, be seen.
disabled - alarms are not suppressed.
enabled - alarms are… | column | Enumeration | .1.3.6.1.4.1.8708.2.18.2.2.1.1.35 |
| ethIfFarEndLoopback Loop the client TX signal back to the client RX.
disabled - the signal is not looped
enabled - the signal is looped. | column | Enumeration | .1.3.6.1.4.1.8708.2.18.2.2.1.1.36 |
| ethIfEntityId Index in entity table.
-- Only used for notifications | column | Unsigned32 | .1.3.6.1.4.1.8708.2.18.2.2.1.1.37 |
| ethIfGbeUtilization Shows a snapshot of the current bandwidth
utilization of the GbE signal during the
last second.
It is expressed in per cent of 1 Gbps | column | Unsigned32 | .1.3.6.1.4.1.8708.2.18.2.2.1.1.38 |
| ethIfObjectProperty Property mask. | column | LUM-TCObjectProperty | .1.3.6.1.4.1.8708.2.18.2.2.1.1.39 |
| ethIfSubrack The number of the subrack where the interface
is located. | column | LUM-TCSubrackNumber | .1.3.6.1.4.1.8708.2.18.2.2.1.1.4 |
| ethIfPowerLevelLowRelativeThreshold The lower threshold for received power level in
units of 0.1 dB, relative to the receiver
sensitivity. | column | Integer32 | .1.3.6.1.4.1.8708.2.18.2.2.1.1.40 |
| ethIfSlot The number of the slot where the interface is
located. | column | LUM-TCSlotNumber | .1.3.6.1.4.1.8708.2.18.2.2.1.1.5 |
| ethIfTxPort The number of the port where the TX-side of
the interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.18.2.2.1.1.6 |
| ethIfRxPort The number of the port where the RX-side of
the interface is located. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.18.2.2.1.1.7 |
| ethIfInvPhysIndexOrZero The row in the invPhysTable for this interface.
Set to 0 if not known. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.18.2.2.1.1.8 |
| ethIfFormat The expected signal format.
The default value is board dependent. For information
about the default value for this particular board,
please refer to the user manual. | column | EthSignalFormat | .1.3.6.1.4.1.8708.2.18.2.2.1.1.9 |