juniHdlcIfRowStatus – Juniper-HDLC-MIB

Object

column r/w SNMPv2-TCRowStatus

Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
    createAndGo
    destroy
              
To create an entry in this table, the following entry objects MUST be
explicitly configured:
    juniHdlcIfRowStatus
    juniHdlcIfLowerIfIndex
              
In addition, when creating an entry the following conditions must hold:
              
    A value for juniHdlcIfIndex must have been determined previously, by
    reading juniHdlcNextIfIndex.
              
    The interface identified by juniHdlcIfLowerIfIndex must exist.
              
A corresponding entry in ifTable/ifXTable/juniIfTable is created/
destroyed as a result of creating/destroying an entry in this table.

Context

MIB: Juniper-HDLC-MIB
OID: .1.3.6.1.4.1.4874.2.2.9.1.2.1.2
Type: column
Access: readwrite
Status: current
Parent: juniHdlcIfEntry
Table: juniHdlcIfTable
Siblings: 10

Syntax

SNMPv2-TCRowStatus

Source: SNMPv2-TCRowStatus
Base type: Enumeration

Values & Constraints

Type Values

`1`	active
`2`	notInService
`3`	notReady
`4`	createAndGo
`5`	createAndWait
`6`	destroy

Related Objects

Sibling Objects

Object	Type	Syntax	OID
juniHdlcIfIndex The ifIndex of the HDLC interface. When creating entries in this table, suitable values for this object are determined by reading juniHdlcNextIfIndex.	column	IF-MIBInterfaceIndex	`.1.3.6.1.4.1.4874.2.2.9.1.2.1.1`
juniHdlcIfForceDteAck The force DTE acknowledge setting. This object is only applicable to HDLC interfaces directly over a high speed serial interface (HSSI). This is set to force Cisco compatibility …	column	Enumeration	`.1.3.6.1.4.1.4874.2.2.9.1.2.1.10`
juniHdlcIfIdleCharacter The HDLC idle character has two possible settings. The value can be set to idleCharacterFlags which translates to 0x7E or it can be set to idleCharacterMarks which translates to …	column	Enumeration	`.1.3.6.1.4.1.4874.2.2.9.1.2.1.11`
juniHdlcIfLowerIfIndex The ifIndex of an interface over which this HDLC interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value …	column	IF-MIBInterfaceIndexOrZero	`.1.3.6.1.4.1.4874.2.2.9.1.2.1.3`
juniHdlcIfMtu The Maximum Transmission Unit (MTU) this interface is permitted to transmit. At creation, if a value for this object is not specified, a default will be chosen that…	column	octets Integer32	`.1.3.6.1.4.1.4874.2.2.9.1.2.1.4`
juniHdlcIfMru The Maximum Receive Unit (MRU) this interface is permitted to receive. At creation, if a value for this object is not specified, a default will be chosen that is su…	column	octets Integer32	`.1.3.6.1.4.1.4874.2.2.9.1.2.1.5`
juniHdlcIfCrcSize Selects the CRC size: none, 16 bits, or 32 bits.	column	Enumeration	`.1.3.6.1.4.1.4874.2.2.9.1.2.1.6`
juniHdlcIfDataPolarity Polarity of data transmitted on this HDLC interface. Inverted data is used for certain line coding configurations to ensure sufficient one's density for timing recovery by the re…	column	Enumeration	`.1.3.6.1.4.1.4874.2.2.9.1.2.1.7`
juniHdlcIfClockMode The clock mode setting for this HDLC interface. This object is only applicable to HDLC interfaces directly over a high speed serial interface (HSSI). At creation, …	column	Enumeration	`.1.3.6.1.4.1.4874.2.2.9.1.2.1.8`
juniHdlcIfClockRate The clock rate setting for this HDLC interface. This object is only applicable to HDLC interfaces directly over a high speed serial interface (HSSI). At creation, …	column	Enumeration	`.1.3.6.1.4.1.4874.2.2.9.1.2.1.9`