juniHdlcIfClockRate
Juniper-HDLC-MIB ·
.1.3.6.1.4.1.4874.2.2.9.1.2.1.9
Object
column
r/w
Enumeration
The clock rate setting for this HDLC interface. This object is only
applicable to HDLC interfaces directly over a high speed serial
interface (HSSI).
At creation, if a value for this object is not specified, a default will
be chosen that is suitable for the type of lower interface on which this
interface is stacked. If the lower interface is not HSSI, then the
default value will be hdlcClockRateUnsupported(0); if the lower
interface is HSSI then the default value will be
hdlcClockRate44At736Mhz(2).
Context
- MIB
- Juniper-HDLC-MIB
- OID
.1.3.6.1.4.1.4874.2.2.9.1.2.1.9- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- juniHdlcIfEntry
- Table
- juniHdlcIfTable
- Siblings
- 10
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | hdlcClockRateUnsupported |
1 | hdlcClockRate34At368Mhz |
2 | hdlcClockRate44At736Mhz |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| juniHdlcIfIndex The ifIndex of the HDLC interface. When creating entries in this
table, suitable values for this object are determined by reading
juniHdlcNextIfIndex. | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.4874.2.2.9.1.2.1.1 |
| juniHdlcIfForceDteAck The force DTE acknowledge setting. This object is only applicable to
HDLC interfaces directly over a high speed serial interface (HSSI).
This is set to force Cisco compatibility … | column | Enumeration | .1.3.6.1.4.1.4874.2.2.9.1.2.1.10 |
| juniHdlcIfIdleCharacter The HDLC idle character has two possible settings. The value can be
set to idleCharacterFlags which translates to 0x7E or it can be set to
idleCharacterMarks which translates to … | column | Enumeration | .1.3.6.1.4.1.4874.2.2.9.1.2.1.11 |
| juniHdlcIfRowStatus Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy
… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.4874.2.2.9.1.2.1.2 |
| juniHdlcIfLowerIfIndex The ifIndex of an interface over which this HDLC interface is to be
layered. A value of zero indicates no layering. An implementation may
choose to require that a nonzero value … | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.4874.2.2.9.1.2.1.3 |
| juniHdlcIfMtu The Maximum Transmission Unit (MTU) this interface is permitted to
transmit.
At creation, if a value for this object is not specified, a default will
be chosen that… | column | octets Integer32 | .1.3.6.1.4.1.4874.2.2.9.1.2.1.4 |
| juniHdlcIfMru The Maximum Receive Unit (MRU) this interface is permitted to receive.
At creation, if a value for this object is not specified, a default will
be chosen that is su… | column | octets Integer32 | .1.3.6.1.4.1.4874.2.2.9.1.2.1.5 |
| juniHdlcIfCrcSize Selects the CRC size: none, 16 bits, or 32 bits. | column | Enumeration | .1.3.6.1.4.1.4874.2.2.9.1.2.1.6 |
| juniHdlcIfDataPolarity Polarity of data transmitted on this HDLC interface. Inverted data is
used for certain line coding configurations to ensure sufficient one's
density for timing recovery by the re… | column | Enumeration | .1.3.6.1.4.1.4874.2.2.9.1.2.1.7 |
| juniHdlcIfClockMode The clock mode setting for this HDLC interface. This object is only
applicable to HDLC interfaces directly over a high speed serial
interface (HSSI).
At creation, … | column | Enumeration | .1.3.6.1.4.1.4874.2.2.9.1.2.1.8 |