ieee8021TeipsV2IpgConfigWTR

IEEE8021-TEIPS-V2-MIB · .1.3.111.2.802.1.1.27.1.4.1.6
MIB view Table view

Object

column r/w minutes Unsigned32 
This column is used to configure the
wait-to-restore timer for the IPG operation.
The timer may be configured in steps of 1 minute
between 5 and 12 minutes, the default being 5.
Additionally, the value 0 is used to indicate
that the IPG is to operate non-revertively.  The
value 0 is not permitted if the IPG is configured
for M:1 IPS operation.

Context

MIB
IEEE8021-TEIPS-V2-MIB
OID
.1.3.111.2.802.1.1.27.1.4.1.6
Type
column
Access
readwrite
Status
current
Units
minutes
Parent
ieee8021TeipsV2IpgConfigEntry
Table
ieee8021TeipsV2IpgConfigTable
Siblings
10

Syntax

minutes Unsigned32

Values & Constraints

Object Constraints
range: 0-0 range: 5-12

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
ieee8021TeipsV2IpgConfigState
This column indicates the current state of the protection switching state machine for an IPG. The value can be one of the following: workingSegment(1) The prote…
columnEnumeration.1.3.111.2.802.1.1.27.1.4.1.1
ieee8021TeipsV2IpgConfigNotifyEnable
This column is used to enable or disable transmission of ieee8021TeipsV2IpgAdminFailure notifications. These notifications are generated whenever an administrative command cannot …
columnSNMPv2-TCTruthValue.1.3.111.2.802.1.1.27.1.4.1.10
ieee8021TeipsV2IpgConfigStorageType
This object indicates the persistence of this entry. For permanent objects the ieee8021TeipsV2IpgConfigCommandAdmin column must be writable.
columnSNMPv2-TCStorageType.1.3.111.2.802.1.1.27.1.4.1.11
ieee8021TeipsV2IpgConfigCommandStatus
This column indicates the status of administrative commands within the protection group. It reflects the current operational administrative command being acted upon by the IPG.
columnIEEE8021-TC-MIBIEEE8021TeipsIpgConfigAdmin.1.3.111.2.802.1.1.27.1.4.1.2
ieee8021TeipsV2IpgConfigCommandLast
This column indicates the last attempted administrative command applied to the IPG. It is changed whenever a write is made to the CommandAdmin column of this table and is essenti…
columnIEEE8021-TC-MIBIEEE8021TeipsIpgConfigAdmin.1.3.111.2.802.1.1.27.1.4.1.3
ieee8021TeipsV2IpgConfigCommandAdmin
This column is used by the operator to request that the IPG state machine perform some administrative operation. The operator requests a command by writing the command value to t…
columnIEEE8021-TC-MIBIEEE8021TeipsIpgConfigAdmin.1.3.111.2.802.1.1.27.1.4.1.4
ieee8021TeipsV2IpgConfigActiveRequests
This column shows the status of active requests associated with the IPG.
columnIEEE8021-TC-MIBIEEE8021TeipsIpgConfigActiveRequests.1.3.111.2.802.1.1.27.1.4.1.5
ieee8021TeipsV2IpgConfigHoldOff
This column is used to configure the hold off timer. The purpose is to allow IPS to fix the problem before a higher-layer mechanism, such as PBB-TE TESI protection, is invoked or…
columndeciseconds Unsigned32.1.3.111.2.802.1.1.27.1.4.1.7
ieee8021TeipsV2IpgM1ConfigState
This column indicates the current state of the M:1 protection switching state machine for an IPG if M:1 IPS is supported. The value can be one of the following: psA…
columnEnumeration.1.3.111.2.802.1.1.27.1.4.1.8
ieee8021TeipsV2IpgConfigMWTR
This column is used to configure the M:1 wait-to-restore timer for the IPG operation if M:1 protection is supported. The timer may be configured in steps of 1 minute between 5 an…
columnminutes Unsigned32.1.3.111.2.802.1.1.27.1.4.1.9