hwMplsPsLocalState
HUAWEI-MPLSOAM-MIB ·
.1.3.6.1.4.1.2011.5.12.7.1.3.1.1.20
Object
column
Integer32
The current local state of the protection group. 0: Lockout of Protection (LO) 1: Signal Fail for Protection (SF-P) 2: Forced Switch (FS) 3: Signal Fail for Working (SF) 4: Signal Degrade for Protection(SD-P) 5: Signal Degrade for Working(SD) 6: Manual Switch (MS) 7: Wait-to-Restore (WTR) 8: Exercise (EXER) 9: Reverse Request(RR) 10: Do Not Revert (DNR) 11: No Request (NR) The pripority of the commands are: LO > SF-P > FS > SF > SD-P > SD > MS > WTR > EXER > RR > DNR > NR
Context
- MIB
- HUAWEI-MPLSOAM-MIB
- OID
.1.3.6.1.4.1.2011.5.12.7.1.3.1.1.20- Type
- column
- Access
- readonly
- Status
- current
- Parent
- hwMplsPsEntry
- Table
- hwMplsPsTable
- Siblings
- 19
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-11
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hwMplsPsIndex This is a unique index for an entry in the mplspsEntry. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.1 |
| hwMplsPsSwitchCondition The current switch condition of the protection group.
1: clear,This command clears all of the externally
initiated switch commands listed below;
2: lockout of protection,Fix t… | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.10 |
| hwMplsPsWorkTunnelState The state of working tunnel state in one protection group,
whether it is in detection,
1: it is outof defect
2: it enters defect | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.11 |
| hwMplsPsProtTunnelState The state of protection tunnel state in one protection group,
whether it is in detection,
1: it is outof defect
2: it enters defect | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.12 |
| hwMplsPsSwitchResult Which tunnel is used to transfer the data stream.
1: working-tunnel
2: protection-tunnel | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.13 |
| hwMplsPsCfgType The type of protection switch which is configured.
1: 1:1
2: 1+1
3: shared mesh
4: packet 1:1 | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.14 |
| hwMplsPsCfgProtectTunnId Protect-tunnel id(session-tunnel-id). | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.15 |
| hwMplsPsCfgRevertiveMode Revertive mode is a protection switching mode where revertive
action (switch back to the working LSP) is taken after the
working LSP is repaired.And switching does not occur in … | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.16 |
| hwMplsPsCfgWTR Wait to Restore timer is only applicable for the revertive mode
and applies to a working LSP,It prevents reversion back to
select the working LSP until the Wait to Restore timer… | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.17 |
| hwMplsPsCfgHoldOff The time between declaration of signal degrade or signal fail,
and the initialization of the protection switching algorithm.
step is 100ms.maximum is 10s. | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.18 |
| hwMplsPsRowStatus This variable is used to create, modify, and
delete a row in this table.
1: active
2: not in service
3: not ready
4: create and go
5: create and wait
6: destroy | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.19 |
| hwMplsPsType The type of protection switch,can be 1:1,1+1,shared mesh,
packet 1+1,the default choice is 1:1.
In the 1+1 architecture type, a protection LSP is dedicated to
each working LSP wi… | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.2 |
| hwMplsPsWorkTunnName The name of work-tunnel. | column | OctetString | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.3 |
| hwMplsPsWorkTunnId Work-tunnel id(session-tunnel-id). | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.4 |
| hwMplsPsProtectTunnName The name of protect-tunnel. | column | OctetString | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.5 |
| hwMplsPsProtectTunnId Protect-tunnel id(session-tunnel-id). | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.6 |
| hwMplsPsRevertiveMode Revertive mode is a protection switching mode where revertive
action (switch back to the working LSP) is taken after the
working LSP is repaired.And switching does not occur in … | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.7 |
| hwMplsPsWTR Wait to Restore timer is only applicable for the revertive mode
and applies to a working LSP,It prevents reversion back to
select the working LSP until the Wait to Restore timer… | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.8 |
| hwMplsPsHoldOff The time between declaration of signal degrade or signal fail,
and the initialization of the protection switching algorithm.
step is 100ms.maximum is 10s. | column | Integer32 | .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.9 |