hh3cDot11RRMRadioType
HH3C-DOT11-RRM-MIB ·
.1.3.6.1.4.1.25506.2.75.8.1.2.1.1
Object
column
HH3C-DOT11-REF-MIBHh3cDot11RadioType
802.11 radio type.
Context
- MIB
- HH3C-DOT11-RRM-MIB
- OID
.1.3.6.1.4.1.25506.2.75.8.1.2.1.1- Type
- column
- Access
- noaccess
- Status
- current
- Parent
- hh3cDot11RRMRadioCfgEntry
- Table
- hh3cDot11RRMRadioCfgTable
- Siblings
- 12
Syntax
HH3C-DOT11-REF-MIBHh3cDot11RadioType
- Source
- HH3C-DOT11-REF-MIBHh3cDot11RadioType
- Base type
Enumeration
Values & Constraints
Type Values
1 | dot11a |
2 | dot11b |
4 | dot11g |
8 | dot11n |
16 | dot11gn |
32 | dot11an |
64 | dot11ac |
128 | dot11gac |
256 | dot11ax |
512 | dot11gax |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hh3cDot11RRMCfgNoiseThres Configure the noise threshold. | column | Integer32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.10 |
| hh3cDot11RRMCfgPERThres Configure the CRC error threshold.
If the percentage of CRC errors reaches the threshold, RRM will perform
resource adjustment to control the situation. | column | percent Integer32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.11 |
| hh3cDot11RRMCfgToleranceFctr Configure the tolerance level.
During dynamic frequency selection (DFS), the channel will be changed
only if there is a better channel having lesser interference and packet
error … | column | percent Integer32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.12 |
| hh3cDot11RRMCfgAdjacencyFctr Configure the adjacency factor for the band.
If transmit power control (TPC) is configured, power will be adjusted
when the nth neighbor is detected. The value n is the adjacency… | column | Integer32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.13 |
| hh3cDot11RRMCfgChlState Enable/Disable dynamic channel selection. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.25506.2.75.8.1.2.1.2 |
| hh3cDot11RRMCfgChlMode Configure the mode of channel selection.
This node can be configured only when dynamic channel selection
is enabled. | column | Enumeration | .1.3.6.1.4.1.25506.2.75.8.1.2.1.3 |
| hh3cDot11RRMChlProntoRadioElmt Specify the AP and radio that will change channel at next
calibration cycle.
0 is returned when getting the value of this node.
This node can be configured only when the mode of c… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.4 |
| hh3cDot11RRMCfgPwrState Enable/Disable dynamic power selection for the band. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.25506.2.75.8.1.2.1.5 |
| hh3cDot11RRMCfgPwrMode Configure the mode of transmit power control.
This node can be configured only when dynamic power selection
is enabled. | column | Enumeration | .1.3.6.1.4.1.25506.2.75.8.1.2.1.6 |
| hh3cDot11RRMPwrProntoRadioElmt Specify the AP and radio that will change power at next
calibration cycle.
0 is returned when getting the value of this node.
This node can be configured only when the mode of tra… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.7 |
| hh3cDot11RRMCfgIntrvl Configure the calibration interval. | column | minute SNMPv2-SMIInteger32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.8 |
| hh3cDot11RRMCfgIntrfThres Configure the interface threshold.
By default, interference observed on an operating channel is considered
during dynamic frequency selection and transmit power control. If the
i… | column | percent Integer32 | .1.3.6.1.4.1.25506.2.75.8.1.2.1.9 |